Acquiring Hyperpolarized 129Xe Magnetic Resonance Images of Lung Ventilation

Summary

Hyperpolarized ¹²⁹Xe magnetic resonance imaging (MRI) is a method for studying regionally resolved aspects of pulmonary function. This work presents an end-to-end standardized workflow for hyperpolarized ¹²⁹Xe MRI of lung ventilation, with specific attention to pulse sequence design, ¹²⁹Xe dose preparation, scan workflow, and best practices for subject safety monitoring.

Abstract

Hyperpolarized ¹²⁹Xe MRI comprises a unique array of structural and functional lung imaging techniques. Technique standardization across sites is increasingly important given the recent FDA approval of ¹²⁹Xe as an MR contrast agent and as interest in ¹²⁹Xe MRI increases among research and clinical institutions. Members of the ¹²⁹Xe MRI Clinical Trials Consortium (Xe MRI CTC) have agreed upon best practices for each of the key aspects of the ¹²⁹Xe MRI workflow, and these recommendations are summarized in a recent publication. This work provides practical information to develop an end-to-end workflow for collecting ¹²⁹Xe MR images of lung ventilation according to the Xe MRI CTC recommendations. Preparation and administration of ¹²⁹Xe for MR studies will be discussed and demonstrated, with specific topics including choice of appropriate gas volumes for entire studies and for individual MR scans, preparation and delivery of individual ¹²⁹Xe doses, and best practices for monitoring subject safety and ¹²⁹Xe tolerability during studies. Key MR technical considerations will also be covered, including pulse sequence types and optimized parameters, calibration of ¹²⁹Xe flip angle and center frequency, and ¹²⁹Xe MRI ventilation image analysis.

Introduction

Hyperpolarized ¹²⁹Xe MRI is an exciting tool for non-invasive, spatially-resolved characterization and quantification of specific aspects of pulmonary function^1,2,3. Acquisition and reconstruction approaches similar to those used in anatomical proton MRI yield images of inhaled ¹²⁹Xe in the lungs, permitting visualization of non-ventilated lung regions and region-resolved quantification of ventilation distribution^4,5,6,7,8. More advanced pulse sequence and analysis techniques yield further complementary information, including quantification of gas-exchange efficacy between alveoli and pulmonary capillaries via spectroscopic MRI^{9,10,11,12,13} and characterization of alveolar microstructure integrity via diffusion-weighted MRI^14,15,16.

Inhaled ¹²⁹Xe has been proven safe and tolerable in adult and pediatric subjects, including those with pulmonary disease^17,18. Measurements of lung function derived from ¹²⁹Xe MRI have shown sensitivity to structural and functional alterations in many pulmonary disease contexts, including chronic obstructive pulmonary disease^6,10,19, cystic fibrosis^20,21,22, idiopathic pulmonary fibrosis^23,24,25, and asthma^7,10,26. Given the high safety and tolerability of ¹²⁹Xe MRI, the lack of ionizing radiation in MRI compared with other common imaging approaches, and the high reproducibility of ¹²⁹Xe MRI results^27,28, ¹²⁹Xe MRI holds significant promise, in particular for precise serial monitoring of individuals receiving a time course of therapy for chronic pulmonary disease.

The safety and clinical promise of ¹²⁹Xe MRI have led to its FDA approval in December 2022 for lung ventilation imaging in persons aged 12 years and older²⁹. Given this, it is anticipated that the number of research and clinical sites capable of performing ¹²⁹Xe MRI (currently ~20 worldwide) will increase significantly over the coming years. As ¹²⁹Xe MRI spreads to new institutions, it is important that robust methodological resources exist to allow sites to build out clinically relevant ¹²⁹Xe MRI techniques quickly and to perform scans and generate results that are closely comparable with those of existing sites.

In this work, we will outline the current best practices for human hyperpolarized ¹²⁹Xe MRI of lung ventilation, as agreed upon by member institutions of the ¹²⁹Xe MRI Clinical Trials Consortium (Xe MRI CTC) and summarized in a recent position paper³⁰. Topics will include the preparation of tailored pulse sequences ideal for a complete ¹²⁹Xe MRI workflow, preparation, and administration of hyperpolarized ¹²⁹Xe gas, an optimized workflow for human ¹²⁹Xe MRI sessions, and best practices for monitoring subject safety and comfort during MRI sessions.

Protocol

All research involving human subjects must be approved by an institutional review board (IRB). IRB involvement is not necessary for regulatory-approved clinical use of ¹²⁹Xe MRI. Before participating in a research study, prospective subjects must be provided with an approved informed consent document. The person obtaining consent must explain the contents of the document, including the purpose, procedures, benefits, and risks of the study, must answer any questions, and must obtain consent from the subject to proceed with the study as documented by the subject's signature on the informed consent document. In the case of pediatric subjects or other special circumstances, approved practices for obtaining consent must be followed. The protocol described below follows the guidelines of the IRB of the University of Virginia, and the example case subjects in this manuscript have signed the University of Virginia IRB-approved consent forms (IRB 13647, 16215, 16885, 19569).

1. Preparation of hardware and pulse sequences for ¹²⁹Xe MRI

NOTE: The protocol steps under step 1 should be performed before scanning any human subjects. They do not need to be repeated for each subject.

1. Verify that the MRI scanner is capable of multinuclear operation including ¹²⁹Xe.
2. Verify that the ¹²⁹Xe radio-frequency (RF) coil can be connected to the MRI scanner, using a purpose-built coil-to-scanner interface box if required.
3. Verify that suitable software (often called a coil file) for interfacing the ¹²⁹Xe RF coil to the MRI scanner is installed if required by the scanner manufacturer.
4. Prepare pulse sequences for ¹²⁹Xe and ¹H imaging as described below.
   1. For ¹²⁹Xe calibration, prepare a non-localized, spectroscopic sequence comprising a series of free induction decays (FIDs) using the pulse sequence parameters provided in Table 1.
      NOTE: The FIDs acquired at ~218 ppm (dissolved-phase frequency) are used primarily to determine parameters for dissolved-phase ¹²⁹Xe MRI, which is not covered in the present work. However, these parameters are given so that one can develop a single standardized ¹²⁹Xe calibration that suffices for ¹²⁹Xe MRI scans of any type. Additionally, note that a separate calibration scan may not be needed for studies involving only ¹²⁹Xe ventilation imaging once the site acquires sufficient experience. The ¹²⁹Xe operating frequency can be accurately estimated by scaling the scanner-determined ¹H frequency by the ratio of ¹²⁹Xe to ¹H gyromagnetic ratios, and the transmitter calibration can be estimated based on accumulated experience and subject weight.
   2. For ¹²⁹Xe ventilation MRI, prepare a two-dimensional (2D) RF-spoiled gradient-echo sequence using the pulse sequence parameters provided in Table 2. Ensure that ¹²⁹Xe is selected as the target nucleus.
   3. For conventional ¹H anatomical MRI, prepare a single-shot turbo/fast spin-echo sequence or an RF-spoiled gradient-echo sequence using the parameters provided in Table 2.
      NOTE: For ¹²⁹Xe ventilation and ¹H anatomical sequences, FOV and the number of slices are subject-specific. Choose these parameters at the beginning of the scan session in such a way as to ensure full coverage of the lungs in all three dimensions.
      1. Enable phase oversampling to mitigate potential aliasing of the arms into the imaging FOV.
      2. MRI scanner vendor limitations may prevent the operation of the single-shot turbo/fast spin-echo sequence at the coarse in-plane resolution suggested (4 mm x 4 mm). If this is the case, use a resolution that is an integer factor of the desired resolution (e.g., 2 mm x 2 mm).
         NOTE: The ¹H anatomical scan can alternatively be acquired using a 2D RF-spoiled gradient echo sequence. In this case, use the same parameters as the ventilation scan parameters given in Table 2 but enable phase oversampling to avoid aliasing of the arms into the imaging FOV.
5. Verify the operation of the RF coil and pulse sequences outlined above by performing scans of a thermally polarized ¹²⁹Xe phantom³¹ for ¹²⁹Xe scans and a ¹H phantom for ¹H scans.

Parameter	Calibration
TR	15 ms
TE	0.45 ms (3 T), 0.8 ms (1.5 T)
RF pulse	windowed sinc
RF duration	0.65-0.69 ms (3 T), 1.15-1.25 ms (1.5 T)
Flip angle	20°
RF frequency	218 ppm (dissolved-phase), 0 ppm (gas-phase)
Dwell time	39 μs
Bandwidth	25.6 kHz
No. of samples	256 (not including oversampling, if used)
Readout duration	10 ms
Number of FIDs	1 noise (no RF), 499 at dissolved-phase freq., 20 at gas-phase freq.
Gradient spoiling	moment of at least 15 mT/m-ms (each axis, after each FID)
Duration	~8 s

Table 1: Recommended pulse sequence parameters for ¹²⁹Xe calibration. Parameters are given for a non-localized, spectroscopic ¹²⁹Xe calibration pulse sequence.

Parameter	Ventilation	Anatomical
Sequence type	RF-spoiled gradient-echo	Single-shot turbo/fast spin-echo
TR	<10 ms	Infinite
TE	<5 ms	<50 ms
Echo spacing	N/A	3-5 ms
Excitation flip angle	8-12°	90°
Refocusing flip angle	N/A	≥90° (highest allowed within SAR limits)
Slice thickness	15 mm	15 mm
Slice gap	None	None
Slice orientation	Coronal	Coronal
Slice order	Sequential (anterior to posterior)	Sequential (anterior to posterior)
Phase-encoding order	Sequential (left to right)	Sequential (left to right)
NEX	1 (up to 7/8 partial Fourier permitted)	Half Fourier
Asymmetric echo	Allowed	N/A
Voxel size	4 x 4 x 15 mm3	4 x 4 x 15 mm3
Sampling duration per echo	5-7 ms	1-1.5 ms
Scan duration	8-12 s	≤16 s

Table 2: Recommended pulse sequence parameters for ¹²⁹Xe ventilation and ¹H anatomical imaging. Parameters are given for a 2D RF-spoiled fast gradient-echo sequence for ¹²⁹Xe ventilation imaging (first column) and a 2D single-shot turbo/fast spin-echo sequence for ¹H anatomical imaging (second column). Note that the anatomical scan can alternatively be acquired using a 2D RF-spoiled gradient echo sequence. In this case, use the same parameters as the ventilation scan parameters given here, but add phase oversampling as needed to avoid aliasing of the arms into the imaging FOV. Also, note that the particular method for specifying receiver bandwidth varies across scanner manufacturers but that the correct value can be calculated for any scanner manufacturer from the given sampling duration per echo.

2. Screening and preparation of candidates for ¹²⁹Xe MRI

1. Ensure that there are no contraindications for MRI in the prospective subject by surveying them with an MR safety form. Supplementary File 1 depicts an example form used at the University of Virginia.
2. Ensure that the prospective subject does not meet any exclusion criteria particular to ¹²⁹Xe MRI examinations, which might include, but are not limited to: percent-predicted FEV₁ less than 25%, a decompensated respiratory condition within the previous 6 weeks, chest circumference larger than the interior circumference of the ¹²⁹Xe RF coil, and history of unstable cardiac disease.
   NOTE: Additional criteria that do not indicate immediate exclusion but warrant careful individual consideration include: the need for significant supplemental oxygen at baseline (i.e., greater than 3 L/min by nasal cannula) and a history of neurologic disorder with baseline abnormalities.
3. If performing lung diffusion testing (DLCO) or spirometry during the imaging visit, instruct the subject not to ingest carbonated beverages on the day of the study visit. If a subject uses prescribed respiratory medication, instruct them to delay or refrain from taking it if specified by the study protocol.

3. Preparation of hyperpolarized  ¹²⁹Xe doses

NOTE: Detailed ¹²⁹Xe polarizer and polarization measurement station instructions are proprietary and specific to each vendor. The instructions below comprise a basic summary for general spin-exchange optical pumping ¹²⁹Xe polarizer operation.

1. Decide on a dose volume for the subject. Commonly, a total dose volume of 1 L is chosen for all subjects, and this total dose volume is specified in the FDA label for ¹²⁹Xe MRI. However, current Xe MRI CTC recommendations³⁰ suggest that the total dose volume (xenon plus either nitrogen or helium) should target 1/5^th of the subject's forced vital capacity (FVC) to ensure a comfortable amount of gas to inhale for each subject and to minimize effects related to lung volume difference between subjects.
   1. If recent spirometry results are available for the subject, use these to determine 1/5^th of FVC. If spirometry results are unavailable, estimate the subject's total lung capacity (TLC) based on height, sex, and race, and estimate the total dose as 1/6^th of TLC.
2. Decide on a volume of xenon gas to polarize.
   NOTE: Target xenon volumes for each dose bag are given as dose equivalent (DE) volumes, which conceptually indicate the equivalent volume of 100% enriched, 100% polarized ¹²⁹Xe gas. Conceptually, DE volume is directly proportional to the expected signal-to-noise ratio (SNR) of a ¹²⁹Xe scan, and recommended DE volume will be higher or lower for certain ¹²⁹Xe scan types based on the SNR required for that scan type.
   1. Calculate the DE volume for a given xenon dose as follows³²:
      
      where V_Xe is the total volume of xenon gas (all isotopes, not just ¹²⁹Xe) in the dose, f_129Xe is the ¹²⁹Xe isotopic enrichment, and P_129Xe is the ¹²⁹Xe polarization.
   2. Choose the total necessary DE volumes for the set of ¹²⁹Xe scans that will be performed. The recommended DE volumes for individual calibration and ventilation scans are 75-150 mL.
      NOTE: For ventilation imaging, the SNR must be high enough to robustly distinguish between ventilated and non-ventilated image voxels. A DE volume of 50 mL is considered the absolute minimum for ventilation imaging³⁰ to achieve an expected SNR of at least 20. For calibration scans, a DE volume as low as 25 mL may be acceptable if only the gas-phase signal is calibrated; at least 75 mL should be used if calibrating both the gas-phase and dissolved-phase signals.
3. Use the total necessary DE volume, known ¹²⁹Xe isotropic enrichment of the xenon gas, and estimated ¹²⁹Xe polarization based on previous polarization runs to calculate the total required xenon gas volume for polarization. An example calculation is shown below for one ventilation scan (DE volume = 75 mL), assuming ¹²⁹Xe isotopic enrichment of 85% and polarization of 20%³²:
   
   Perform this calculation for each xenon dose to determine the correct volume of polarized xenon gas to dispense into each dose bag.
   1. Subjects with low BMI (<21) have a higher risk of more profound central nervous system (CNS) effects following ¹²⁹Xe inhalation than other subjects. Consult a physician before imaging low-BMI subjects and consider minimizing ¹²⁹Xe dose volumes to avert these potential issues.
4. Prepare the ¹²⁹Xe polarizer according to all instructions supplied by the polarizer vendor.
   1. Steps may include the following, depending on polarizer vendor: ensure that the Helmholtz coil power supply is ON; evacuate the outlet manifold to clear any impurities; set up the liquid nitrogen dewar around/beneath the cold finger; turn ON power to the lasers and allow them to warm up; turn ON airflow to the oven, set the oven to the appropriate temperature using the oven controller, and allow the oven to warm up.
      CAUTION: Liquid nitrogen can cause severe frostbite if it comes in contact with skin, eyes, or clothing, and high-intensity laser light can cause eye injury if impingent upon the eye without protection. Use appropriate caution and wear protective gear as needed.
5. Ensure the ¹²⁹Xe polarization measurement station is powered ON and the software is ready to measure dose polarization.
6. Begin collection of hyperpolarized ¹²⁹Xe by performing the following steps.
   1. Start nitrogen flow to the cold finger warming jacket.
   2. Start xenon mixture flow to the cold finger. Refer to polarizer performance curves in polarizer documentation to choose the optimal flow rate.
   3. Add liquid nitrogen to the dewar surrounding the cold finger.
   4. Record polarization start time on a data sheet to ensure accurate polarization volume.
   5. Once collection has started, adjust flow and oven controllers to maintain consistent flow rate and temperature, and add liquid nitrogen as needed to keep the dewar full.
7. During xenon accumulation, prepare Tedlar dose bags for dose collection by repeatedly purging and evacuating bags at least 3x using the polarizer outlet manifold to minimize impurities and/or depolarizing gases in the bags.
8. Once the appropriate time for collection of desired hyperpolarized ¹²⁹Xe volume has elapsed, terminate hyperpolarized ¹²⁹Xe collection as directed in the polarizer documentation.
9. Thaw the frozen ¹²⁹Xe that has precipitated in the cold finger, as described below.
   1. Attach a ¹²⁹Xe dose bag to the xenon outlet on the outlet manifold.
   2. Carefully remove the liquid nitrogen dewar and replace it with a thawing vessel containing room temperature water.
   3. While thawing, monitor pressure continuously, opening the flow valve from the cold finger to the xenon outlet once the pressure reaches a threshold value given in the polarizer documentation and quickly closing the valve as the pressure drops.
   4. Continue dispensing sublimated xenon gas into the dose bag in this manner until the desired amount of xenon in the dose bag is reached.
   5. Add the buffer gas (nitrogen or helium) at this time if it was not added to the bag previously.
   6. Once all desired xenon and buffer gases are added to the bag, quickly close the pinch clamp on the bag tubing, close the xenon outlet valve, and detach the full-dose bag from the polarizer.
   7. Move the bag immediately to the magnetic field created by the Helmholtz coil pair of the ¹²⁹Xe polarization measurement station.
      CAUTION: Pressure will rapidly build in the cold finger as the xenon gas warms and sublimates, creating a potential explosion risk if pressure is allowed to build beyond safe limits. Follow the instructions for this step provided in polarizer documentation exactly, and wear eye protection while performing this step.
10. Measure and record polarization in each dose bag at the ¹²⁹Xe polarization measurement station, according to the instructions provided by the polarization measurement station vendor.
11. Once polarization is measured, keep ¹²⁹Xe dose bags in the magnetic field created by the Helmholtz coil pair of the polarization measurement station until ready to administer a dose to the subject.

4. Pre-scan preparation and coaching of subject

NOTE: It is recommended that if the subject receives a full exam that includes a six-minute walk test, the walk should not take place until after ¹²⁹Xe MRI is completed to avoid fatiguing the subject in a manner that could potentially impact ¹²⁹Xe MRI results. This is particularly relevant for patients with cardiopulmonary disease.

1. Confirm that the subject has correctly carried out all pre-visit instructions as described in step 2, and that no changes to health that would meet any study exclusion criteria or constitute an MRI contraindication have occurred since the subject was screened.
2. Perform all necessary physical tests on the subject, including an electrocardiogram (ECG); a collection of vitals including body temperature, heart rate, respiration rate, blood oxygen saturation (SpO₂), and blood pressure; spirometry; and a DLCO test.
3. Monitor these tests for any potential warning signs, including low SpO₂ (<92%), elevated blood pressure, or significant deviation of test results from any existing baselines for the subject.
   NOTE: These readouts, particularly baseline SpO₂, are checked because of the expectation that mild transient oxygen desaturation will occur during ¹²⁹Xe inhalation. For subjects with baseline SpO₂ <92% or other warning signs, consult a physician to confirm the suitability of the subject for ¹²⁹Xe MRI testing and whether to use supplemental O₂ between ¹²⁹Xe inhalations.
4. Coach the subject in the correct ¹²⁹Xe inhalation procedure, as described below.
   1. Prepare one or more Tedlar bags containing air for the subject to practice outside the scanner. Use an air volume that matches the total volume of xenon and buffer gas that will be inhaled from the bag during the actual study.
   2. Prepare nose clips for the subject to wear during breath-hold scanning. Fit the nose clips onto the subject's nose before the start of breath holds (both for practice and actual scanning).
   3. Coach the subject using one air-filled bag for each attempt, following the instructions below. The subject should begin inhaling the bag from a target volume of functional residual capacity. During the procedure below, monitor the subject's chest to confirm that they are executing the instructions as given.
      1. Have the bag ready, but do not administer it to the subject yet. Ask the subject to: Take a regular breath in. Breathe it out. Take a regular breath in. Breathe it out.
      2. Place the tube attached to the Tedlar bag into the subject's mouth. Hold the bag where the subject can inhale from it and open the valve. Ask the subject to: Breathe in. Breathe in. Breathe in.
      3. Once the subject has inhaled the entire bag contents, ask the subject to: Hold your breath. Immediately instruct the scanner operator to: Go!
         NOTE: When scanning the subject, the scanner operator should start the scan upon hearing Go! This instruction is not intended for the subject (that is, they should remain still and continue holding their breath as instructed immediately beforehand) but does alert the subject that scanning is imminent.
      4. Wait for the scan to finish, or when practicing, for a count of 10-15 s, which is the approximate amount of time required for a typical ¹²⁹Xe scan to elapse.
      5. Ask the subject to: Breathe. The subject exhales at this point. Coach the subject to take several deep breaths in and out at this point to facilitate quicker clearance of ¹²⁹Xe from the lungs and a quicker return to normal oxygen saturation levels.
      6. Verify that the subject is able to carry out these instructions reliably. Consider excluding subjects who are unable to inhale the entire gas volume, unable to maintain breath-hold, or who persistently cough during breath-hold attempts during the test.
         ​NOTE: The outcome of this test is critical to determine likely imaging quality. This check for reliable subject compliance is particularly important in the contexts of pediatric imaging and imaging of severe lung disease, as subjects in either or both of these categories are more likely to struggle to reliably complete the required breath-hold.

5. Preparation of MRI scanner room and positioning of subject on scanner patient table

1. Ensure that anyone who enters or might be expected to enter the MRI scanner room (subject and personnel) removes all metallic and/or electronic objects from their pockets and person prior to entering the scanner room.
2. Prepare the ¹²⁹Xe vest coil by plugging it into the scanner and placing it on the MRI scanner patient table.
3. Instruct the subject to lie on the patient table in a feet-first supine position (or head-first supine, if better suited for the layout of the scanner room). Place pillows under the subject's head, knees, etc., in consultation with the subject to ensure that the subject can comfortably lie still throughout the examination.
4. Secure the ¹²⁹Xe vest coil around the subject's chest. Aim for the midline of the coil in the head-foot direction to lie as close as possible to the expected midline of the subject's lungs at a comfortable lung inflation level to avoid signal reductions at the periphery of the lungs.
   NOTE: It is a common error to position the coil too far in the direction of the subject's feet. Positioning the coil as directed above may put the coil further toward the subject's head than might naively be expected. Additionally, the subject's arms may need to be positioned above their head and outside the coil if the subject's chest diameter necessitates this. The specific chest diameter above which this positioning is required will vary depending on specific scanner and coil hardware. For smaller subjects, arms can be positioned either above the head and outside the coil or at the sides and inside the coil.
5. Set up an MRI-safe pulse oximeter next to the patient table in the MRI scanner room and connect the pulse oximeter probe to the subject. Verify that the pulse oximeter is reading correctly.
6. Place a nasal cannula in the subject's nose (or, for a healthy subject, have one standing by in the scanner room) and connect it to an oxygen source to be used if the subject's SpO₂ drops more than 10% for more than 2 min after dose inhalation. Place the oxygen tank and regulator in an MR-safe manner based on local safety policy within reachable distance.
7. Advance the patient table into the MRI scanner, aligning the midline of the coil/subject's lungs to the scanner's isocenter.

6. Scanning procedure

1. In the user interface on the MRI scanner, enter subject data and open the previously prepared (as described in step 1) ¹²⁹Xe MRI protocol.
2. Ensure that ¹²⁹Xe doses have been prepared as described in step 3 and that ¹²⁹Xe dose bags are in the magnetic field generated by the polarization measurement station's Helmholtz coil pair (or in an equivalent device) to minimize ¹²⁹Xe depolarization rate.
3. Perform a ¹H localizer scan using a standard vendor-provided protocol (e.g., a three-plane localizer) as described below.
   1. Instruct the subject to take a comfortable, natural breath in and hold their breath. While the subject holds their breath, execute the localizer scan.
   2. View results of the localizer scan on the MRI scanner interface. If images show artifacts (e.g., if metal-containing clothing was not removed), resolve any issues and repeat the localizer. If the localizer FOV is poorly centered on the subject, reposition the subject and repeat. Once acceptable localizer images have been obtained, proceed to the next step.
4. Perform initial pre-scan adjustments for ¹²⁹Xe scans as described below.
   1. Set the initial ¹²⁹Xe center frequency by dividing the ¹H center frequency from the localizer by 3.61529 (the approximate ratio of the respective gyromagnetic ratios of ¹H and ¹²⁹Xe).
   2. Set the initial ¹²⁹Xe transmitter setting based on calibration results from previous subjects with similar body habitus, scaling based on ¹H reference voltage, or the subject's measured weight. Details of ¹²⁹Xe transmitter settings are specific to the scanner and ¹²⁹Xe coil manufacturers.
   3. Use the scanner's default shim settings for all ¹²⁹Xe acquisitions.
5. After performing the pre-scan adjustments described above, acquire the ¹²⁹Xe calibration scan to find the ¹²⁹Xe center frequency and transmitter settings as described below.
   1. Load the ¹²⁹Xe calibration sequence from the prepared protocol. Ensure all pulse sequence parameters are as desired and set the scan execution setting such that the scan can be executed with a single click.
   2. Bring the ¹²⁹Xe dose bag intended for the ¹²⁹Xe calibration scan from the polarization measurement station into the scanner room. Hold or place the dose bag at the ready near the subject; avoid regions near the bore opening where the magnetic field strength changes rapidly.
   3. Assist the subject in inhaling the ¹²⁹Xe dose from the bag, following the coached inhalation procedure outlined in step 4.
   4. Execute the scan immediately upon hearing Go! signaled by the individual assisting the subject.
   5. Monitor the subject while the scan proceeds. If the subject visibly exhales, coughs, moves, etc., repeat the scan if possible.
   6. As soon as the scan finishes, instruct the subject to exhale and breathe freely.
   7. Following the scan, monitor the subject's heart rate and SpO₂ using the pulse oximeter and monitor for transient central nervous system effects (such as dizziness, light-headedness, euphoria, and paresthesia) via verbal communication with the subject.
      NOTE: Almost all subjects will experience very mild CNS effects that require no intervention, with the exception of subjects with low body fat content, as referred to in step 3.2.
   8. Wait for any deviations from baseline to dissipate before administering another ¹²⁹Xe dose. If no significant deviations from baseline occur, wait at least 2 min before administering another ¹²⁹Xe dose.
      NOTE: A typical time course of oxygen de-saturation and recovery is as follows: de-saturation starts 10-20 heartbeats after completing ¹²⁹Xe inhalation, nadir occurs 20-30 heartbeats after completing inhalation, and recovery occurs within 45-50 heartbeats after completing inhalation. Most de-saturation resolves within 30 s of ¹²⁹Xe inhalation and should be typically expected to entirely resolve within 2 min. Consult a physician if persistent de-saturation (greater than 10% of subject baseline) continues beyond 2 min, as it may be advisable to avoid giving any further ¹²⁹Xe doses and/or end the study.
6. Perform the ¹²⁹Xe calibration analysis as described below (e.g., using a standalone analysis tool).
   1. Determine ¹²⁹Xe center frequency using the spectrum from the first gas-phase FIDs.
   2. Determine ¹²⁹Xe transmitter adjustment as described below.
      1. Fit the peak intensities of the 20 gas-phase FIDs to the following function³⁰ and solve for the flip angle, α:
         
         where S_i is the magnitude of the signal intensity resulting from the ith excitation, S₀ is the magnitude of the signal intensity from the first excitation, and C is a noise offset parameter.
      2. Once α is obtained, scale the initial ¹²⁹Xe transmitter setting for subsequent scans by 20°/α, assuming that 20° was used as the intended calibration flip angle as recommended in Table 1.
7. Once final ¹²⁹Xe pre-scan adjustments have been made and the subject is ready for the next ¹²⁹Xe dose, perform the ¹²⁹Xe ventilation scan as described below.
   1. Load the ¹²⁹Xe ventilation sequence from the prepared protocol. Ensure all pulse sequence parameters are as desired and set the scan execution setting such that the scan will begin immediately following a single click.
   2. Select FOV size and center location based on the localizer results. Aim for the center of the FOV to coincide with the center of the lungs in all three dimensions and aim for the FOV to be large enough to comfortably contain the entire chest cavity, including the entirety of both lungs.
   3. Bring the ¹²⁹Xe dose bag intended for the ¹²⁹Xe ventilation scan from the polarization measurement station into the scanner room. Hold or place the dose bag at the ready near the subject; avoid regions near the bore opening where the magnetic field strength changes rapidly.
   4. Assist the subject in inhaling the ¹²⁹Xe dose from the bag, following the coached inhalation procedure outlined in step 4.
   5. Execute the scan immediately upon hearing Go! signaled by the individual assisting the subject.
   6. Monitor the subject while the scan proceeds. If the subject visibly exhales, coughs, moves, etc., repeat the scan if possible.
   7. As soon as the scan finishes, instruct the subject to exhale and breathe freely.
   8. Following the scan, monitor the subject's heart rate and SpO₂ using the pulse oximeter and monitor for transient central nervous system effects (such as dizziness, light-headedness, euphoria, and paresthesia) via verbal communication with the subject.
   9. Wait for any deviations from baseline to dissipate before administering another ¹²⁹Xe dose. If no significant deviations from baseline occur, wait at least 2 min before administering another ¹²⁹Xe dose.
8. Perform ¹H anatomical scan as described below.
   1. Load the ¹H anatomical sequence from the prepared protocol. Ensure all pulse sequence parameters are as desired and set the scan execution setting such that the scan can be executed with a single click.
   2. Bring the dose bag filled with air and matched to the volume of the dose bag used for the ¹²⁹Xe ventilation scan into the scanner room.
   3. Assist the subject in inhaling the air dose from the bag, following the coached inhalation procedure outlined in step 4.
   4. Execute the scan immediately upon hearing Go! signaled by the individual assisting the subject.
   5. Monitor the subject while the scan proceeds. If the subject visibly exhales, coughs, moves, etc., repeat the scan if possible.
   6. As soon as the scan finishes, instruct the subject to exhale and breathe freely.

7. Post-scan procedures

1. Take measurements of the subject's vitals in the same manner as before the scan procedure. If any vitals become abnormal, instruct the subject to wait 30-60 min and/or until vitals return to near-baseline before departing.

8. Analysis of ¹²⁹Xe MRI ventilation data

NOTE: The acquired ¹²⁹Xe ventilation and ¹H anatomical images should automatically be reconstructed on the MRI scanner computer using the vendor's default image reconstruction pipeline.

1. Export ¹²⁹Xe ventilation and ¹H anatomical scans as DICOM image files using the minimum level of interpolation allowed (ideally none).
2. Calculate ventilation defect percentage (VDP) with programming or image-analysis software using the following equation⁸:
   
   1. Determine ventilated volume by segmenting ¹²⁹Xe ventilation scans, either manually or using one of a number of existing automated approaches³³.
      NOTE: A simple method for binarized segmentation of ¹²⁹Xe images uses a threshold defined as follows⁸:
      
      where "Mean signal" is the mean of the ¹²⁹Xe signal intensity within a user-defined region-of-interest of strong ¹²⁹Xe signal within the lungs, and "SD(Noise)" is the standard deviation of the ¹²⁹Xe signal intensity within a region near the edge of the field-of-view located far from the lungs or trachea.
   2. Determine total lung volume by segmenting ¹H anatomical scans, either manually or using existing automated approaches³⁴.
   3. Once these segmentations are performed, calculate corresponding volumes as the number of segmented voxels times the image voxel volume (accounting for any interpolation performed when converting the images to DICOM files).

Results

Figure 1 shows representative ventilation and three-plane localizer images from a healthy individual. High ¹²⁹Xe signal can be observed throughout the lungs in the ventilation images, and no ventilation impairment is evident in this individual.

Figure 2, Figure 3, and Figure 4 show representative ventilation and anatomical images from diseased individuals.

Discussion

The ventilation and anatomical MRI approaches outlined above are designed to maximize image quality and SNR while maintaining simplicity of implementation - these sequence protocols can in general be adapted from vendor product pulse sequences, provided multinuclear operation is enabled, and images will automatically reconstruct on the scanner computer. One disadvantage of the 2D approaches described here is the use of slice-selective excitation RF pulses, which introduces signal differences between slices collected earl...

Materials

Name	Company	Catalog Number	Comments
1.5T or 3T human MRI scanner	Siemens		MAGNETOM Symphony (1.5T) or Vida (3T); older models fine, as long as multinuclear option is/can be installed; scanners also available from GE and Philips
129Xe hyperpolarizer	Polarean	9820
129Xe MRI phantom
129Xe MRI vest coil	Clinical MR Solutions		Also available from other vendors
129Xe polarization measurement station	Polarean	2881
1H MRI phantom
Coil file for 129Xe MRI vest coil			Also available from other vendors for their respective coils
ECG machine
Helium buffer gas
Interface box from coil to scanner			May be built into coil, but needs to be included separately if not
Liquid nitrogen
MRI-safe pulse oximeter	Philips	Expression MR200
Nitrogen buffer gas
PFT machine
Programming/image analysis software	MATLAB	R2023a	Various other options available
Pulse sequence design software	Siemens		IDEA software package; also available from GE and Philips for their respective scanners
Scanner multinuclear option	Siemens		Scanner integrated hardware/software package; also available from GE and Philips for their respective scanners
Tedlar gas sampling bags (500, 750, 1000, 1250, 1500 mL)
Xenon gas (129Xe isotopically enriched)