JS is indebted to Prof. B. Hoge of the Inorganic Chemistry department, Bielefeld University, for the idea of establishing the presented inlet system. The analyzed phosphane was a generous gift from Prof. B. Hoge. Sample preparation of the analyzed compound was performed by M. Wiesemann. Photographs of the phospane were taken by Dr. J. Bader. The mechanical workshop of the faculty of chemistry is acknowledged for the manufacturing of the interface and the glass workshop of the faculty of chemistry for the manufacturing of the lockable test tubes with flanges. Prof. B. Hoge and Prof. H. Gr&#246;ger are acknowledged for funding of this publication.

1. Sample Preparation
<ol>
	<li>Use custom-made lockable test tubes with a flange (Figure 1) for transportation and transfer of the samples into the mass spectrometer. Prior to filling with sample, evacuate the lockable test tubes attached to a multiple manifold Schlenk line and remove residual water by heating with a heat gun. Vent the test tube with dry Argon and evacuate again, while heating.</li>
	<li>Immerse the lockable test tube into a cold trap filled with liquid nitrogen (CAUTION: Be careful when working with liquid nitrogen). Condense the sample into the test tube from a sample container attached to a manifold of the Schlenk line, close the lock on top of the test tube as well as the manifold and remove the locked test tube from the nitrogen bath. As mass spectrometry is very sensitive, a small amount is sufficient. Most of the analyte will remain in the lockable test tube during the analysis and is available for further experiments after the measurement.</li>
</ol>
<img alt="Figure 1" fo:content-width="5in" src="/files/ftp_upload/51858/51858fig1highres.jpg" width="500" /> 
Figure 1. Lockable test tube used for transfer of samples. A)&#160;Flange for attachment to the cold inlet system,&#160;(B) Teflon tap of the test tube to enable transport of a compound under air-free conditions, (C)&#160;screw to operate the Teflon tap.
2. Measurement of Mass Spectra
<ol>
	<li>Prior to sample measurement, tune and calibrate the mass spectrometer according to the instructions supplied by the manufacturer of your mass spectrometer (here, an Autospec X (Vacuum Generators, now Waters Corp., Manchester, UK) is used.&#160;Use perflourokerosene (PFK) as a standard&#160;and tune the mass spectrometer to a resolution of ca. 2,800 at m/z 119, 10% valley definition). Remove the push rod of the direct inlet from the ion source and install the outer interface for the test tube (Figure 2). To prevent heating of the push rod tip, set the inlet method to &#8220;septum&#8221; in the control software of the mass spectrometer.</li>
	<li>Connect the flange of the lockable test tube filled with the sample to the outer interface. Open the needle valve of the outer interface and evacuate the inlet. After evacuation, carefully open the ball valve to the ion source to complete the evacuation step. Close the needle valve of the outer interface. CAUTION: The Teflon tap of the test tube has to be closed in this step.</li>
	<li>Start a mass measurement in the software of the mass spectrometer. With closed needle valve, open the Teflon tap of the test tube very briefly, allowing gas phase molecules of the analyte to enter the outer part of the interface. Close the Teflon tap again. 
	NOTE: The outer part of the interface together with the space between the Teflon tap and the flange of the lockable test tube (compare Figures 1 and 2B) serves as an analyte gas reservoir during the analysis.</li>
	<li>Carefully open the needle valve while observing the vacuum gauge of the ion source. This step allows analyte molecules to enter the ion source of the mass spectrometer. The vacuum should not fall below 10-5 mbar during the measurement. 
	NOTE: Depending on the volatility of the analyte mass spectra of good quality are obtained at approximately 10-6 mbar. The mass spectrum of the sample is now recorded. Usually, the sample amount leaking into the instrument through the needle valve is sufficient to record mass spectra for several minutes. In case the intensity of the ions decreases, opening the needle valve a little more allows for more acquisition time. If the quality of the mass spectra recorded at 70 eV is not satisfying, mass spectra can be recorded using lower kinetic energies of the electrons, e.g., 20 eV.</li>
</ol>
<img alt="Figure 2" fo:content-width="5in" src="/files/ftp_upload/51858/51858fig2highres.jpg" width="500" /> 
Figure 2. Cold inlet system with empty lockable test tube fitted to the ion source of a VG Autospec X. A)&#160;Lockable test tube, (B)&#160;flange connection between test tube an cold inlet system, (C)&#160;needle valve, (D)&#160;stainless steel plate with seal as connection to the ion source, (E)&#160;interface of the direct inlet, the ceramic tip of the push rod is visible.
3. After the Measurement
<ol>
	<li>Close the needle valve of the outer interface. Close the ball valve to the ion source. Stop the acquisition of mass spectra in the software.</li>
	<li>Evacuate the inlet system while opening the needle valve completely. Vent the interface while ball valve and needle valve are closed. Evacuate the interface again, open the needle valve during this step in order to remove residual sample vapor in the interface. Repeat this step at least 3x.</li>
	<li>Remove the lockable test tube from the interface. Continue with next sample or remove the outer interface from the flange of the ion source and replace it with the push rod.</li>
</ol>

<ol>
	<li>Field, F. H., Franklin, J. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Electron Impact phenomena and the Properties of Gaseous Ions Revised Edition. , (1957).</li><li>Schaeffer, O. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+Improved+Mass+Spectrometer+Ion+Source.">An Improved Mass Spectrometer Ion Source.</a> Rev. Sci. Instrum. 25, 660-662 (1954).</li><li>Yamashita, M., Fenn, J. B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Electrospray+Ion+Source+-+Another+Variation+of+the+Free-Jet+Theme.">Electrospray Ion Source - Another Variation of the Free-Jet Theme.</a> J. Phys. Chem. 88, 4451-4459 (1984).</li><li>Lubben, A. T., McIndoe, J. S., Weller, A. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Coupling+an+electrospray+ionization+mass+spectrometer+with+a+glovebox:+A+straightforward,+powerful,+and+convenient+combination+for+analysis+of+air-sensitive+organometallics.">Coupling an electrospray ionization mass spectrometer with a glovebox: A straightforward, powerful, and convenient combination for analysis of air-sensitive organometallics.</a> Organometallics. 27, 3303-3306 (2008).</li><li>Cooper, G. J. T., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Structural+and+Compositional+Control+in+{M12}+Cobalt+and+Nickel+Coordination+Clusters+Detected+Magnetochemically+and+with+Cryospray+Mass+Spectrometry.">Structural and Compositional Control in {M12} Cobalt and Nickel Coordination Clusters Detected Magnetochemically and with Cryospray Mass Spectrometry.</a> Angewandte Chemie International Edition. 46, 1340-1344 (2007).</li><li>Wang, W. S., Tseng, P. W., Chou, C. H., Shiea, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Detection+of+reactive+1,2,3-hexatriene-5-one+monomer+by+low-temperature+atmospheric+pressure+ionization+mass+spectrometry.">Detection of reactive 1,2,3-hexatriene-5-one monomer by low-temperature atmospheric pressure ionization mass spectrometry.</a> Rapid Communications in Mass Spectrometry. 12, 931-934 (1998).</li><li>Wang, C. H., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Detection+of+a+thermally+unstable+intermediate+in+the+Wittig+reaction+using+low-temperature+liquid+secondary+ion+and+atmospheric+pressure+ionization+mass+spectrometry.">Detection of a thermally unstable intermediate in the Wittig reaction using low-temperature liquid secondary ion and atmospheric pressure ionization mass spectrometry.</a> Journal of the American Society for Mass Spectrometry. 9, 1168-1174 (1998).</li><li>Eelman, M. D., Blacquiere, J. M., Moriarty, M. M., Fogg, D. E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Shining+new+light+on+an+old+problem:+Retooling+MALDI+mass+spectrometry+for+organotransition-metal+catalysis.">Shining new light on an old problem: Retooling MALDI mass spectrometry for organotransition-metal catalysis.</a> Angewandte Chemie-International Edition. 47, 303-306 (2008).</li><li>Linden, H. B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Liquid+injection+field+desorption+ionization:+a+new+tool+for+soft+ionization+of+samples+including+air-sensitive+catalysts+and+non-polar+hydrocarbons.">Liquid injection field desorption ionization: a new tool for soft ionization of samples including air-sensitive catalysts and non-polar hydrocarbons.</a> Eur. J. Mass Spectrom. 10, 459-468 (2004).</li><li>Gross, J. H., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Liquid+injection+field+desorption/ionization+of+reactive+transition+metal+complexes.">Liquid injection field desorption/ionization of reactive transition metal complexes.</a> Analytical and Bioanalytical Chemistry. 386, 52-58 (2006).</li><li>Peterson, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Mass+Spectrometer+All-Glass+Heated+Inlet.">Mass Spectrometer All-Glass Heated Inlet.</a> Analytical Chemistry. 34, 1850-1851 (1962).</li><li>Stafford, C., Morgan, T. D., Brunfeldt, R. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+mass+spectrometer+all-glass+heated+inlet.">A mass spectrometer all-glass heated inlet.</a> International Journal of Mass Spectrometry and Ion Physics. 1, 87-92 (1968).</li><li>Hayes, S. A., Berger, R. J. F., Mitzel, N. W., Bader, J., Hoge, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Chlorobis(pentafluoroethyl)phosphane:+Improved+Synthesis+and+Molecular+Structure+in+the+Gas+Phase.">Chlorobis(pentafluoroethyl)phosphane: Improved Synthesis and Molecular Structure in the Gas Phase.</a> Chemistry-a European Journal. 17, 3968-3976 (2011).</li><li>Zakharov, A. V., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Functionalized+Bis(pentafluoroethyl)phosphanes:+Improved+Syntheses+and+Molecular+Structures+in+the+Gas+Phase.">Functionalized Bis(pentafluoroethyl)phosphanes: Improved Syntheses and Molecular Structures in the Gas Phase.</a> European Journal of Inorganic Chemistry. , 3392-3404 (2013).</li></ol>

The authors have nothing to disclose.

The acquisition of mass spectra from compounds which decompose under standard sample preparation procedures is presented in this protocol. The presented technique is designed for the analysis of metal organyls, silanes and phosphane, which are highly susceptible to oxidation and/or hydrolysis, making it interesting especially for inorganic chemists. In order to achieve optimal results, vacuum or air-free conditions have to be preserved throughout the analysis. Therefore the protocol should be followed meticulously. In ca...

The analysis of compounds, such as metal organyls, silanes, or phosphanes by mass spectrometry is not always feasible. Several of these compounds are known to decompose rapidly when in contact with air. Therefore the most crucial steps when measuring mass spectra are sample preparation, the transfer of the analyte into the mass spectrometer and ion generation in the absence of air. In this protocol, we describe a strategy to meet these requirements and present an inlet system, which makes it possible to obtain mass spectra of volatile compounds previously not to be analyzed by mass spectrometry due to their difficult handling and rapid decomposition under ambient conditions. Thereby, unambiguous identification of novel or existing volatile metal organyls, silanes and phosphanes, susceptible to oxidation or hydrolysis, can now be performed with the assistance of mass spectrometry. There are two requirements which have to be met in order to analyze compounds which are susceptible to oxidation or hydrolysis: sample preparation and ion generation under inert conditions. The last premise can be easily met using a mass spectrometer with an ion source operating under vacuum. This is the case with most matrix-assisted-laser-desorption/ionization (MALDI) mass spectrometers and with all electron impact ionization (EI) mass spectrometers1,2. Electrospray ionization (ESI) is not readily compatible for the analysis of compounds susceptible to oxidation or hydrolysis, as the ionization process takes place under ambient conditions3. However, for some compounds which react not vigorously with oxygen or water, the drying and nebulizing gas with which most ESI sources are operated is sufficient for analysis by mass spectrometry4. This is also the case for Ionization strategies similar to ESI, e.g., low-temperature ESI, low-temperature atmospheric pressure ionization, and low-temperature liquid secondary ion mass spectrometry5-7. In contrast, sample preparation and transfer into the ion source under inert conditions is much more challenging. Both MALDI and ESI instruments have been coupled with glove boxes in order to enable sample preparation of compounds susceptible to oxidation and/or hydrolysis in an inert atmosphere4,8. The mass spectrometer is interfaced to the glove box either with a transfer capillary (ESI) or directly attached to the glove box (MALDI). The coupling of a glove box to a mass spectrometer via a transfer capillary would also be possible using another ionization strategy &#8211; liquid injection field desorption/ionization (LIFDI) &#8211; with which the analysis of sensitive compounds was reported9,10.
Additionally, MALDI and LIFDI are not suitable for the analysis of highly volatile compounds. MALDI requires the co-crystallization of the analyte with a matrix and LIFDI requires the deposition of the analyte onto an emitter from a solution. With both ionization strategies it is very likely that the analyte will evaporate along with the solvent. In contrast to MALDI instruments, EI mass spectrometers usually offer several methods for introducing the sample into the ion source: the direct inlet probe (small amounts of solids, oils, or waxes are deposited into an aluminum crucible which is introduced using a push rod), a septum inlet (for liquids), or coupling with a gas chromatograph. Again, at least part of the sample transfer takes place under ambient conditions and is difficult to perform under an inert atmosphere.
In the 1960&#8217;s, a sample inlet system was presented which enables the introduction of samples under vacuum into the ion source of an EI instrument &#8211; the all-glass heated inlet system (AGHIS)11,12. Here, the sample was located inside a sealed piece of glass capillary, which was inserted into the AGHIS. Subsequently, the AGHIS was evacuated and the glass container with the sample was broken. The AGHIS was then heated to evaporate the sample which reached the ion source of an EI mass spectrometer by means of a leak. When the glass capillary with the sample was prepared inside a glove box, the sample could be introduced into the mass spectrometer without any contact to air. However, the AGHIS is an apparatus which is not commercially available and difficult to assemble even for a skilled glassblower workshop. Due to the large dimensions switching between direct inlet using a push rod and AGHIS is not straight forward.
In our mass spectrometry lab, we developed a similar inlet system in the style of the AGHIS. However, as it is not possible to heat the inlet system, the analyte has to exhibit a certain volatility in order to enter the ion source of the mass spectrometer. The volatility of the analyte has to be sufficient, to allow for the transfer of the compound under vacuum at liquid nitrogen temperature &#8211; either by boiling or sublimation. The custom-made inlet system consists of a stainless steel plate, which is positioned at the direct inlet system, a stainless steel tube with a needle valve, and a flange, to which a lockable test tube containing the sample can be attached. The installation of the cold inlet system requires no modifications to the mass spectrometer (Autospec X, Vacuum Generators, now Waters Corp., Manchester, UK) &#8211; switching between cold inlet system and direct inlet using a push rod can be performed easily within seconds.
The presented inlet system is of particular use when metal organyls, silanes, or phosphanes, susceptible to oxidation or hydrolysis, have to be analyzed. These compounds are commonly analyzed using nuclear magnetic resonance (NMR) spectroscopy or&#160;infrared (IR) spectroscopy. Unfortunately, these methods allow not always for an unambiguous identification of a compound because they yield incomplete information, e.g., when elements such as chlorine or bromine are part of the molecule. Gas electron diffraction on the other hand is able to provide detailed information about the analyte, however, the method is very time consuming, sample preparation is difficult, and only few groups are able to conduct these analysis13,14. Here, the cold inlet system for the analysis of metal organyls, silanes, or phosphanes, susceptible to oxidation or hydrolysis by EI mass spectrometry is of great use for (in)organic chemists enabling the unambiguous identification of novel compounds by supplying them with information regarding the mass of a molecule and of characteristic fragment ions. The only prerequisite for the measurement of mass spectra for a substance is a certain volatility at reduced pressure.

<table border="0" cellpadding="0" cellspacing="0" width="971">
	<tbody>
		<tr height="21">
			<td height="21" style="height:21px;width:311px;">Name of Reagent/Material</td>
			<td style="width:71px;">Company</td>
			<td style="width:155px;">Catalog Number</td>
			<td style="width:435px;">Comments</td>
		</tr>
		<tr height="42">
			<td height="42" style="height:42px;width:311px;">VG Autospec X</td>
			<td colspan="2">Micromass Co. UK Ltd (now Waters)</td>
			<td style="width:435px;">other EI mass spectrometers with direct inlet using a push rod should also be compatible with this technique</td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:311px;">Lockable test tubes with flange</td>
			<td style="width:71px;">-</td>
			<td style="width:155px;">-</td>
			<td style="width:435px;">costum made, teflon tap should be used for locking the test tube</td>
		</tr>
		<tr height="42">
			<td height="42" style="height:42px;width:311px;">Interface for lockable test tubes</td>
			<td style="width:71px;">-</td>
			<td style="width:155px;">-</td>
			<td style="width:435px;">costum made , interface is prepared from stainless steel. Needle valve has to be included into the interface-design!</td>
		</tr>
		<tr height="63">
			<td height="63" style="height:63px;width:311px;">Schlenk line</td>
			<td style="width:71px;">-</td>
			<td style="width:155px;">-</td>
			<td style="width:435px;">costum made, has to include vacuum pump for evacuation of thest tubes and cold trap with liquid nitrogen for trapping of the sample</td>
		</tr>
	</tbody>
</table>

analysis of volatile and oxidation sensitive compounds using a cold inlet system and electron impact mass spectrometry

This video presents a protocol for the mass spectrometrical analysis of volatile and oxidation sensitive compounds using electron impact ionization. The analysis of volatile and oxidation sensitive compounds by mass spectrometry is not easily achieved, as all state-of-the-art mass spectrometric methods require at least one sample preparation step, e.g., dissolution and dilution of the analyte (electrospray ionization), co-crystallization of the analyte with a matrix compound (matrix-assisted laser desorption/ionization), or transfer of the prepared samples into the ionization source of the mass spectrometer, to be conducted under atmospheric conditions. Here, the use of a sample inlet system is described which enables the analysis of volatile metal organyls, silanes, and phosphanes using a sector field mass spectrometer equipped with an electron impact ionization source. All sample preparation steps and the sample introduction into the ion source of the mass spectrometer take place either under air-free conditions or under vacuum, enabling the analysis of compounds highly susceptible to oxidation. The presented technique is especially of interest for inorganic chemists, working with metal organyls, silanes, or phosphanes, which have to be handled using inert conditions, such as the Schlenk technique. The principle of operation is presented in this video.

An EI mass spectrum of tris(trifluoromethyl)phosphane is presented in Figure 3, a compound, which decomposes rapidly when in contact with air (Figure 4). The presented interface allows for the straight forward measurement of mass spectra for these compounds. The operation of the novel interface is easy and fast and presents no obstacle when operating the mass spectrometer with the routinely applied direct inlet using the push rod.
<p class="jove_content" fo:keep-together.within-page=...

Watch this Scientific Journal Video about Analysis of Volatile and Oxidation Sensitive Compounds Using a Cold Inlet System and Electron Impact Mass Spectrometry at JoVE.com

Analysis of Volatile and Oxidation Sensitive Compounds Using a Cold Inlet System and Electron Impact Mass Spectrometry

This video presents a protocol for the mass spectrometrical analysis of volatile and oxidation sensitive compounds using electron impact ionization. The presented technique is especially of interest for inorganic chemists, working with metal organyls, silanes, or phosphanes which have to be handled using inert conditions, such as the Schlenk technique.

This video presents a protocol for the mass spectrometrical analysis of volatile and oxidation sensitive compounds using electron impact ionization. The ...

analysis-volatile-oxidation-sensitive-compounds-using-cold-inlet

Research

JoVE Journal

Chemistry

9.6K Aufrufe.  Bielefeld University.  Dieses Video stellt ein Protokoll für die massenspektrometrische Analyse von flüchtigen und oxidationsempfindlichen Verbindungen mit Elektronenstoß-Ionisation. Das vorgestellte Verfahren ist insbesondere von Interesse für anorganische Chemie, die Arbeit mit Metallorganylen, Silane oder Phosphane, die mit inerten Bedingungen, wie der Schlenk-Technik behandelt werden müssen. 

Serie: Analysis of Volatile and Oxidation Sensitive Compounds Using a Cold Inlet System and Electron Impact Mass Spectrometry

Untargeted Metabolomics from Biological Sources Using Ultraperformance Liquid Chromatography-High Resolution Mass Spectrometry (UPLC-HRMS)

Here we present a workflow to analyze the metabolic profiles for biological samples of interest including; cells, serum, or tissue. The sample is first separated into polar and non-polar fractions by a liquid-liquid phase extraction, and partially purified to facilitate downstream analysis. Both aqueous (polar metabolites) and organic (non-polar metabolites) phases of the initial extraction are processed to survey a broad range of metabolites. Metabolites are separated by different liquid chromatography methods based upon their partition properties. In this method, we present microflow ultra-performance (UP)LC methods, but the protocol is scalable to higher flows and lower pressures. Introduction into the mass spectrometer can be through either general or compound optimized source conditions. Detection of a broad range of ions is carried out in full scan mode in both positive and negative mode over a broad m/z range using high resolution on a recently calibrated instrument. Label-free differential analysis is carried out on bioinformatics platforms. Applications of this approach include metabolic pathway screening, biomarker discovery, and drug development.

Untargeted Metabolomics from Biological Sources Using Ultraperformance Liquid Chromatography-High Resolution Mass Spectrometry UPLC-HRMS

Untargeted metabolomics provides a hypothesis generating snapshot of a metabolic profile. This protocol will demonstrate the extraction and analysis of metabolites from cells, serum, or tissue. A range of metabolites are surveyed using liquid-liquid phase extraction, microflow ultraperformance liquid chromatography/high-resolution mass spectrometry (UPLC-HRMS) coupled to differential analysis software.

Here we present a workflow to analyze the metabolic profiles for biological samples of interest including; cells, serum, or tissue. The sample is first ...

Visualization of Ambient Mass Spectrometry with the Use of Schlieren Photography

This manuscript outlines how to visualize mass spectrometry ambient ionization sources using schlieren photography. In order to properly optimize the mass spectrometer, it is necessary to characterize and understand the physical principles of the source. Most commercial ambient ionization sources utilize jets of nitrogen, helium, or atmospheric air to facilitate the ionization of the analyte. As a consequence, schlieren photography can be used to visualize the gas streams by exploiting the differences in refractive index between the streams and ambient air for visualization in real time. The basic setup requires a camera, mirror, flashlight, and razor blade. When properly configured, a real time image of the source is observed by watching its reflection. This allows for insight into the mechanism of action in the source, and pathways to its optimization can be elucidated. Light is shed on an otherwise invisible situation.

This paper presents a protocol for the visualization of gaseous streams of an ambient ionization source using schlieren photography and mass spectrometry.

This manuscript outlines how to visualize mass spectrometry ambient ionization sources using schlieren photography. In order to properly optimize the mass ...

Rapid High-throughput Species Identification of Botanical Material Using Direct Analysis in Real Time High Resolution Mass Spectrometry

We demonstrate that direct analysis in real time-high resolution mass spectrometry can be used to produce mass spectral profiles of botanical material, and that these chemical fingerprints can be used for plant species identification. The mass spectral data can be acquired rapidly and in a high throughput manner without the need for sample extraction, derivatization or pH adjustment steps. The use of this technique bypasses challenges presented by more conventional techniques including lengthy chromatography analysis times and resource intensive methods. The high throughput capabilities of the direct analysis in real time-high resolution mass spectrometry protocol, coupled with multivariate statistical analysis processing of the data, provide not only class characterization of plants, but also yield species and varietal information. Here, the technique is demonstrated with two psychoactive plant products, Mitragyna speciosa (Kratom) and Datura (Jimsonweed), which were subjected to direct analysis in real time-high resolution mass spectrometry followed by statistical analysis processing of the mass spectral data. The application of these tools in tandem enabled the plant materials to be rapidly identified at the level of variety and species.

A method for species identification of botanical material by direct analysis in real time-high resolution mass spectrometry and multivariate statistical analysis is presented.

We demonstrate that direct analysis in real time-high resolution mass spectrometry can be used to produce mass spectral profiles of botanical material, ...

Analyzing the Photo-oxidation of 2-propanol at Indoor Air Level Concentrations Using Field Asymmetric Ion Mobility Spectrometry

We demonstrate a versatile protocol to be used for determining the effectiveness of photocatalysts in degrading indoor air concentration (ppb) volatile organic carbons (VOCs), illustrating this with a titanium dioxide based catalyst, and the VOC 2-propanol. The protocol takes advantage of field asymmetric ion mobility spectroscopy (FAIMS), an analysis tool that is capable of continuously identifying and monitoring the concentration of VOCs such as 2-propanol and acetone at the ppb level. The continuous nature of FAIMS allows detailed kinetic analysis, and long-term reactions, offering a significant advantage over gas chromatography, a batch process traditionally used in air purification characterization. The use of FAIMS in photocatalytic air purification has only recently been used for the first time, and with the protocol illustrated here, the flexibility in allowing alternative VOCs and photocatalysts to be tested using comparable protocols offers a unique system to elucidate photocatalytic air purification reactions at low concentrations.

A protocol for determining the effectiveness of photocatalysts in degrading indoor air concentration (ppb) model volatile organic carbons such as 2-propanol is described.

We demonstrate a versatile protocol to be used for determining the effectiveness of photocatalysts in degrading indoor air concentration (ppb) volatile ...

Fizzy Extraction of Volatile Organic Compounds Combined with Atmospheric Pressure Chemical Ionization Quadrupole Mass Spectrometry

Chemical analysis of volatile and semivolatile compounds dissolved in liquid samples can be challenging. The dissolved components need to be brought to the gas phase, and efficiently transferred to a detection system. Fizzy extraction takes advantage of the effervescence phenomenon. First, a carrier gas (here, carbon dioxide) is dissolved in the sample by applying overpressure and stirring the sample. Second, the sample chamber is decompressed abruptly. Decompression leads to the formation of numerous carrier gas bubbles in the sample liquid. These bubbles assist the release of the dissolved analyte species from the liquid to the gas phase. The released analytes are immediately transferred to the atmospheric pressure chemical ionization interface of a triple quadrupole mass spectrometer. The ionizable analyte species give rise to mass spectrometric signals in the time domain. Because the release of the analyte species occurs over short periods of time (a few seconds), the temporal signals have high amplitudes and high signal-to-noise ratios. The amplitudes and areas of the temporal peaks can then be correlated with concentrations of the analytes in the liquid samples subjected to fizzy extraction, which enables quantitative analysis. The advantages of fizzy extraction include: simplicity, speed, and limited use of chemicals (solvents).

Fizzy extraction is a new laboratory technique for analysis of volatile and semivolatile compounds. A carrier gas is dissolved in the liquid sample by applying overpressure and stirring the sample. The sample chamber is then decompressed. The analyte species are liberated to the gas phase due to effervescence.

Chemical analysis of volatile and semivolatile compounds dissolved in liquid samples can be challenging. The dissolved components need to be brought to ...

Real-time Breath Analysis by Using Secondary Nanoelectrospray Ionization Coupled to High Resolution Mass Spectrometry

Exhaled volatile organic compounds (VOCs) have aroused considerable interest, since they can serve as biomarkers for disease diagnosis and environmental exposure in a non-invasive manner. In this work, we present a protocol to characterize the exhaled VOCs in real time by using secondary nanoelectrospray ionization coupled to high resolution mass spectrometry (Sec-nanoESI-HRMS). The homemade Sec-nanoESI source was readily set up based on a commercial nanoESI source. Hundreds of peaks were observed in the background-subtracted mass spectra of exhaled breath, and the mass accuracy values are -4.0-13.5 ppm and -20.3-1.3 ppm in the positive and negative ion detection modes, respectively. The peaks were assigned with accurate elemental composition according to the accurate mass and isotopic pattern. Less than 30 s is used for one exhalation measurement, and it takes approximately 7 min for six replicated measurements.

A protocol for characterizing chemical composition of exhaled breath in real time by using secondary nanoelectrospray ionization coupled to high resolution mass spectrometry is demonstrated.

Exhaled volatile organic compounds (VOCs) have aroused considerable interest, since they can serve as biomarkers for disease diagnosis and environmental ...

Synthesis and Mass Spectrometry Analysis of Oligo-peptoids

Peptoids are sequence-controlled peptide-mimicking oligomers consisting of N-alkylated glycine units. Among many potential applications, peptoids have been thought of as a type of molecular information storage. Mass spectrometry analysis has been considered the method of choice for sequencing peptoids. Peptoids can be synthesized via solid phase chemistry using a repeating two-step reaction cycle. Here we present a method to manually synthesize oligo-peptoids and to analyze the sequence of the peptoids using tandem mass spectrometry (MS/MS) techniques. The sample peptoid is a nonamer consisting of alternating N-(2-methyloxyethyl)glycine (Nme) and N-(2-phenylethyl)glycine (Npe), as well as an N-(2-aminoethyl)glycine (Nae) at the N-terminus. The sequence formula of the peptoid is Ac-Nae-(Npe-Nme)4-NH2, where Ac is the acetyl group. The synthesis takes place in a commercially available solid-phase reaction vessel. The rink amide resin is used as the solid support to yield the peptoid with an amide group at the C-terminus. The resulting peptoid product is subjected to sequence analysis using a triple-quadrupole mass spectrometer coupled to an electrospray ionization source. The MS/MS measurement produces a spectrum of fragment ions resulting from the dissociation of charged peptoid. The fragment ions are sorted out based on the values of their mass-to-charge ratio (m/z). The m/z values of the fragment ions are compared against the nominal masses of theoretically predicted fragment ions, according to the scheme of peptoid fragmentation. The analysis generates a fragmentation pattern of the charged peptoid. The fragmentation pattern is correlated to the monomer sequence of the neutral peptoid. In this regard, MS analysis reads out the sequence information of the peptoids.

A protocol is described for the manual synthesis of oligo-peptoids followed by sequence analysis by mass spectrometry.

Peptoids are sequence-controlled peptide-mimicking oligomers consisting of N-alkylated glycine units. Among many potential applications, peptoids have ...

High-throughput and Comprehensive Drug Surveillance Using Multisegment Injection-Capillary Electrophoresis-Mass Spectrometry

New analytical methods are urgently needed to enable high-throughput, yet comprehensive drug screening, given an alarming opioid and prescription drug crisis in public health. Conventional urine drug testing based on a two-tier immunoassay screen followed by a gas chromatography-tandem mass spectrometry (GC-MS/MS) or liquid chromatography-tandem mass spectrometry (LC-MS/MS) method are expensive and prone to bias while being limited to targeted panels of known drugs of abuse (DoA). Herein, we outline an improved method for drug surveillance that allows for the resolution and detection of an expanded panel of DoA and their metabolites when using multisegment injection-capillary electrophoresis-mass spectrometry (MSI-CE-MS). Multiplexed separations of ten urine samples with a quality control by CE (&lt; 3 min/sample) in conjunction with full-scan data acquisition using a time-of-flight mass spectrometer (TOF-MS) under positive ion mode detection allows for the identification and quantification of DoA above recommended cut-off levels. An excellent resolution of drug isomers and isobars, including background interferences, are achieved when using MSI-CE-MS with an electrokinetic spacer between sample segments, where accurate mass/molecular formula together with the comigration of a matching deuterated internal standard and the detection of one or more bio-transformed metabolites facilitate DoA identification over a wider detection window. Additionally, urine samples can be analyzed directly without enzyme deconjugation for the rapid screening without complicated sample workup. MSI-CE-MS enables the surveillance of a broad spectrum of DoA that is required for the treatment monitoring of high-risk patients, including confirming prescribed drug adherence, revealing illicit drug use/substitution, and evaluating optimal dosage regimes as required for new advances in precision medicine.

Here we describe a high-throughput method for comprehensive drug surveillance that allows for the improved resolution and detection of large panels of drugs of abuse and their metabolites, with quality control based on multisegment injection-capillary electrophoresis-mass spectrometry.

New analytical methods are urgently needed to enable high-throughput, yet comprehensive drug screening, given an alarming opioid and prescription drug ...

Ion Mobility-Mass Spectrometry Techniques for Determining the Structure and Mechanisms of Metal Ion Recognition and Redox Activity of Metal Binding Oligopeptides

Electrospray ionization (ESI) can transfer an aqueous-phase peptide or peptide complex to the gas-phase while conserving its mass, overall charge, metal-binding interactions, and conformational shape. Coupling ESI with ion mobility-mass spectrometry (IM-MS) provides an instrumental technique that allows for simultaneous measurement of a peptide&#8217;s mass-to-charge (m/z) and collision cross section (CCS) that relate to its stoichiometry, protonation state, and conformational shape. The overall charge of a peptide complex is controlled by the protonation of 1) the peptide&#8217;s acidic and basic sites and 2) the oxidation state of the metal ion(s). Therefore, the overall charge state of a complex is a function of the pH of the solution that affects the peptides metal ion binding affinity. For ESI-IM-MS analyses, peptide and metal ions solutions are prepared from aqueous-only solutions, with the pH adjusted with dilute aqueous acetic acid or ammonium hydroxide. This allows for pH dependence and metal ion selectivity to be determined for a specific peptide. Furthermore, the m/z and CCS of a peptide complex can be used with B3LYP/LanL2DZ molecular modeling to discern binding sites of the metal ion coordination and tertiary structure of the complex. The results show how ESI-IM-MS can characterize the selective chelating performance of a set of alternative methanobactin peptides and compare them to the copper-binding peptide methanobactin.

Ion mobility-mass spectrometry and molecular modeling techniques can characterize the selective metal chelating performance of designed metal-binding peptides and the copper-binding peptide methanobactin. Developing new classes of metal chelating peptides will help lead to therapeutics for diseases associated with metal ion misbalance.

Electrospray ionization (ESI) can transfer an aqueous-phase peptide or peptide complex to the gas-phase while conserving its mass, overall charge, ...

Capillary Electrophoresis-based Hydrogen/Deuterium Exchange for Conformational Characterization of Proteins with Top-down Mass Spectrometry

Resolving conformational heterogeneity of multiple protein states that coexist in solution remains one of the main obstacles in the characterization of protein therapeutics and the determination of the conformational transition pathways critical for biological functions, ranging from molecular recognition to enzymatic catalysis. Hydrogen/deuterium exchange (HDX) reaction coupled with top-down mass spectrometric (MS) analysis provides a means to characterize protein higher-order structures and dynamics in a conformer-specific manner. The conformational resolving power of this technique is highly dependent on the efficiencies of separating protein states at the intact protein level and minimizing the residual non-deuterated protic content during the HDX reactions. 
Here we describe a capillary electrophoresis (CE)-based variant of the HDX MS approach that aims to improve the conformational resolution. In this approach, proteins undergo HDX reactions while migrating through a deuterated background electrolyte solution (BGE) during the capillary electrophoretic separation. Different protein states or proteoforms that coexist in solution can be efficiently separated based on their differing charge-to-size ratios. The difference in electrophoretic mobility between proteins and protic solvent molecules minimizes the residual non-deuterated solvent, resulting in a nearly complete deuterating environment during the HDX process. The flow-through microvial CE-MS interface allows efficient electrospray ionization of the eluted protein species following a rapid mixing with the quenching and denaturing modifier solution at the outlet of the sprayer. The online top-down MS analysis measures the global deuteration level of the eluted intact protein species, and subsequently, the deuteration of their gas-phase fragments. This paper demonstrates this approach in differential HDX for systems, including the natural protein variants coexisting in milk.

Presented here is a protocol for a capillary electrophoresis-based hydrogen/deuterium exchange (HDX) approach coupled with top-down mass spectrometry. This approach characterizes the difference in higher-order structures between different protein species, including proteins in different states and different proteoforms, by conducting concurrent differential HDX and electrophoretic separation.

Resolving conformational heterogeneity of multiple protein states that coexist in solution remains one of the main obstacles in the characterization of ...