Supported by Career Development Award from Research to Prevent Blindness, NIH grant EY 019312, and unrestricted grant from Research to Prevent Blindness and EY 02687 (Department of Ophthalmology &amp; Visual Sciences at Washington University).

Making electrodes
<ol>
 <li>Make the recording electrodes using a micropipette puller and polish the electrodes with heating filament under microscope. For mouse cone single-cell suction recording, the inner diameter on the electrode tip is about 6-7 &mu;m.</li>
 <li>Prepare reference electrodes. Weigh 1% agar in distilled water. Melt the agar solution in hot water bath. Fill the glass pipettes (L = 100 mm, OD/ID = 1/0.75 mm) with 1% agar using syringe. Solidify the agar at room temperature for 10 minutes.</li>
 <li>Cut the pipettes into halves using a diamond knife.</li>
 <li>Soak the reference electrodes in reference solution for at least 24 hours at 4 &deg;C.</li>
</ol>
Setting up the experiment
<ol start="5">
 <li>Dark adapt a mouse in a black cage overnight.</li>
 <li>Prepare 100 mL reference solution and 1 L perfusion solution (see below) and filter the solution.</li>
 <li>Dissolve 0.1% BSA and 10 mM Glucose in 20 mL reference solution.</li>
 <li>Calibrate the light intensity of the optical stimulator using photometer.</li>
 <li>Mount the recording chamber on the stage of the inverted microscope.</li>
 <li>Bubble the perfusion solution with 95% O2/5% CO2, incubate it in 40 &deg;C water bath to increase the solubility of CO2. The solution flows from the bottle to the recording chamber passing through a ceramic resistor warming it to 36-38 &deg;C. The heater should be located as close to the recording chamber as possible, ideally at the stage of the microscope.</li>
 <li>Adjust the flow regulator for a flow rate of about 1-1.5 mL/min.</li>
 <li>Fill the recording electrode with reference solution. Insert the electrode in an electrode holder. Make sure there are no bubbles in the electrode. Mount the holder on the headstage of the amplifier. Connect the holder to a suction device, which is built by connecting tubing partially filled with mineral oil to the side-port of the electrode holder. The other end of the tubing is connected to a small reservoir of mineral oil, to which pressure can be applied by mouth. </li>
 <li>Connect the reference electrode to the other pole of the headstage. Bind the thermal couple (TC) to the reference electrode. Make sure the electrode and TC tips are close together so that the temperature reading is taken as close to the cell as possible. </li>
 <li>Turn on the infrared illumination to visualize the electrode. The electrode is viewed by infrared camera connected to a monitor. Center the electrode image on the visual field and of the monitor using a micro-manipulator. </li>
 <li>Adjust the position of the reference electrode tip close (2-4 mm) to the recording electrode tip.</li>
 <li>Adjust the DC voltage for the heater so that the temperature of the solution is about 36-38 &deg;C.</li>
 <li>Run a seal test to check the resistance of recording electrode, normally about 900 k&Omega;.</li>
</ol>
Isolating the mouse retina
<ol start="18">
 <li>Under dim red light, euthanize the dark-adapted mouse with CO2 and cervical dislocation. Mark the eyeballs using the tip of a hot metal torch by cauterizing the most dorsal point of the sclera slightly. Enucleate the eyeballs using scissors. All subsequent procedures are performed under infrared light.</li>
 <li>Hemisect the eyeballs under microscope with infrared illumination and image converters. </li>
 <li>Remove the cornea and lens. Remove as much of the vitreous as possible.</li>
 <li>To record M-cone responses, remove the ventral part of the eyecup 4 with a razor blade judging from the cautery mark.</li>
 <li>Peel the retina from the pigment epithelium layer.</li>
 <li>Flatten the retina and place it on the bottom of the Petri dish filled with 1-2 mL reference solution.</li>
 <li>Slice the retina into small thin pieces using a razor blade and incubate the preparation in a light-tight box saturated with pure oxygen.</li>
</ol>
Recordings
<ol start="25">
 <li>Turn off the heater temporarily. Switch the perfusion flow to a bypass tubing to prevent the chamber from drying.</li>
 <li>Drain most of the solution in the chamber using a piece of Kimwipe tissue. Transfer the retina suspension to the recording chamber using a glass pipette.</li>
 <li>Wait for about 2 minutes until the retina slices settle down. Switch the perfusion back on. Turn on the heater.</li>
 <li>Turn on infrared illumination to visualize the preparation. Search for a piece of retina lying on the chamber with photoreceptor outer segments sticking out (see example figure). Draw inner segments gently into the electrode by suction. In this configuration, several nuclei and inner segments should be drawn into the electrode. Record the photoresponse to a bright flash to test whether a cone inner segment is in the electrode and whether the cell is healthy, judging by the response kinetics and amplitude. </li>
 <li>Lower the mineral reservoir to apply slight negative pressure to the tip of the electrode to help hold the inner segment in the electrode. </li>
 <li>Record test-flash responses from dim to bright intensity once a good cell is found. Test flashes are provided from a calibrated optical stimulator 5. Flash intensity and wavelength are controlled by a set of neutral density filters and narrow band interference filters, respectively. Test flash duration (20 ms) is controlled by computer-driven shutters.</li>
 </ol>
Solutions
<ol>
 <li>Mouse perfusion solution: 112.5 mM NaCl, 3.6 mM KCl, 2.4 mM MgCl2, 1.2 mM CaCl2, 10 mM HEPES (pH 7.4), 20 mM NaHCO3, 3 mM Na succinate, 0.5 mM Na glutamate, 0.02 mM EDTA, and 10 mM glucose.</li>
 <li>Mouse recording electrode solution: 140 mM NaCl, 3.6 mM KCl, 2.4 mM MgCl2, 1.2 mM CaCl2, 3 mM HEPES (pH 7.4), 0.02 mM EDTA.</li>
</ol>

<ol>
	<li>Yau, K. W., Lamb, T. D., Baylor, D. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Light-induced+fluctuations+in+membrane+current+of+single+toad+rod+outer+segments.">Light-induced fluctuations in membrane current of single toad rod outer segments.</a> Nature. 269, 78-80 (1977).</li><li>Nikonov, S. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Photoreceptors+of+Nrl+-/-+mice+coexpress+functional+S-+and+M-cone+opsins+having+distinct+inactivation+mechanisms.">Photoreceptors of Nrl -/- mice coexpress functional S- and M-cone opsins having distinct inactivation mechanisms.</a> J Gen Physiol. 125, 287-304 (2005).</li><li>Nikonov, S. S., Kholodenko, R., Lem, J., Pugh, E. N. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Physiological+features+of+the+S-+and+M-cone+photoreceptors+of+wild-type+mice+from+single-cell+recordings.">Physiological features of the S- and M-cone photoreceptors of wild-type mice from single-cell recordings.</a> J Gen Physiol. 127, 359-374 (2006).</li><li>Applebury, M. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+murine+cone+photoreceptor:+a+single+cone+type+expresses+both+S+and+M+opsins+with+retinal+spatial+patterning.">The murine cone photoreceptor: a single cone type expresses both S and M opsins with retinal spatial patterning.</a> Neuron. 27, 513-523 (2000).</li><li>Cornwall, M. C., Fein, A., MacNichol, E. F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Cellular+mechanisms+that+underlie+bleaching+and+background+adaptation.">Cellular mechanisms that underlie bleaching and background adaptation.</a> J Gen Physiol. 96, 345-372 (1990).</li><li>Calvert, P. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Phototransduction+in+transgenic+mice+after+targeted+deletion+of+the+rod+transducin+alpha+-subunit.">Phototransduction in transgenic mice after targeted deletion of the rod transducin alpha -subunit.</a> Proc Natl Acad Sci U S A. 97, 13913-13918 (2000).</li></ol>

Single-cell suction recording from photoreceptor cells was developed 3 decades ago. It enables us to record trans-membrane current change induced by light stimulation without penetrating the cell membrane. Because of high cell-cell adhesion, it is difficult to isolate healthy single rod and cone from mouse retina like amphibian retina and it is hard to find individual cones due to the low percentage (3%) and small size. The inner-segment-in (IS-in) recording method overcomes this difficulty by recording current from the ...

single-cell suction recordings from mouse cone photoreceptors

Rod and cone photoreceptors in the retina are responsible for light detection. In darkness, cyclic nucleotide-gated (CNG) channels in the outer segment are open and allow cations to flow steadily inwards across the membrane, depolarizing the cell. Light exposure triggers the closure of the CNG channels, blocks the inward cation current flow, and thus results in cell hyperpolarization. Based on the polarity of photoreceptors, a suction recording method was developed in 1970s that, unlike the classic patch-clamp technique, does not require penetrating the plasma membrane 1. Drawing the outer segment into a tightly-fitting glass pipette filled with extracellular solution allows recording the current changes in individual cells upon test-flash exposure. However, this well-established "outer-segment-in (OS-in)" suction recording is not suitable for mouse cone recordings, because of the low percentage of cones in the mouse retina (3%) and the difficulties in identifying the cone outer segments. Recently, an inner-segment-in (IS-in) recording configuration was developed to draw the inner segment/nuclear region of the photoreceptor into the recording pipette 2,3. In this video, we will show how to record from individual mouse cone photoresponses using single-cell suction electrode.

Watch this Scientific Journal Video about Single-cell Suction Recordings from Mouse Cone Photoreceptors at JoVE.com

Single-cell Suction Recordings from Mouse Cone Photoreceptors

We will show how to record flash responses from single mouse cones using a suction electrode.

Rod and cone photoreceptors in the retina are responsible for light detection. In darkness, cyclic nucleotide-gated (CNG) channels in the outer segment ...

single-cell-suction-recordings-from-mouse-cone-photoreceptors

Research

JoVE Journal

Biology

11.7K vistas.  Washington University in St. Louis, School of Medicine. Le mostraremos cómo registrar las respuestas de flash de conos ratón utilizando un electrodo de succión.

Video: Single-cell Suction Recordings from Mouse Cone Photoreceptors

Whole Cell Recordings from Brain of Adult Drosophila

In this video, we demonstrate the procedure for isolating whole brains from adult Drosophila in preparation for recording from single neurons. We begin by describing the dissecting solution and capture of the adult females used in our studies. The procedure for removing the whole brain intact, including both optic lobes, is illustrated. Dissection of the overlying trachea is also shown.  The isolated brain is not only small but needs special care in handling at this stage to prevent damage to the neurons, many of which are close to the outer surface of the tissue. We show how a special holder we developed is used to stabilize the brain in the recording chamber. A standard electrophysiology set up is used for recording from single neurons or pairs of neurons. A fluorescent image, viewed through the recording microscope, from a GAL4 line driving GFP expression (GH146) illustrates how projection neurons (PNs) are identified in the live brain. A high power Nomarski image shows a view of a single neuron that is being targeted for whole cell recording. When the brain is successfully removed without damage, the majority of the neurons are spontaneously active, firing action potentials and/or exhibiting spontaneous synaptic input. This in situ preparation, in which whole cell recording of identified neurons in the whole brain can be combined with genetic and pharmacological manipulations, is a useful model for exploring cellular physiology and plasticity in the adult CNS.

This video demonstrates the procedure for isolating whole brains from adult Drosophila in preparation for recording from single neurons using standard whole cell technology. It includes images of GFP labeled cells and neurons viewed during recording.

In this video, we demonstrate the procedure for isolating whole brains from adult Drosophila in preparation for recording from single neurons. We begin by ...

Preparation of Single-Cell Suspensions from Mouse Spleen with the gentleMACS Dissociator

Single-cell suspensions are a prerequisite for experiments in cell separation, cell analysis and cell culture.  To avoid tedious and often painful manual dissociations the gentleMACS Dissociator allows one to dissociate tissue very efficiently under controlled and reproducible conditions.  The gentleMACS Dissociator can optimally dissociate mouse spleen, combining timesaving and standardization with user-safety.

This video describes how to dissociate mouse spleens using the gentleMACS Dissociator, an automated bench-top device that can mechanically disrupt tissues using special tubes to produce viable cell suspensions. Following dissociation, spleens are filtered, centrifuged, and resuspended for further applications.

This video describes a simple, time-saving technique for automated tissue dissociation using the gentleMACS Dissociator to prepare single-cell suspensions of mouse splenocytes.

Single-cell suspensions are a prerequisite for experiments in cell separation, cell analysis and cell culture.  To avoid tedious and often painful manual ...

Standardized Preparation of Single-Cell Suspensions from Mouse Lung Tissue using the gentleMACS Dissociator

The preparation of single-cell suspensions from tissues is an important prerequisite for many experiments in cellular research. The process of dissociating whole organs requires specific parameters in order to obtain a high number of viable cells in a reproducible manner. The gentleMACS Dissociator optimizes this task with a simple, practical protocol. The instrument contains pre-programmed settings that are optimized for the efficient but gentle dissociation of a variety of tissue types, including mouse lungs. In this publication the use of the gentleMACS Dissociator on lung tissue derived from mice is demonstrated.

Dissociating cells from specific tissue types requires specific parameters for tissue agitation to obtain a high volume of viable, culturable cells. The Miltenyi gentleMACS dissociator optimizes this task with a simple, practical protocol. In this publication the use of this apparatus on lung tissue is explained.

The preparation of single-cell suspensions from tissues is an important prerequisite for many experiments in cellular research. The process of ...

Generation of Single-Cell Suspensions from Mouse Neural Tissue

Within the nervous system, hundreds of neuronal and glial cell types have been described. Each specific cell type in the brain or spinal cord has a repertoire of cell surface molecules, or molecular determinants, through which it can be identified and characterized. Currently, robust cell identification and separation technologies require single-cell preparations to be generated while simultaneously limiting cell death and destruction of characteristic surface protein. The gentleMACS Dissociator, when used in combination with trypsin or papain-based dissociation kits, can effectively and gently dissociate brain tissue while preserving antigen epitopes and limiting cell loss. Standardized preparation of single-cell suspensions is achieved using C Tubes and optimized, preset gentleMACS Programs. Once generated, single-cell suspensions can be treated with monoclonal conjugates like Anti-Prominin-1 MicroBeads, which identify neural progenitors, or purified further using Myelin Removal Beads.

Dissociating cells from specific tissue types requires specific parameters for tissue aggitation to obtain a high volume of viable, culturable cells. The Miltenyi gentleMACS Dissociator optimizes this task with a simple, practical protocol. In this publication the use of this apparatus on nerual tissue is explained.

Within the nervous system, hundreds of neuronal and glial cell types have been described. Each specific cell type in the brain or spinal cord has a ...

Single Cell Transcriptional Profiling of Adult Mouse Cardiomyocytes

While numerous studies have examined gene expression changes from homogenates of heart tissue, this prevents studying the inherent stochastic variation between cells within a tissue. Isolation of pure cardiomyocyte populations through a collagenase perfusion of mouse hearts facilitates the generation of single cell microarrays for whole transcriptome gene expression, or qPCR of specific targets using nanofluidic arrays. We describe here a procedure to examine single cell gene expression profiles of cardiomyocytes isolated from the heart. This paradigm allows for the evaluation of metrics of interest which are not reliant on the mean (for example variance between cells within a tissue) which is not possible when using conventional whole tissue workflows for the evaluation of gene expression (Figure 1). We have achieved robust amplification of the single cell transcriptome yielding micrograms of double stranded cDNA that facilitates the use of microarrays on individual cells. In the procedure we describe the use of NimbleGen arrays which were selected for their ease of use and ability to customize their design. Alternatively, a reverse transcriptase - specific target amplification (RT-STA) reaction, allows for qPCR of hundreds of targets by nanofluidic PCR. Using either of these approaches, it is possible to examine the variability of expression between cells, as well as examining expression profiles of rare cell types from within a tissue. Overall, the single cell gene expression approach allows for the generation of data that can potentially identify idiosyncratic expression profiles that are typically averaged out when examining expression of millions of cells from typical homogenates generated from whole tissues.

Single cell expression profiling allows the detailed gene expression analysis of individual cells. We describe methods for the isolation of cardiomyocytes, and preparing the resulting lysates for either whole transcriptome microarray or qPCR of specific targets.

While numerous studies have examined gene expression changes from homogenates of heart tissue, this prevents studying the inherent stochastic variation ...

Generation of Mice Derived from Induced Pluripotent Stem Cells

The production of induced pluripotent stem cells (iPSCs) from somatic cells provides a means to create valuable tools for basic research and may also produce a source of patient-matched cells for regenerative therapies. iPSCs may be generated using multiple protocols and derived from multiple cell sources. Once generated, iPSCs are tested using a variety of assays including immunostaining for pluripotency markers, generation of three germ layers in embryoid bodies and teratomas, comparisons of gene expression with embryonic stem cells (ESCs) and production of chimeric mice with or without germline contribution2. Importantly, iPSC lines that pass these tests still vary in their capacity to produce different differentiated cell types2. This has made it difficult to establish which iPSC derivation protocols, donor cell sources or selection methods are most useful for different applications.
The most stringent test of whether a stem cell line has sufficient developmental potential to generate all tissues required for survival of an organism (termed full pluripotency) is tetraploid embryo complementation (TEC)3-5. Technically, TEC involves electrofusion of two-cell embryos to generate tetraploid (4n) one-cell embryos that can be cultured in vitro to the blastocyst stage6. Diploid (2n) pluripotent stem cells (e.g. ESCs or iPSCs) are then injected into the blastocoel cavity of the tetraploid blastocyst and transferred to a recipient female for gestation (see Figure 1). The tetraploid component of the complemented embryo contributes almost exclusively to the extraembryonic tissues (placenta, yolk sac), whereas the diploid cells constitute the embryo proper, resulting in a fetus derived entirely from the injected stem cell line.
Recently, we reported the derivation of iPSC lines that reproducibly generate adult mice via TEC1. These iPSC lines give rise to viable pups with efficiencies of 5-13%, which is comparable to ESCs3,4,7 and higher than that reported for most other iPSC lines8-12. These reports show that direct reprogramming can produce fully pluripotent iPSCs that match ESCs in their developmental potential and efficiency of generating pups in TEC tests. At present, it is not clear what distinguishes between fully pluripotent iPSCs and less potent lines13-15. Nor is it clear which reprogramming methods will produce these lines with the highest efficiency. Here we describe one method that produces fully pluripotent iPSCs and "all- iPSC" mice, which may be helpful for investigators wishing to compare the pluripotency of iPSC lines or establish the equivalence of different reprogramming methods.

Generating induced pluripotent stem cell (iPSC) lines produces lines of differing developmental potential even when they pass standard tests for pluripotency. Here we describe a protocol to produce mice derived entirely from iPSCs, which defines the iPSC lines as possessing full pluripotency1.

The production of induced pluripotent stem cells (iPSCs) from somatic cells provides a means to create valuable tools for basic research and may also ...

Trans-inner Cell Mass Injection of Embryonic Stem Cells Leads to Higher Chimerism Rates

In an effort to increase efficiency in the creation of genetically modified mice via ES Cell methodologies, we present an adaptation to the current blastocyst injection protocol. Here we report that a simple rotation of the embryo, and injection through Trans-Inner cell mass (TICM) increased the percentage of chimeric mice from 31% to 50%, with no additional equipment or further specialized training. 26 different inbred clones, and 35 total clones were injected over a period of 9 months. There was no significant difference in either pregnancy rate or recovery rate of embryos between traditional injection techniques and TICM. Therefore, without any major alteration in the injection process and a simple positioning of the blastocyst and injecting through the ICM, releasing the ES cells into the blastocoel cavity can potentially improve the quantity of chimeric production and subsequent germline transmission.

Here we present a protocol to increase chimera production without the use of new equipment. A simple orientation change of the embryo for injection can increase the number of embryos produced, and potentially reduce the timeline to germline transmission.

In an effort to increase efficiency in the creation of genetically modified mice via ES Cell methodologies, we present an adaptation to the current ...

Isolation of Endothelial Cells from the Lumen of Mouse Carotid Arteries for Single-Cell Multi-Omics Experiments

Atherosclerosis is an inflammatory disease of the arterial regions exposed to disturbed blood flow (d-flow). D-flow regulates the expression of genes in the endothelium at the transcriptomic and epigenomic levels, resulting in proatherogenic responses. Recently, single-cell RNA sequencing (scRNAseq) and single-cell Assay for Transposase Accessible Chromatin sequencing (scATACseq) studies were performed to determine the transcriptomic and chromatin accessibility changes at a single-cell resolution using the mouse partial carotid ligation (PCL) model. As endothelial cells (ECs) represent a minor fraction of the total cell populations in the artery wall, a luminal digestion method was used to obtain EC-enriched single-cell preparations. For this study, mice were subjected to PCL surgery to induce d-flow in the left carotid artery (LCA) while using the right carotid artery (RCA) as a control. The carotid arteries were dissected out two days or two weeks post PCL surgery. The lumen of each carotid was subjected to collagenase digestion, and endothelial-enriched single cells or single nuclei were obtained. These single-cell and single-nuclei preparations were subsequently barcoded using a 10x Genomics microfluidic setup. The barcoded single-cells and single-nuclei were then utilized for RNA preparation, library generation, and sequencing on a high-throughput DNA sequencer. Post bioinformatics processing, the scRNAseq and scATACseq datasets identified various cell types from the luminal digestion, primarily consisting of ECs. Smooth muscle cells, fibroblasts, and immune cells were also present. This EC-enrichment method aided in understanding the effect of blood flow on the endothelium, which could have been difficult with the total artery digestion method. The EC-enriched single-cell preparation method can be used to perform single-cell omics studies in EC-knockouts and transgenic mice where the effect of blood flow on these genes has not been studied. Importantly, this technique can be adapted to isolate EC-enriched single cells from human artery explants to perform similar mechanistic studies.

We present a method for isolating endothelial cells and nuclei from the lumen of mouse carotid arteries exposed to stable or disturbed flow conditions to perform single-cell omics experiments.

Atherosclerosis is an inflammatory disease of the arterial regions exposed to disturbed blood flow (d-flow). D-flow regulates the expression of genes in ...

Single-Cell Suspension Preparation from Nile Tilapia Intestine for Single-Cell Sequencing

Nile tilapia is one of the most commonly cultured freshwater fish species worldwide and is a widely used research model for aquaculture fish studies. The preparation of high-quality single-cell suspensions is essential for single-cell level studies such as single-cell RNA or genome sequencing. However, there is no ready-to-use protocol for aquaculture fish species, particularly for the intestine of tilapia. The effective dissociation enzymes vary depending on the tissue type. Therefore, optimizing the tissue dissociation protocol by selecting the appropriate enzyme or enzyme combination to obtain enough viable cells with minimum damage is essential. This study illustrates an optimized protocol to prepare a high-quality single-cell suspension from Nile tilapia intestine with an enzyme combination of collagenase/dispase. This combination is highly effective for dissociation with the utilization of bovine serum albumin and DNase to reduce cell aggregation after digestion. The cell output satisfies the requirements for single-cell sequencing, with 90% cell viability and a high cell concentration. This protocol can also be modified to prepare a single-cell suspension from the intestines of other fish species. This research provides an efficient reference protocol and reduces the need for additional trials in the preparation of single-cell suspensions for aquaculture fish species.

Here, we demonstrate the preparation of a high-quality single-cell suspension of tilapia intestine for single-cell sequencing.

Nile tilapia is one of the most commonly cultured freshwater fish species worldwide and is a widely used research model for aquaculture fish studies. The ...

Isolation and Transcriptome Analysis of Plant Cell Types

In multicellular organisms, developmental programming and environmental responses can be highly divergent in different cell types or even within cells, which is known as cellular heterogeneity. In recent years, single-cell and cell-type isolation combined with next-generation sequencing (NGS) techniques have become important tools for studying biological processes at single-cell resolution. However, isolating plant cells is relatively more difficult due to the presence of plant cell walls, which limits the application of single-cell approaches in plants. This protocol describes a robust procedure for fluorescence-activated cell sorting (FACS)-based single-cell and cell-type isolation with plant cells, which is suitable for downstream multi-omics analysis and other studies. Using Arabidopsis root fluorescent marker lines, we demonstrate how particular cell types, such as xylem-pole pericycle cells, lateral root initial cells, lateral root cap cells, cortex cells, and endodermal cells, are isolated. Furthermore, an effective downstream transcriptome analysis method using Smart-seq2 is also provided. The cell isolation method and transcriptome analysis techniques can be adapted to other cell types and plant species and have broad application potential in plant science.

The feasibility and effectiveness of high-throughput scRNA-seq methods herald a single-cell era in plant research. Presented here is a robust and complete procedure for isolating specific Arabidopsis thaliana root cell types and subsequent transcriptome library construction and analysis.

In multicellular organisms, developmental programming and environmental responses can be highly divergent in different cell types or even within cells, ...