Patch Clamp Setup:
Optics:&nbsp; The optics are very important to find a good cell, and to establish the position of it.&nbsp;&nbsp;
Try to get a clear image of the cells: sharp edges, soft-looking cell.
Scan the whole field to look for good MNTB principal cells with attached calyx.&nbsp;Rotate dish to look for calyces from different angles. At first, it is OK to practice on balloon-shaped terminal.
Pick cell at surface of slice, or in the 2nd cell layer. Target&nbsp;the first&nbsp;1/3rd of cell with pipette
Identifying Calyxes: Look for a double membrane (see Figure 1), and rotate the slice dish to see it from different angles to help confirm that it is a calyx.
<img src="/files/ftp_upload/old/244_2008_8_22_2/244_Figure-01.png" alt="Figure 1" width="298" height="159" /> Figure 1
&nbsp;
Depth of Calyx: Calyx should be on the surface or as close to the surface as possible.
Surface available for patching: Use fine-focus knob on microscope to determine how "wide/deep" the calyx is.&nbsp; For example, ~10% of a full turn on the fine focus will give you more than enough surface area to patch onto.
Sealing onto a presynaptic cell:&nbsp; To get to cell attached, look for a "small" deformation on the cell surface due to pos pressure (~0.15psi) in the pipette, use manipulator to run pipette up, down and across, and even into the surface of the presyn terminal to get a good deformation, then release pressure and apply suction, if and as necessary.
PULSE, data acquisition program:
Need to increase buffer size before&nbsp;first use, and whenever required by sampling capacity.
Need to load modified macros each time.
Liquid Junction Potential: Presyn Recording Solution is -11mV (negative 11mV).
Presyn: Cslow=~15 pF
Rs comp for presyn: 10 &mu;sec, 65 % (more compensation may possible w/out oscillations)&nbsp;&nbsp;
Before recording capacitance: Test current relaxation (10 mV, 10 msec jump) to see whether relaxation is monoexponential, i.e., whether presyn term can be modelled by a single compartment.
Filters: Set at 30 kHz and 10 kHz (Bessel filter 1 and 2 respectively) during relaxation measurement, to make sure&nbsp;a fast component isn't missed out on.
During mini recordings, Xinsheng used 10 kHz and 5kHz.&nbsp; LGW asked me to use only filter 1 set at 30 kHz to make sure we can measure rise-time of mini.
Files naming: 7 digits 000mmxx, where mm is month (or month and year) and xx is cell number.
Cleaning Solution Lines: Lines cleaned at end of experiment with 20 ml of 0.1 M HCl followed by 200 ml ddH2O.&nbsp;
External Solutions are recycled, pump speed is 20-30 rpm. &nbsp;
(solution returning from bath chamber flows back into the graduated cylinder).
Set up 3 outgoing lines to ensure sufficient suction.
Pipette Presynaptic Recording Solution: ~310 milli Osmolar 
Presyn Solution needs to be ~310 mOsm to prevent R-access increase during experiment.
Presyn pipette solution is different from postsyn pipette solution (Presyn has ATP &amp; GTP for ex.).
TTX-TEA Solution (to isolate Ca currents):
<ul>
<li>Try to apply after sealing, or even patching, onto the cell, as TEA in solution blocks K-channels and depolarizes the cell.&nbsp; This is not good for the cell.&nbsp;For the same reason, it might not be possible to reuse the slice after TTX is applied.</li>
<li>Compare&nbsp;the first and last response of the cell, or slice to check for any effect of prolonged depolarization. </li>
<li>TTX is used at 1 &mu;M instead of 0.5 &mu;M so the effect is faster. Need to wait less time after changing solutions.</li>
</ul>
Cutting Slices
Vibratome settings:
<ul>
<li>70Hz lateral vibrations</li>
<li>Amplitude: 1.0 mm</li>
<li>Forward speed 0.01-0.02 mm/sec while cutting slices with calyx, 0.1 otherwise thickness: 180 &mu;m (~150 &mu;m in older animals)</li>
</ul>
Slices incubate at 37&ordm;C for 1 hour (includes cutting time), i.e., leave in bath 15-20 minutes after cutting.
Pipettes:
Presyn: 3.5-4.5 M&Omega; at first, 3.0-3.5 M&Omega; when feel more confident
Use puller manual to set settings. Use delay feature because glass is thick (delays of 200 or 1 work)
Glass type: Borosilicate, standard wall, no filament
Outer Diameter: 2.0 mm
Inner Diameter 1.16 mm
Length: 7.5 cm

methods for patch clamp capacitance recordings from the calyx

We demonstrate the basic techniques for presynaptic patch clamp recording at the calyx of Held, a mammalian central nervous system nerve terminal. Electrical recordings from the presynaptic terminal allow the measurement of action potentials, calcium channel currents, vesicle fusion (exocytosis) and subsequent membrane uptake (endocytosis). The fusion of vesicles containing neurotransmitter causes the vesicle membrane to be added to the cell membrane of the calyx. This increase in the amount of cell membrane is measured as an increase in capacitance. The subsequent reduction in capacitance indicates endocytosis, the process of membrane uptake or removal from the calyx membrane. Endocytosis, is necessary to maintain the structure of the calyx and it is also necessary to form vesicles that will be filled with neurotransmitter for future exocytosis events. Capacitance recordings at the calyx of Held have made it possible to directly and rapidly measure vesicular release and subsequent endocytosis in a mammalian CNS nerve terminal. In addition, the corresponding postsynaptic activity can be simultaneously measured by using paired recordings. Thus a complete picture of the presynaptic and postsynaptic electrical activity at a central nervous system synapse is achievable using this preparation. Here, the methods for slice preparation, morphological features for identification of calyces of Held, basic patch clamping techniques, and examples of capacitance recordings to measure exocytosis and endocytosis are presented.

Watch this Scientific Journal Video about Methods for Patch Clamp Capacitance Recordings from the Calyx at JoVE.com

Methods for Patch Clamp Capacitance Recordings from the Calyx

We demonstrate the basic techniques for presynaptic patch clamp recording at the calyx of Held, a mammalian central nervous system nerve terminal.

We demonstrate the basic techniques for presynaptic patch clamp recording at the calyx of Held, a mammalian central nervous system nerve terminal. ...

methods-for-patch-clamp-capacitance-recordings-from-the-calyx

Research

JoVE Journal

Biology

12.6K ビュー.  National Institute of Health. 

ビデオ: Methods for Patch Clamp Capacitance Recordings from the Calyx

Whole Cell Recordings from Brain of Adult Drosophila

In this video, we demonstrate the procedure for isolating whole brains from adult Drosophila in preparation for recording from single neurons. We begin by describing the dissecting solution and capture of the adult females used in our studies. The procedure for removing the whole brain intact, including both optic lobes, is illustrated. Dissection of the overlying trachea is also shown.  The isolated brain is not only small but needs special care in handling at this stage to prevent damage to the neurons, many of which are close to the outer surface of the tissue. We show how a special holder we developed is used to stabilize the brain in the recording chamber. A standard electrophysiology set up is used for recording from single neurons or pairs of neurons. A fluorescent image, viewed through the recording microscope, from a GAL4 line driving GFP expression (GH146) illustrates how projection neurons (PNs) are identified in the live brain. A high power Nomarski image shows a view of a single neuron that is being targeted for whole cell recording. When the brain is successfully removed without damage, the majority of the neurons are spontaneously active, firing action potentials and/or exhibiting spontaneous synaptic input. This in situ preparation, in which whole cell recording of identified neurons in the whole brain can be combined with genetic and pharmacological manipulations, is a useful model for exploring cellular physiology and plasticity in the adult CNS.

This video demonstrates the procedure for isolating whole brains from adult Drosophila in preparation for recording from single neurons using standard whole cell technology. It includes images of GFP labeled cells and neurons viewed during recording.

In this video, we demonstrate the procedure for isolating whole brains from adult Drosophila in preparation for recording from single neurons. We begin by ...

Patch Clamp Recording of Ion Channels Expressed in  Xenopus Oocytes

Since its development by Sakmann and Neher 1, 2, the patch clamp has become established as an extremely useful technique for electrophysiological measurement of single or multiple ion channels in cells. This technique can be applied to ion channels in both their native environment and expressed in heterologous cells, such as oocytes harvested from the African clawed frog, Xenopus laevis. Here, we describe the well-established technique of patch clamp recording from Xenopus oocytes. This technique is used to measure the properties of expressed ion channels either in populations (macropatch) or individually (single-channel recording). We focus on techniques to maximize the quality of oocyte preparation and seal generation. With all factors optimized, this technique gives a probability of successful seal generation over 90 percent. The process may be optimized differently by every researcher based on the factors he or she finds most important, and we present the approach that have lead to the greatest success in our hands.

This is intended as an introduction to patch clamp recording from Xenopus laevis oocytes. It covers vitelline membrane removal, formation of a gigaohm seal (gigaseal), and the optional conversion of the patch to the outside-out topology.

Since its development by Sakmann and Neher 1, 2, the patch clamp has become established as an extremely useful technique for electrophysiological ...

Pressure-polishing Pipettes for Improved Patch-clamp Recording

Pressure-polishing is a method for shaping glass pipettes for patch-clamp recording. We first developed this method for fabricating pipettes suitable for recording from small (&lt;3 m) neuronal cell bodies. The basic principal is similar to glass-blowing and combines air pressure and heat to modify the shape of patch pipettes prepared by a conventional micropipette puller. It can be applied to so-called soft (soda lime) and hard (borosilicate) glasses. Generally speaking, pressure polishing can reduce pipette resistance by 25% without decreasing the diameter of the tip opening (Goodman and Lockery, 2000). It can be applied to virtually any type of glass and requires only the addition of a high-pressure valve and fitting to a microforge. This technique is essential for recording from ultrasmall cells (&lt;5 m) and can also improve single-channel recording by minimizing pipette resistance. The blunt shape is also useful for perforated-patch clamp recording since this tip shape results in a larger membrane bleb available for perforation.

This is a guide to modifying the shape of glass micropipettes. Specifically, by using heat and air pressure the taper is widened without increasing the tip opening, leading to lower pipette resistance. This is critical to obtain low noise recordings of small cells but is useful in many applications.

Pressure-polishing is a method for shaping glass pipettes for patch-clamp recording.  We first developed this method for fabricating pipettes suitable for ...

Electrophysiological Methods for Recording Synaptic Potentials from the NMJ of Drosophila Larvae

In this video, we describe the electrophysiological methods for recording synaptic transmission at the neuromuscular junction (NMJ) of Drosophila larva. The larval neuromuscular system is a model synapse for the study of synaptic physiology and neurotransmission, and is a valuable research tool that has defined genetics and is accessible to experimental manipulation. Larvae can be dissected to expose the body wall musculature, central nervous system, and peripheral nerves. The muscles of Drosophila and their innervation pattern are well characterized and muscles are easy to access for intracellular recording. Individual muscles can be identified by their location and orientation within the 8 abdominal segments, each with 30 muscles arranged in a pattern that is repeated in segments A2 - A7. Dissected drosophila larvae are thin and individual muscles and bundles of motor neuron axons can be visualized by transillumination1. Transgenic constructs can be used to label target cells for visual identification or for manipulating gene products in specific tissues. In larvae, excitatory junction potentials (EJP&#8217;s) are generated in response to vesicular release of glutamate from the motoneurons at the synapse. In dissected larvae, the EJP can be recorded in the muscle with an intracellular electrode. Action potentials can be artificially evoked in motor neurons that have been cut posterior to the ventral ganglion, drawn into a glass pipette by gentle suction and stimulated with an electrode. These motor neurons have distinct firing thresholds when stimulated, and when they fire simultaneously, they generate a response in the muscle. Signals transmitted across the NMJ synapse can be recorded in the muscles that the motor neurons innervate. The EJP&#8217;s and minature excitatory junction potentials (mEJP&#8217;s) are seen as changes in membrane potential. Electrophysiological responses are recorded at room temperature in modified minimal hemolymph-like solution2 (HL3) that contains 5 mM Mg2+ and 1.5 mM Ca2+. Changes in the amplitude of evoked EJP&#8217;s can indicate differences in synaptic function and structure. Digitized recordings are analyzed for EJP amplitude, mEJP frequency and amplitude, and quantal content.

Here we describe electrophysiological methods for measuring synaptic transmission at the neuromuscular junction of Drosophila larva. Evoked release is initiated artificially by stimulating the motor neuron axons, and transmission through the NMJ can be measured by the postsynaptic response evoked in the muscle.

In this video, we describe the electrophysiological methods for recording synaptic transmission at the neuromuscular junction (NMJ) of Drosophila larva. ...

Single-cell Suction Recordings from Mouse Cone Photoreceptors

Rod and cone photoreceptors in the retina are responsible for light detection. In darkness, cyclic nucleotide-gated (CNG) channels in the outer segment are open and allow cations to flow steadily inwards across the membrane, depolarizing the cell. Light exposure triggers the closure of the CNG channels, blocks the inward cation current flow, and thus results in cell hyperpolarization. Based on the polarity of photoreceptors, a suction recording method was developed in 1970s that, unlike the classic patch-clamp technique, does not require penetrating the plasma membrane 1. Drawing the outer segment into a tightly-fitting glass pipette filled with extracellular solution allows recording the current changes in individual cells upon test-flash exposure. However, this well-established "outer-segment-in (OS-in)" suction recording is not suitable for mouse cone recordings, because of the low percentage of cones in the mouse retina (3%) and the difficulties in identifying the cone outer segments. Recently, an inner-segment-in (IS-in) recording configuration was developed to draw the inner segment/nuclear region of the photoreceptor into the recording pipette 2,3. In this video, we will show how to record from individual mouse cone photoresponses using single-cell suction electrode.

We will show how to record flash responses from single mouse cones using a suction electrode.

Rod and cone photoreceptors in the retina are responsible for light detection. In darkness, cyclic nucleotide-gated (CNG) channels in the outer segment ...

Patch Clamp and Perfusion Techniques for Studying Ion Channels Expressed in Xenopus oocytes

The protocol presented here is designed to study the activation of the large conductance, voltage- and Ca2+-activated K+ (BK) channels. The protocol may also be used to study the structure-function relationship for other ion channels and neurotransmitter receptors1. BK channels are widely expressed in different tissues and have been implicated in many physiological functions, including regulation of smooth muscle contraction, frequency tuning of inner hair cells and regulation of neurotransmitter release2-6. BK channels are activated by membrane depolarization and by intracellular Ca2+ and Mg2+ 6-9. Therefore, the protocol is designed to control both the membrane voltage and the intracellular solution. In this protocol, messenger RNA of BK channels is injected into Xenopus laevis oocytes (stage V-VI) followed by 2-5 days of incubation at 18&deg;C10-13. Membrane patches that contain single or multiple BK channels are excised with the inside-out configuration using patch clamp techniques10-13. The intracellular side of the patch is perfused with desired solutions during recording so that the channel activation under different conditions can be examined. To summarize, the mRNA of BK channels is injected into Xenopus laevis oocytes to express channel proteins on the oocyte membrane; patch clamp techniques are used to record currents flowing through the channels under controlled voltage and intracellular solutions.

Patch Clamp and Perfusion Techniques for Studying Ion Channels Expressed in Xenopus oocytes

Ionic current of BK channels is recorded using patch clamp techniques. BK channels are expressed in Xenopus oocytes by injecting messenger RNA. The intracellular solution during patch clamp recordings is controlled by a perfusion system.

The protocol presented here is designed to study the activation of the large conductance, voltage- and Ca2+-activated K+ (BK) channels. The protocol may ...

Exploring Arterial Smooth Muscle Kv7 Potassium Channel Function using Patch Clamp Electrophysiology and Pressure Myography

Contraction or relaxation of smooth muscle cells within the walls of resistance arteries determines the artery diameter and thereby controls flow of blood through the vessel and contributes to systemic blood pressure. The contraction process is regulated primarily by cytosolic calcium concentration ([Ca2+]cyt), which is in turn controlled by a variety of ion transporters and channels. Ion channels are common intermediates in signal transduction pathways activated by vasoactive hormones to effect vasoconstriction or vasodilation. And ion channels are often targeted by therapeutic agents either intentionally (e.g. calcium channel blockers used to induce vasodilation and lower blood pressure) or unintentionally (e.g. to induce unwanted cardiovascular side effects).
Kv7 (KCNQ) voltage-activated potassium channels have recently been implicated as important physiological and therapeutic targets for regulation of smooth muscle contraction. To elucidate the specific roles of Kv7 channels in both physiological signal transduction and in the actions of therapeutic agents, we need to study how their activity is modulated at the cellular level as well as evaluate their contribution in the context of the intact artery.
The rat mesenteric arteries provide a useful model system. The arteries can be easily dissected, cleaned of connective tissue, and used to prepare isolated arterial myocytes for patch clamp electrophysiology, or cannulated and pressurized for measurements of vasoconstrictor/vasodilator responses under relatively physiological conditions. Here we describe the methods used for both types of measurements and provide some examples of how the experimental design can be integrated to provide a clearer understanding of the roles of these ion channels in the regulation of vascular tone.

Measurements of Kv7 (KCNQ) potassium channel activity in isolated arterial myocytes (using patch clamp electrophysiological techniques) in parallel with measurements of constrictor/dilator responses (using pressure myography) can reveal important information about the roles of Kv7 channels in vascular smooth muscle physiology and pharmacology.

Contraction  or relaxation of smooth muscle cells within the walls of resistance arteries  determines the artery diameter and thereby controls flow of ...

Giant Liposome Preparation for Imaging and Patch-Clamp Electrophysiology

The reconstitution of ion channels into chemically defined lipid membranes for electrophysiological recording has been a powerful technique to identify and explore the function of these important proteins. However, classical preparations, such as planar bilayers, limit the manipulations and experiments that can be performed on the reconstituted channel and its membrane environment. The more cell-like structure of giant liposomes permits traditional patch-clamp experiments without sacrificing control of the lipid environment.
Electroformation is an efficient mean to produce giant liposomes &gt;10 &mu;m in diameter which relies on the application of alternating voltage to a thin, ordered lipid film deposited on an electrode surface. However, since the classical protocol calls for the lipids to be deposited from organic solvents, it is not compatible with less robust membrane proteins like ion channels and must be modified. Recently, protocols have been developed to electroform giant liposomes from partially dehydrated small liposomes, which we have adapted to protein-containing liposomes in our laboratory.
We present here the background, equipment, techniques, and pitfalls of electroformation of giant liposomes from small liposome dispersions. We begin with the classic protocol, which should be mastered first before attempting the more challenging protocols that follow. We demonstrate the process of controlled partial dehydration of small liposomes using vapor equilibrium with saturated salt solutions. Finally, we demonstrate the process of electroformation itself. We will describe simple, inexpensive equipment that can be made in-house to produce high-quality liposomes, and describe visual inspection of the preparation at each stage to ensure the best results.

Reconstituting functional membrane proteins into giant liposomes of defined composition is a powerful approach when combined with patch-clamp electrophysiology. However, conventional giant liposome production may be incompatible with protein stability. We describe protocols for producing giant liposomes from pure lipids or small liposomes containing ion channels.

The reconstitution of ion channels into chemically defined lipid membranes for electrophysiological recording has been a powerful technique to identify ...

One-channel Cell-attached Patch-clamp Recording

Ion channel proteins are universal devices for fast communication across biological membranes. The temporal signature of the ionic flux they generate depends on properties intrinsic to each channel protein as well as the mechanism by which it is generated and controlled and represents an important area of current research. Information about the operational dynamics of ion channel proteins can be obtained by observing long stretches of current produced by a single molecule. Described here is a protocol for obtaining one-channel cell-attached patch-clamp current recordings for a ligand gated ion channel, the NMDA receptor, expressed heterologously in HEK293 cells or natively in cortical neurons. Also provided are instructions on how to adapt the method to other ion channels of interest by presenting the example of the mechano-sensitive channel PIEZO1. This method can provide data regarding the channel&#8217;s conductance properties and the temporal sequence of open-closed conformations that make up the channel&#8217;s activation mechanism, thus helping to understand their functions in health and disease.

Described here is a procedure for obtaining long stretches of current recording from one ion channel with the cell-attached patch-clamp technique. This method allows for observing, in real time, the pattern of open-close channel conformations that underlie the biological signal. These data inform about channel properties in undisturbed biological membranes.

Ion channel proteins are universal devices for fast communication across biological membranes. The temporal signature of the ionic flux they generate ...

Reconstitution of a Transmembrane Protein, the Voltage-gated Ion Channel, KvAP, into Giant Unilamellar Vesicles for Microscopy and Patch Clamp Studies

Giant Unilamellar Vesicles (GUVs) are a popular biomimetic system for studying membrane associated phenomena. However, commonly used protocols to grow GUVs must be modified in order to form GUVs containing functional transmembrane proteins. This article describes two dehydration-rehydration methods &#8212; electroformation and gel-assisted swelling &#8212; to form GUVs containing the voltage-gated potassium channel, KvAP. In both methods, a solution of protein-containing small unilamellar vesicles is partially dehydrated to form a stack of membranes, which is then allowed to swell in a rehydration buffer. For the electroformation method, the film is deposited on platinum electrodes so that an AC field can be applied during film rehydration. In contrast, the gel-assisted swelling method uses an agarose gel substrate to enhance film rehydration. Both methods can produce GUVs in low (e.g., 5 mM) and physiological (e.g., 100 mM) salt concentrations. The resulting GUVs are characterized via fluorescence microscopy, and the function of reconstituted channels measured using the inside-out patch-clamp configuration. While swelling in the presence of an alternating electric field (electroformation) gives a high yield of defect-free GUVs, the gel-assisted swelling method produces a more homogeneous protein distribution and requires no special equipment.

The reconstitution of the transmembrane protein, KvAP, into giant unilamellar vesicles (GUVs) is demonstrated for two dehydration-rehydration methods &#8212; electroformation, and gel-assisted swelling. In both methods, small unilamellar vesicles containing the protein are fused together to form GUVs that can then be studied by fluorescence microscopy and patch-clamp electrophysiology.

Giant Unilamellar Vesicles (GUVs) are a popular biomimetic system for studying membrane associated phenomena. However, commonly used protocols to grow ...