This work is supported by the National Cancer Institute at the National Institute of Health grant R01 CA140257-01.

NOTE: Informed consent was obtained from the patients. Also, this research has been performed in compliance with all institutional, national, and international guidelines for human welfare.
1. Prepare Computer
<ol>
	<li>Turn laptop on and connect USB from the DVI2USB Capture Card.</li>
</ol>
2. Prepare Monitor
<ol>
	<li>Connect DVI cable to monitor and PinP to allow the endoscopist to view videos from these screens rather than the computer.</li>
	<li>Make sure the standing monitor is on and is set to DVI.</li>
	<li>Connect PinP to the back of the Olympus system then press the input button on the Olympus system to view the image on the large monitor mounted on the wall.</li>
</ol>
3. Laser Diode Driver Setting
<ol>
	<li>Check to make sure the laser diode driver is OFF. It should only be turned on a couple minutes before imaging is performed.</li>
</ol>
4. Power Strip
<ol>
	<li>Plug in laptop, processor, laser diode driver, DVI splitter, and epiphan capture card into the power strip.</li>
</ol>
5. Run MDE Widefield on the Laptop Desktop
<ol>
	<li>Hit &#8216;Current Folder&#8217;.</li>
	<li>Type patient number and initials and press &#8216;Create Patient Folder&#8217;.</li>
</ol>
6. Prepare Cap and Filter
<ol>
	<li>When handling filter, always use gloves and Kimwipes to minimize the transfer of oil and debris to the filter. Gauze or alcohol swabs may leave fibers that can interfere with imaging.</li>
	<li>Place a few Kimwipes onto a table to create a platform to lay down the filter and cap. This disinfected area should be easily accessible to the gastroenterologist during the procedure.</li>
	<li>Lay down the filter and cap and keep Kimwipes close by for use during the procedure.</li>
</ol>
7. Patient Preparation
<ol>
	<li>Consent patient on use of VFI and proflavine dye before arriving to endo suite.&#160;</li>
	<li>Position patient for upper endoscopy procedure.</li>
	<li>Proceed with standard white-light imaging using a multispectral digital microscope (MDM)7.</li>
</ol>
8. Insert and Spray Proflavine
<ol>
	<li>After finishing with white-light imaging, insert and spray proflavine dye over tissue of interest. 1-5 mm should be sufficient depending on the area of the Barrett&#8217;s tissue. By spraying the proflavine dye at this step, ample time (at least 1 min) is given for sufficient tissue absorption before VFI. Proflavine, which is covered under an investigational new drug application from the FDA (IND 102,217), is a fluorescent contrast agent that concentrates within cell nuclei shortly after application. Although VFI cannot resolve individual cellular morphology, when the laser diode pans over tissue, the reflected light enables the endoscopist to appreciate overall glandular morphology.</li>
</ol>
9. Turn on Laser Diode
<ol>
	<li>Turn on the laser diode. Do this at least 2 min&#160;before imaging begins.</li>
</ol>
10. Prepare Endoscope for VFI
<ol>
	<li>Withdraw the endoscope completely.</li>
	<li>Prior to handling the endoscope, ensure that the assistant has two pairs of gloves on.</li>
	<li>Have the endoscopist hold the endoscope in front of the assistant who is next to the Kimwipe platform detailed above.</li>
	<li>With Kimwipes, have the assistant cleans the tip of the endoscope. Make sure to clean the front surface gently and also clean a few centimeters along the side of the endoscope for easier handling.</li>
	<li>After cleaning, have the assistant dispose of the outer pair of gloves.</li>
	<li>Have the assistant put on the filter. Insert the short cylindrical protuberance on the filter into its complementary hole in the endoscope. Keep the endoscope vertical to aid the process.</li>
	<li>Holding the filter in place, slide the cap over the filter and push it down over the tip of the endoscope. Make sure the cap is secure and pushed completely on with the edges flush with the endoscope. Make sure the lip of the cap slightly extends over the tip of the endoscope. Lastly, make sure the filter is still in place and flush with the tip of the endoscope.</li>
</ol>
11. Insert the Endoscope Back into the Esophagus and Image
12. Remove Endoscope from Esophagus
<ol>
	<li>Using Kimwipes carefully pull the cap and filter off the endoscope. Throw away the cap and clean the filter for the next case.&#160;</li>
</ol>
13. Clean Filter
<ol>
	<li>Gently clean the filter with Kimwipes.</li>
	<li>Fill a small cup with Cydex and submerge the filter for 12 min. Every few min&#160;turn the filter over.</li>
	<li>Gently clean the filter with Kimwipes.</li>
	<li>Submerge filter, this time in sterile water. After 5 min, use a squirt bottle and lightly spray sterile water over the filter.</li>
	<li>Place filter on a few Kimwipes and let it dry.</li>
	<li>Once dry, place in storage container in between Kimwipes.</li>
</ol>

<ol>
	<li>Modiano, N., Gerson, L. B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Barrett's+Esophagus:+Incidence,+etiology,+pathophysiology,+prevention+and+treatment.">Barrett's Esophagus: Incidence, etiology, pathophysiology, prevention and treatment.</a> Therapeutics and Clinical Risk Management. 3, 1035-1145 (2007).</li><li>Brown, L. M., Devesa, S. S., Chow, W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Incidence+of+Adenocarcinoma+of+the+esophagus+among+white+Americans+by+sex,+stage,+and+age.">Incidence of Adenocarcinoma of the esophagus among white Americans by sex, stage, and age.</a> Journal of the National Cancer Institute. 100, 1184-1187 (2008).</li><li>Siegel, R., Naishadham, D., Ahmedin, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Cancer+Statistics,+2012.">Cancer Statistics, 2012.</a> A Cancer Journal for Clinicians. 62, 10-29 (2012).</li><li>Vieth, M., Ell, C., Gossner, L., May, A., Stolte, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Histological+analysis+of+endoscopic+resection+specimens+from+326+patients+with+Barrett's+esophagus+and+early+neoplasia.">Histological analysis of endoscopic resection specimens from 326 patients with Barrett's esophagus and early neoplasia.</a> Endoscopy. 36, 776-781 (2004).</li><li>Pohl, H., Rosch, T., Vieth, M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Miniprobe+confocal+laser+microscopy+for+the+detection+of+invisible+neoplasia+in+patients+with+Barrett's+oesophagus.">Miniprobe confocal laser microscopy for the detection of invisible neoplasia in patients with Barrett's oesophagus.</a> Gut. 57, 1648-1653 (2008).</li><li>Thekkek, N., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Modular+video+endoscopy+for+in+vivo+cross-polarized+and+vital-dye+fluorescence+imaging+of+Barrett's-associated+neoplasia.">Modular video endoscopy for in vivo cross-polarized and vital-dye fluorescence imaging of Barrett's-associated neoplasia.</a> Journal of Biomedical Optics. 18, 026007 (2013).</li><li>Roblyer, D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Multispectral+optical+imaging+device+for+in+vivo+detection+of+oral+neoplasia.">Multispectral optical imaging device for in vivo detection of oral neoplasia.</a> Journal of Biomedical Optics. 13, 024019 (2008).</li><li>Egger, K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Biopsy+surveillance+is+still+necessary+in+patients+with+Barrett's+oesophagus+despite+new+endoscopic+imaging+techniques.">Biopsy surveillance is still necessary in patients with Barrett's oesophagus despite new endoscopic imaging techniques.</a> Gut. 52, 18-23 (2003).</li><li>Thekkek, N., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Vital-dye+enhanced+fluorescence+imaging+of+GI+mucosa:+metaplasia,+neoplasia,+inflammation.">Vital-dye enhanced fluorescence imaging of GI mucosa: metaplasia, neoplasia, inflammation.</a> Gastrointestinal Endoscopy. 75, 877-887 (2012).</li><li>Muldoon, T. J., Anandasabapathy, S., Maru, D., Richards-Kortum, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=High-resolution+imaging+in+Barrett's+esophagus:+a+novel,+low-cost+endoscopic+microscope.">High-resolution imaging in Barrett's esophagus: a novel, low-cost endoscopic microscope.</a> Gastrointestinal Endoscopy. 68, 737-744 (2008).</li></ol>

There is nothing to disclose.

With standard endoscopic surveillance, neoplasia in BE is often missed8 because benign metaplasia can be indistinguishable from high-grade dysplasia and adenocarcinoma. As a tool that would better enable gastroenterologists to remedy this currently unavoidable error, vital-dye enhanced fluorescence imaging highlights a tissue&#8217;s glandular morphology thereby providing a distinct feature to differentiate the tissue types. Moreover, by providing a field of view up to 2.5 cm, VFI enables endoscopists to pan o...

Over the last forty years, the incidence of esophageal adenocarcinoma (EAC) has increased significantly1,2; yet due to late diagnosis, the five-year&#160;survival rate is less than 20%3. The current standard of endoscopic surveillance in BE, the precursor to EAC, is white light endoscopy with random four-quandrant forceps&#8217; biopsies of the segment. Unfortunately, this technique often misses neoplasia, which can be flat, subtle and difficult to differentiate on standard white light imaging4. While there has been success in using confocal laser microscopy to highlight cellular features in vivo, lesions can still be missed due to the decreased field of view5. Having a &#8216;bridge&#8217; technology that can highlight areas for further confocal microendoscopic imaging would be markedly valuable.
Consequently, an enhanced red-flag imaging modality that improves the ability to target and biopsy early neoplasia in BE would be instrumental in detecting EAC at an early, curable stage and could lead to more effective treatment and subsequently improved survival rates. VFI is a novel technique that combines high-resolution epithelial imaging with exogenous topical fluorescent contrast, proflavine, to highlight glandular morphology and delineate neoplasia (high grade dysplasia and cancer) in the distal esophagus in hopes of improving the in vivo diagnosis6. Upon excitation of the proflavine, which concentrates within cell nuclei shortly after application, the fluorescent images provide spatial resolution of 50 to 100 &#956;m&#160;and a field of view up to 2.5 cm,&#160;allowing endoscopists to visualize glandular morphology. As a result, this approach enables gastroenterologists to distinguish classic Barrett&#8217;s metaplasia, which has continuous, evenly-spaced glands and an overall homogenous morphology, from BE with neoplasia, which has obliteration of the glandular architecture. Here we describe the protocol of this new technique with a multispectral endoscope, and provide representative results to demonstrate the utility of this device in depicting the morphological transformation from benign metaplasia to high-grade dysplasia and cancer.

<table border="0" cellpadding="0" cellspacing="0" width="650">
	<tbody>
		<tr>
			<td>Filter*</td>
			<td>Schott North America, Inc., Duryea, Pennsylvania</td>
			<td>Not Applicable</td>
			<td>495-nm long-pass filter</td>
		</tr>
		<tr>
			<td>Halo Cap &#8211; Medium*</td>
			<td>Barrx Medical</td>
			<td>CP-002A</td>
			<td></td>
		</tr>
		<tr>
			<td>Processor*</td>
			<td>Pentax</td>
			<td>EPK-i</td>
			<td></td>
		</tr>
		<tr>
			<td>Multispectral Digital Microscope**</td>
			<td>Not Applicable</td>
			<td>Not Applicable</td>
			<td></td>
		</tr>
		<tr>
			<td>Kimwipes</td>
			<td>Kimberly-Clark</td>
			<td>KimTech Science</td>
			<td>S-8115</td>
		</tr>
		<tr>
			<td>Cidex</td>
			<td>Advanced Sterilization Products&#160;</td>
			<td>CIDEX OPA Solution</td>
			<td></td>
		</tr>
		<tr>
			<td>Proflavine hemisulfate (0.01% w/v)</td>
			<td></td>
			<td></td>
			<td>FDA (IND 102,217)</td>
		</tr>
		<tr>
			<td>Laser Diode*</td>
			<td>Nichia Corporation</td>
			<td>Not Applicable</td>
			<td>455-nm</td>
		</tr>
		<tr>
			<td>Image Capture*</td>
			<td>Labview</td>
			<td>Not Applicable</td>
			<td></td>
		</tr>
		<tr>
			<td>Spray Catheter</td>
			<td>Olympus</td>
			<td>Not Applicable</td>
			<td></td>
		</tr>
		<tr>
			<td></td>
			<td></td>
			<td></td>
			<td>*Equipment specifics within Reference 6. **Equipment specifics within Reference 7</td>
		</tr>
	</tbody>
</table>

diagnosis of neoplasia in barrett&#8217;s esophagus using vital-dye enhanced fluorescence imaging

The ability to differentiate benign metaplasia in Barrett&#8217;s Esophagus (BE) from neoplasia in vivo remains difficult as both tissue types can be flat and indistinguishable with white light imaging alone. As a result, a modality that highlights glandular architecture would be useful to discriminate neoplasia from benign epithelium in the distal esophagus. VFI is a novel technique that uses an exogenous topical fluorescent contrast agent to delineate high grade dysplasia and cancer from benign epithelium. Specifically, the fluorescent images provide spatial resolution of 50 to 100 &#956;m&#160;and a field of view up to 2.5 cm,&#160;allowing endoscopists to visualize glandular morphology. Upon excitation, classic Barrett&#8217;s metaplasia appears as continuous, evenly-spaced glands and an overall homogenous morphology; in contrast, neoplastic tissue appears crowded with complete obliteration of the glandular framework. Here we provide an overview of the instrumentation and enumerate the protocol of this new technique. While VFI affords a gastroenterologist with the glandular architecture of suspicious tissue, cellular dysplasia cannot be resolved with this modality. As such, one cannot morphologically distinguish Barrett&#8217;s metaplasia from BE with Low-Grade Dysplasia via this imaging modality. By trading off a decrease in resolution with a greater field of view, this imaging system can be used at the very least as a red-flag imaging device to target and biopsy suspicious lesions; yet, if the accuracy measures are promising, VFI may become the standard imaging technique for the diagnosis of neoplasia (defined as either high grade dysplasia or cancer) in the distal esophagus.

Figure 1B depicts classic Barrett's Esophagus with no dysplasia surrounded on the borders by normal squamous epithelium. Beginning with the flatter squamous tissue, which is peripherally located and indicated by the blue arrows, a homogenous area of dull fluorescence is present with no glandular architecture. The green arrows indicate a circular green line surrounding the squamous tissue. This outline is artifact resulting from the cap of the endoscope. Moving to the centrally located Barrett's tissue, g...

Watch this Scientific Journal Video about Diagnosis of Neoplasia in Barrettâ€™s Esophagus using Vital-dye Enhanced Fluorescence Imaging at JoVE.com

Diagnosis of Neoplasia in Barrett&amp;#8217;s Esophagus using Vital-dye Enhanced Fluorescence Imaging

Vital-dye enhanced fluorescence imaging (VFI) is a novel in vivo technique that combines high-resolution epithelial imaging with exogenous topical fluorescent contrast to highlight glandular morphology and delineate neoplasia (high grade dysplasia and cancer) in the distal esophagus.

Diagnosis of Neoplasia in Barrett&#8217;s Esophagus using Vital-dye Enhanced Fluorescence Imaging

The ability to differentiate benign metaplasia in Barrett&#8217;s Esophagus (BE) from neoplasia in vivo remains difficult as both tissue types can be flat ...

diagnosis-neoplasia-barretts-esophagus-using-vital-dye-enhanced

Research

JoVE Journal

Bioengineering

12.0K ビュー.  Icahn School of Medicine at Mount Sinai. バイタル色素増強蛍光イメージング（VFI）は腺の形態を強調表示し、食道に腫瘍（高度異形成および癌）線引きする外因性の局所蛍光造影で高解像度の上皮イメージングを組み合わせたin vivoでの技術では新規である。 

ビデオ: Diagnosis of Neoplasia in Barrett&#8217;s Esophagus using Vital-dye Enhanced Fluorescence Imaging

Three-dimensional Optical-resolution Photoacoustic Microscopy

Optical microscopy, providing valuable insights at the cellular and organelle levels, has been widely recognized as an enabling biomedical technology. As the mainstays of in vivo three-dimensional (3-D) optical microscopy, single-/multi-photon fluorescence microscopy and optical coherence tomography (OCT) have demonstrated their extraordinary sensitivities to fluorescence and optical scattering contrasts, respectively. However, the optical absorption contrast of biological tissues, which encodes essential physiological/pathological information, has not yet been assessable. 
The emergence of biomedical photoacoustics has led to a new branch of optical microscopy optical-resolution photoacoustic microscopy (OR-PAM)1, where the optical irradiation is focused to the diffraction limit to achieve cellular1 or even subcellular2 level lateral resolution. As a valuable complement to existing optical microscopy technologies, OR-PAM brings in at least two novelties. First and most importantly, OR-PAM detects optical absorption contrasts with extraordinary sensitivity (i.e., 100%). Combining OR-PAM with fluorescence microscopy3 or with optical-scattering-based OCT4 (or with both) provides comprehensive optical properties of biological tissues. Second, OR-PAM encodes optical absorption into acoustic waves, in contrast to the pure optical processes in fluorescence microscopy and OCT, and provides background-free detection. The acoustic detection in OR-PAM mitigates the impacts of optical scattering on signal degradation and naturally eliminates possible interferences (i.e., crosstalks) between excitation and detection, which is a common problem in fluorescence microscopy due to the overlap between the excitation and fluorescence spectra. 
Unique for optical absorption imaging, OR-PAM has demonstrated broad biomedical applications since its invention, including, but not limited to, neurology5, 6, ophthalmology7, 8, vascular biology9, and dermatology10. In this video, we teach the system configuration and alignment of OR-PAM as well as the experimental procedures for in vivo functional microvascular imaging.

Optical-resolution photoacoustic microscopy (OR-PAM) is an emerging technology capable of imaging optical absorption contrasts in vivo with cellular resolution and sensitivity. Here, we provide a visualized instruction on the experimental protocols of OR-PAM, including system configuration, system alignment, typical in vivo experimental procedures, and functional imaging schemes.

Optical microscopy, providing valuable insights at the cellular and organelle levels, has been widely recognized as an enabling biomedical technology. As ...

Fluorescence Lifetime Imaging of Molecular Rotors in Living Cells

Diffusion is often an important rate-determining step in chemical reactions or biological processes and plays a role in a wide range of intracellular events. Viscosity is one of the key parameters affecting the diffusion of molecules and proteins, and changes in viscosity have been linked to disease and malfunction at the cellular level.1-3 While methods to measure the bulk viscosity are well developed, imaging microviscosity remains a challenge. Viscosity maps of microscopic objects, such as single cells, have until recently been hard to obtain. Mapping viscosity with fluorescence techniques is advantageous because, similar to other optical techniques, it is minimally invasive, non-destructive and can be applied to living cells and tissues.
Fluorescent molecular rotors exhibit fluorescence lifetimes and quantum yields which are a function of the viscosity of their microenvironment.4,5 Intramolecular twisting or rotation leads to non-radiative decay from the excited state back to the ground state. A viscous environment slows this rotation or twisting, restricting access to this non-radiative decay pathway. This leads to an increase in the fluorescence quantum yield and the fluorescence lifetime. Fluorescence Lifetime Imaging (FLIM) of modified hydrophobic BODIPY dyes that act as fluorescent molecular rotors show that the fluorescence lifetime of these probes is a function of the microviscosity of their environment.6-8 A logarithmic plot of the fluorescence lifetime versus the solvent viscosity yields a straight line that obeys the F&ouml;rster Hoffman equation.9 This plot also serves as a calibration graph to convert fluorescence lifetime into viscosity.
Following incubation of living cells with the modified BODIPY fluorescent molecular rotor, a punctate dye distribution is observed in the fluorescence images. The viscosity value obtained in the puncta in live cells is around 100 times higher than that of water and of cellular cytoplasm.6,7 Time-resolved fluorescence anisotropy measurements yield rotational correlation times in agreement with these large microviscosity values. Mapping the fluorescence lifetime is independent of the fluorescence intensity, and thus allows the separation of probe concentration and viscosity effects. 
In summary, we have developed a practical and versatile approach to map the microviscosity in cells based on FLIM of fluorescent molecular rotors.

Fluorescence Lifetime Imaging (FLIM) has emerged as a key technique to image the environment and interaction of specific proteins and dyes in living cells. FLIM of fluorescent molecular rotors allows mapping of viscosity in living cells.

Diffusion is often an important rate-determining step in chemical reactions or biological processes and plays a role in a wide range of intracellular ...

Time-lapse Fluorescence Imaging of Arabidopsis Root Growth with Rapid Manipulation of The Root Environment Using The RootChip

The root functions as the physical anchor of the plant and is the organ responsible for uptake of water and mineral nutrients such as nitrogen, phosphorus, sulfate and trace elements that plants acquire from the soil. If we want to develop sustainable approaches to producing high crop yield, we need to better understand how the root develops, takes up a wide spectrum of nutrients, and interacts with symbiotic and pathogenic organisms. To accomplish these goals, we need to be able to explore roots in microscopic detail over time periods ranging from minutes to days.
We developed the RootChip, a polydimethylsiloxane (PDMS)- based microfluidic device, which allows us to grow and image roots from Arabidopsis seedlings while avoiding any physical stress to roots during preparation for imaging1 (Figure 1). The device contains a bifurcated channel structure featuring micromechanical valves to guide the fluid flow from solution inlets to each of the eight observation chambers2. This perfusion system allows the root microenvironment to be controlled and modified with precision and speed. The volume of the chambers is approximately 400 nl, thus requiring only minimal amounts of test solution.
Here we provide a detailed protocol for studying root biology on the RootChip using imaging-based approaches with real time resolution. Roots can be analyzed over several days using time lapse microscopy. Roots can be perfused with nutrient solutions or inhibitors, and up to eight seedlings can be analyzed in parallel. This system has the potential for a wide range of applications, including analysis of root growth in the presence or absence of chemicals, fluorescence-based analysis of gene expression, and the analysis of biosensors, e.g. FRET nanosensors3.

This article provides a protocol for cultivation of Arabidopsis seedlings in the RootChip, a microfluidic imaging platform that combines automated control of growth conditions with microscopic root monitoring and FRET-based measurement of intracellular metabolite levels.

The root functions as the physical anchor of the plant and is the organ responsible for uptake of water and mineral nutrients such as nitrogen, ...

High-resolution Spatiotemporal Analysis of Receptor Dynamics by Single-molecule Fluorescence Microscopy

Single-molecule microscopy is emerging as a powerful approach to analyze the behavior of signaling molecules, in particular concerning those aspect (e.g., kinetics, coexistence of different states and populations, transient interactions), which are typically hidden in ensemble measurements, such as those obtained with standard biochemical or microscopy methods. Thus, dynamic events, such as receptor-receptor interactions, can be followed in real time in a living cell with high spatiotemporal resolution. This protocol describes a method based on labeling with small and bright organic fluorophores and total internal reflection fluorescence (TIRF) microscopy to directly visualize single receptors on the surface of living cells. This approach allows one to precisely localize receptors, measure the size of receptor complexes, and capture dynamic events such as transient receptor-receptor interactions. The protocol provides a detailed description of how to perform a single-molecule experiment, including sample preparation, image acquisition and image analysis. As an example, the application of this method to analyze two G-protein-coupled receptors, i.e., &#946;2-adrenergic and &#947;-aminobutyric acid type B (GABAB) receptor, is reported. The protocol can be adapted to other membrane proteins and different cell models, transfection methods and labeling strategies.

This protocol describes how to use total internal reflection fluorescence microscopy to visualize and track single receptors on the surface of living cells and thereby analyze receptor lateral mobility, size of receptor complexes as well as to visualize transient receptor-receptor interactions. This protocol can be extended to other membrane proteins.

Single-molecule microscopy is emerging as a powerful approach to analyze the behavior of signaling molecules, in particular concerning those aspect (e.g., ...

3D Orbital Tracking in a Modified Two-photon Microscope: An Application to the Tracking of Intracellular Vesicles

The objective of this video protocol is to discuss how to perform and analyze a three-dimensional fluorescent orbital particle tracking experiment using a modified two-photon microscope1. As opposed to conventional approaches (raster scan or wide field based on a stack of frames), the 3D orbital tracking allows to localize and follow with a high spatial (10 nm accuracy) and temporal resolution (50 Hz frequency response) the 3D displacement of a moving fluorescent particle on length-scales of hundreds of microns2. The method is based on a feedback algorithm that controls the hardware of a two-photon laser scanning microscope in order to perform a circular orbit around the object to be tracked: the feedback mechanism will maintain the fluorescent object in the center by controlling the displacement of the scanning beam3-5. To demonstrate the advantages of this technique, we followed a fast moving organelle, the lysosome, within a living cell6,7. Cells were plated according to standard protocols, and stained using a commercially lysosome dye. We discuss briefly the hardware configuration and in more detail the control software, to perform a 3D orbital tracking experiment inside living cells. We discuss in detail the parameters required in order to control the scanning microscope and enable the motion of the beam in a closed orbit around the particle. We conclude by demonstrating how this method can be effectively used to track the fast motion of a labeled lysosome along microtubules in 3D within a live cell. Lysosomes can move with speeds in the range of 0.4-0.5 &#181;m/sec, typically displaying a directed motion along the microtubule network8.

In this video protocol we track - at high speed and in three dimensions - fluorescently labeled lysosomes within living cells, using the orbital tracking method in a modified two-photon microscope.

The objective of this video protocol is to discuss how to perform and analyze a three-dimensional fluorescent orbital particle tracking experiment using a ...

From Fast Fluorescence Imaging to Molecular Diffusion Law on Live Cell Membranes in a Commercial Microscope

It has become increasingly evident that the spatial distribution and the motion of membrane components like lipids and proteins are key factors in the regulation of many cellular functions. However, due to the fast dynamics and the tiny structures involved, a very high spatio-temporal resolution is required to catch the real behavior of molecules. Here we present the experimental protocol for studying the dynamics of fluorescently-labeled plasma-membrane proteins and lipids in live cells with high spatiotemporal resolution. Notably, this approach doesn&#8217;t need to track each molecule, but it calculates population behavior using all molecules in a given region of the membrane. The starting point is a fast imaging of a given region on the membrane. Afterwards, a complete spatio-temporal autocorrelation function is calculated correlating acquired images at increasing time delays, for example each 2, 3, n repetitions. It is possible to demonstrate that the width of the peak of the spatial autocorrelation function increases at increasing time delay as a function of particle movement due to diffusion. Therefore, fitting of the series of autocorrelation functions enables to extract the actual protein mean square displacement from imaging (iMSD), here presented in the form of apparent diffusivity vs average displacement. This yields a quantitative view of the average dynamics of single molecules with nanometer accuracy. By using a GFP-tagged variant of the Transferrin Receptor (TfR) and an ATTO488 labeled 1-palmitoyl-2-hydroxy-sn-glycero-3-phosphoethanolamine (PPE) it is possible to observe the spatiotemporal regulation of protein and lipid diffusion on &#181;m-sized membrane regions in the micro-to-milli-second time range.

Spatial distribution and temporal dynamics of plasma membrane proteins and lipids is a hot topic in biology. Here this issue is addressed by a spatio-temporal image fluctuation analysis that provides conceptually the same physical quantities of single particle tracking, but it uses small molecular labels and standard microscopy setups.

It has become increasingly evident that the spatial distribution and the motion of membrane components like lipids and proteins are key factors in the ...

Electrotaxis Studies of Lung Cancer Cells using a Multichannel Dual-electric-field Microfluidic Chip

The behavior of directional cell migration under a direct current electric-field (dcEF) is referred to as electrotaxis. The significant role of physiological dcEF in guiding cell movement during embryo development, cell differentiation, and wound healing has been demonstrated in many studies. By applying microfluidic chips to an electrotaxis assay, the investigation process is shortened and experimental errors are minimized. In recent years, microfluidic devices made of polymeric substances (e.g., polymethylmethacrylate, PMMA, or acrylic) or polydimethylsiloxane (PDMS) have been widely used in studying the responses of cells to electrical stimulation. However, unlike the numerous steps required to fabricate a PDMS device, the simple and rapid construction of the acrylic micro&#64258;uidic chip makes it suitable for both device prototyping and production. Yet none of the reported devices facilitate the efficient study of the simultaneous chemical and dcEF effects on cells. In this report, we describe our design and fabrication of an acrylic-based multichannel dual-electric-field (MDF) chip to investigate the concurrent effect of chemical and electrical stimulation on lung cancer cells. The MDF chip provides eight combinations of electrical/chemical stimulations in a single test. The chip not only greatly shortens the required experimental time but also increases accuracy in electrotaxis studies.

Many microfluidic devices have been developed for use in the study of electrotaxis. Yet, none of these chips allows the efficient study of the simultaneous chemical and electric-field (EF) effects on cells. We developed a polymethylmethacrylate-based device that offers better-controlled coexisting EF and chemical stimulation for use in electrotaxis research.

The behavior of directional cell migration under a direct current electric-field (dcEF) is referred to as electrotaxis. The significant role of ...

Conducting Multiple Imaging Modes with One Fluorescence Microscope

Fluorescence microscopy is a powerful tool to detect biological molecules in situ and monitor their dynamics and interactions in real-time. In addition to conventional epi-fluorescence microscopy, various imaging techniques have been developed to achieve specific experimental goals. Some of the widely used techniques include single-molecule fluorescence resonance energy transfer (smFRET), which can report conformational changes and molecular interactions with angstrom resolution, and single-molecule detection-based super-resolution (SR) imaging, which can enhance the spatial resolution approximately ten&#160;to twentyfold compared to diffraction-limited microscopy. Here we present a customer-designed integrated system, which merges multiple imaging methods in one microscope, including conventional epi-fluorescent imaging, single-molecule detection-based SR imaging, and multi-color single-molecule detection, including smFRET imaging. Different imaging methods can be achieved easily and reproducibly by switching optical elements. This set-up is easy to adopt by any research laboratory in biological sciences with a need for routine and diverse imaging experiments at a reduced cost and space relative to building separate microscopes for individual purposes.

Here we present a practical guide of building an integrated microscopy system, which merges conventional epi-fluorescent imaging, single-molecule detection-based super-resolution imaging, and multi-color single-molecule detection, including single-molecule fluorescence resonance energy transfer imaging, into one set-up in a cost-efficient way.

Fluorescence microscopy is a powerful tool to detect biological molecules in situ and monitor their dynamics and interactions in real-time. In addition to ...

Visualizing Adhesion Formation in Cells by Means of Advanced Spinning Disk-Total Internal Reflection Fluorescence Microscopy

In living cells, processes such as adhesion formation involve extensive structural changes in the plasma membrane and the cell interior. In order to visualize these highly dynamic events, two complementary light microscopy techniques that allow fast imaging of live samples were combined: spinning disk microscopy (SD) for fast and high-resolution volume recording and total internal reflection fluorescence (TIRF) microscopy for precise localization and visualization of the plasma membrane. A comprehensive and complete imaging protocol will be shown for guiding through sample preparation, microscope calibration, image formation and acquisition, resulting in multi-color SD-TIRF live imaging series with high spatio-temporal resolution. All necessary image post-processing steps to generate multi-dimensional live imaging datasets, i.e. registration and combination of the individual channels, are provided in a self-written macro for the open source software ImageJ. The imaging of fluorescent proteins during initiation and maturation of adhesion complexes, as well as the formation of the actin cytoskeletal network, was used as a proof of principle for this novel approach. The combination of high resolution 3D microscopy and TIRF provided a detailed description of these complex processes within the cellular environment and, at the same time, precise localization of the membrane-associated molecules detected with a high signal-to-background ratio.

An advanced microscope that permit fast and high-resolution imaging of both, the isolated plasma membrane and the surrounding intracellular volume, will be presented. The integration of spinning disk and total internal reflection fluorescence microscopy in one setup allows live imaging experiments at high acquisition rates up to 3.5 s per image stack.

In living cells, processes such as adhesion formation involve extensive structural changes in the plasma membrane and the cell interior. In order to ...

Using Nanoplasmon-Enhanced Scattering and Low-Magnification Microscope Imaging to Quantify Tumor-Derived Exosomes

Infected or malignant cells frequently secrete more exosomes, leading to elevated levels of disease-associated exosomes in the circulation. These exosomes have the potential to serve as biomarkers for disease diagnosis and to monitor disease progression and treatment response. However, most exosome analysis procedures require exosome isolation and purification steps, which are usually time-consuming and labor-intensive, and thus of limited utility in clinical settings. This report describes a rapid procedure to analyze specific biomarkers on the outer membrane of exosomes without requiring separate isolation and purification steps. In this method, exosomes are captured on the surface of a slide by exosome-specific antibodies and then hybridized with nanoparticle-conjugated antibody probes specific to a disease. After hybridization, the abundance of the target exosome population is determined by analyzing low-magnification dark-field microscope (LMDFM) images of the bound nanoparticles. This approach can be easily adopted for research and clinical use to analyze membrane-associated exosome biomarkers linked to disease.

Clinical translation of exosome-derived biomarkers for diseased and malignant cells is hindered by the lack of rapid and accurate quantification methods. This report describes the use of low-magnification dark-field microscope images to quantify specific exosome subtypes in small volume serum or plasma samples.

Infected or malignant cells frequently secrete more exosomes, leading to elevated levels of disease-associated exosomes in the circulation. These exosomes ...