1. Preparation of solutions and materials
These steps should be carried out several days in advance.
<ol>
	<li>Glass coverslips. Coverslips were cleaned by immersion for 10 minutes into a solution of Linbro 7X detergent : water, mixed at a 1 : 3 ratio and heated, with stirring, until clear. Coverslips were rinsed extensively with deionized water, and then baked at 450&#176;C for 6 hours. Loading coverslips into ceramic staining racks (see Reagents) simplified this process.</li>
	<li>Protein solution for stamping. Reconstitute fibronectin following the manufacturers instructions to a stock solution of 1 mg/ml concentration.</li>
</ol>
2. Cast stamps from the topological master
These steps can be carried out several days in advance. Store stamps pattern-up in a covered dish, such as a tissue culture dish.
<ol>
	<li>Remove loose dust from master using a stream of compressed, filtered air or inert gas.</li>
	<li>Place the master, patterned side up, in the bottom of a plastic dish just larger than the master. 60- or 100-mm tissue culture dishes are well suited for this purpose.</li>
	<li>In a polystyrene 50 ml centrifuge tube, combine the Sylgard components at a ratio of curing agent : elastomer base of 1 : 10 by weight. Mix thoroughly using a plastic device, such as a disposable pipette. Prepare at least 0.2 ml of elastomer per square centimeter of dish area.</li>
	<li>Centrifuge the 50 ml tube at 300 G for 5 min to remove air bubbles.</li>
	<li>Pour the elastomer over the master, then place in a desiccator, under vacuum, for 30 minutes.</li>
	<li>Cure the elastomer in an oven at 65&#176;C for at least 2 hours. Curing at higher temperatures and for longer times results in stiffer elastomer. Let cool to room temperature.</li>
	<li>Separate the sheet of stamps from the master.</li>
</ol>
3. Microcontact printing of fibronectin onto glass
<ol>
	<li>Cut out a single stamp. Stamps measuring 4 mm X 4 mm to 1 cm X 1 cm in area and 1 &#8211; 2 mm thick are easiest to start with. Place pattern side up on a glass slide or small plastic dish.</li>
	<li>Place stamp in a plasma cleaner, and process, under vacuum, for 30 seconds. A Harrick Scientific plasma cleaner (see Equipment), set at its highest output setting will render the PDMS surface hydrophilic. Longer times result in cracking of the elastomer.</li>
	<li>Dilute the fibronectin solution with deionized water to a stamping concentration of 50 &#181;g/ml.</li>
	<li>Place a small drop (10 &#8211; 50 &#181;l) of stamping solution on the stamp. It will spread across the hydrophilic surface. Add only enough solution that the drop covers the stamp, but does not run over the edges. Let protein adsorb to stamp for 5 minutes.</li>
	<li>Using a Kimwipe&#174; or other clean paper tissue, wick off most of the protein solution from the stamp, without touching the patterned region.</li>
	<li>Dry the remaining solution from the stamp under a stream of clean, dry, inert gas, such as nitrogen.</li>
	<li>Using tweezers, remove the stamp from the glass slide, invert, and place in contact with the cleaned glass coverslip (the surface to be patterned). Place a weight on top to promote good contact. The specific weight that provides the best patterning is dependent on the stamp size and pattern; start with a 5 g weight, and adjust between stampings. Leave stamp in contact with surface for 1 minutes.</li>
	<li>Carefully disassemble the stack, and separate stamp from coverslip.</li>
	<li>Vigorously rinse the patterned coverslip in PBS, followed by deionized water, to remove protein that is not adsorbed to the surface. Dry coverslip under a nitrogen stream.</li>
</ol>
&#160;Representative Results
Microcontact printing is a powerful process for patterning molecules on surfaces. This process has the ability to create features with dimensions ranging from tens of micrometers to hundreds of nanometers; in Fig. 1A, the logos on the left are each 200 &#181;m in height, while the green spots illustrated in Fig. 1B are 1 &#181;m in diameter and spaced at 4 &#181;m intervals, measured center-to-center. Fig. 1B also illustrates a powerful property of microcontact printing, namely that it is and additive process. Multiple rounds of microcontact printing can be applied to a single surface to create multicomponent systems3.
<img alt="Figure A" src="/files/ftp_upload/old/1065_2008_11_24_3/figure_a.jpg" /> <img alt="Figure B" src="/files/ftp_upload/old/1065_2008_11_24_4/FIGURE_B.jpg" />

<ol>
	<li>Chen, C. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Geometric+control+of+cell+life+and+death.">Geometric control of cell life and death.</a> Science. 276, 1425-1425 (1997).</li><li>Kumar, A., Whitesides, G. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Features+of+Gold+Having+Micrometer+to+Centimeter+Dimensions+can+be+Formed+Through+a+Combination+of+Stamping+with+an+Elastomeric+Stamp+and+an+Alkanethiol+"Ink"+Followed+by+Chemical+Etching.">Features of Gold Having Micrometer to Centimeter Dimensions can be Formed Through a Combination of Stamping with an Elastomeric Stamp and an Alkanethiol "Ink" Followed by Chemical Etching.</a> Applied Physics Letters. 63, 4-4 (1993).</li><li>St. John, P. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Preferential+Glial+Cell+Attachment+to+Microcontact-printed+Surfaces.">Preferential Glial Cell Attachment to Microcontact-printed Surfaces.</a> Journal of Neuroscience Methods. 75, 171-171 (1997).</li><li>Kam, L., Boxer, S. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Cell+adhesion+to+protein-micropatterned-supported+lipid+bilayer+membranes.">Cell adhesion to protein-micropatterned-supported lipid bilayer membranes.</a> Journal of Biomedical Materials Research. 55, 487-487 (2001).</li><li>Kung, L. A., Kam, L., Hovis, J. S., Boxer, S. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Patterning+Hybrid+Surfaces+of+Proteins+and+Supported+Lipid+Bilayers.">Patterning Hybrid Surfaces of Proteins and Supported Lipid Bilayers.</a> Langmuir. 16, 6773-6773 (2000).</li><li>Shen, K., Thomas, V. K., Dustin, M. L., Kam, L. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Micropatterning+of+costimulatory+ligands+enhances+CD4++T+cell+function.">Micropatterning of costimulatory ligands enhances CD4+ T cell function.</a> Proceedings of the National Academy of Sciences. 105, 7791-7791 (2008).</li><li>Shi, P., Shen, K., Kam, L. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Local+presentation+of+L1+and+N-cadherin+in+multicomponent,+microscale+patterns+differentially+direct+neuron+function+in+vitro.">Local presentation of L1 and N-cadherin in multicomponent, microscale patterns differentially direct neuron function in vitro.</a> Developmental Neurobiology. 67, 1765-1765 (2007).</li></ol>

The authors have nothing to disclose.

The microcontact printing process is conceptually simple and very robust, having been applied to patterning a wide range of molecules on a variety of substrates. However, this process remains something of an art. The specific geometry of the pattern to be created, protein to be patterned, applied weight, and coating/stamping conditions all affect the stamping quality. For example, too little weight, applied to large features, often results in gaps in the pattern as can be seen in the upper right logo of Fig. 1A. Converse...

<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="http://www.w3.org/1999/xhtml" xml:lang="en" lang="en">	
		
		<div>
		<table border="1">
		<thead>
		<tr>
		<th>Material Name</th>
		<th>Type</th>
		<th>Company</th>
		<th>Catalogue Number</th>
		<th>Comment</th>
		</tr>
		</thead>
		<tbody>
		
<tr>
<td>Plasma Cleaner</td>
<td>&nbsp;</td>
<td>Harrick Scientific Products, Inc.</td>
<td>PDC-32G</td>
<td>&nbsp;</td>
<tr>
<td>Desiccator</td>
<td>&nbsp;</td>
<td>Nalgene</td>
<td>5315-0150</td>
<td>&nbsp;</td>
<tr>
<td>PBS</td>
<td>Reagent</td>
<td>Invitrogen</td>
<td>10010-072</td>
<td>&nbsp;</td>
<tr>
<td>Protein labeling kit</td>
<td>Reagent</td>
<td>Invitrogen</td>
<td>A30006</td>
<td>&nbsp;</td>
<tr>
<td>Fibronectin </td>
<td>Reagent</td>
<td>Sigma-Aldrich</td>
<td>F2006</td>
<td>&nbsp;</td>
<tr>
<td>Staining rack</td>
<td>Reagent</td>
<td>Thomas Scientific</td>
<td>8542E40</td>
<td>&nbsp;</td>
<tr>
<td>Coverslips</td>
<td>Reagent</td>
<td>Fisher Scientific</td>
<td>12-544-12</td>
<td>&nbsp;</td>
<tr>
<td>Sylgard 184</td>
<td>Reagent</td>
<td>Ellsworth Adhesives</td>
<td>184 Sil Elast Kit</td>
<td>&nbsp;</td>
<tr>
<td>Diffraction Grating</td>
<td>Reagent</td>
<td>Edmund Scientific</td>
<td>3040267</td>
<td>&nbsp;</td>		</tbody>
		</table>
		</div>

microcontact printing of proteins for cell biology

The ability to pattern proteins and other biomolecules onto substrates is important for capturing the spatial complexity of the extracellular environment. Development of microcontact printing by the Whitesides group (<a href="http://gmwgroup.harvard.edu/">http://gmwgroup.harvard.edu/</a>) in the mid-1990s revolutionalized this field by making microelectronics/microfabrication techniques accessible to laboratories focused on the life sciences. Initial implementations of this method used polydimethylsiloxane (PDMS) stamps to create patterns of functionalized chemicals on material surfaces1. Since then, a range of innovative approaches have been developed to pattern other molecules, including proteins2. This video demonstrates the basic process of creating PDMS stamps and uses them to pattern proteins, as these steps are difficult to accurately express in words. We focus on patterning the extracellular matrix protein fibronectin onto glass coverslips as a specific example of patterning.
An important component of the microcontact printing process is a topological master, from which the stamps are cast; the raised and lowered regions of the master are mirrored into the stamp and define the final pattern. Typically, a master consists of a silicon wafer coated with photoresist and then patterned by photolithography, as is done here. Creation of masters containing a specific pattern requires specialized equipment, and is best approached in consultation with a fabrication center or facility. However, almost any substrate with topology can be used as a master, such as plastic diffraction gratings (see Reagents for one example), and such serendipitous masters provide readily available, simple patterns. This protocol begins at the point of having a master in hand.

Watch this Scientific Journal Video about Microcontact Printing of Proteins for Cell Biology at JoVE.com

Microcontact Printing of Proteins for Cell Biology

Microcontact printing is used extensively to pattern proteins and other molecules on material surfaces. We demonstrate the basic steps of this process, stamping patterns of fibronectin onto glass.

The ability to pattern proteins and other biomolecules onto substrates is important for capturing the spatial complexity of the extracellular environment. ...

microcontact-printing-of-proteins-for-cell-biology

Research

JoVE Journal

Biology

19.9K 조회수.  Columbia University. Microcontact 인쇄는 소재 표면에 패턴 단백질 및 다른 분자로 광범위하게 사용됩니다. 우리는 유리에 fibronectin의 패턴을 스탬핑,이 과정의 기본 단계를 보여줍니다.

비디오: Microcontact Printing of Proteins for Cell Biology

A Gradient-generating Microfluidic Device for Cell Biology

 The fabrication and operation of a gradient-generating microfluidic device for studying cellular behavior is described.  A microfluidic platform is an enabling experimental tool, because it can precisely manipulate fluid flows, enable high-throughput experiments, and generate stable soluble concentration gradients.  Compared to conventional gradient generators, poly(dimethylsiloxane) (PDMS)-based  microfluidic devices can generate stable concentration gradients of growth factors with well-defined profiles.  Here, we developed simple gradient-generating microfluidic devices with three separate inlets.  Three microchannels combined into one microchannel to generate concentration gradients.  The stability and shape of growth factor gradients were confirmed by fluorescein isothyiocyanate (FITC)-dextran with a molecular weight similar to epidermal growth factor (EGF).  Using this microfluidic device, we demonstrated that fibroblasts exposed to concentration gradients of EGF migrated toward higher concentrations.  The directional orientation of cell migration and motility of migrating cells were quantitatively assessed by cell tracking analysis.  Thus, this gradient-generating microfluidic device might be useful for studying and analyzing the behavior of migrating cells.

We describe a protocol for the microfabrication of the gradient-generating microfluidic device that can generate spatial and temporal gradients in well-defined microenvironment. In this approach, the gradient-generating microfluidic device can be used to study directed cell migration, embryogenesis, wound healing, and cancer metastasis.

 The fabrication and operation of a gradient-generating microfluidic device for studying cellular behavior is described.  A microfluidic platform is an ...

Micro-scale Engineering for Cell Biology

Assessing Two-dimensional Crystallization Trials of Small Membrane Proteins for Structural Biology Studies by Electron Crystallography

Electron crystallography has evolved as a method that can be used either alternatively or in combination with three-dimensional crystallization and X-ray crystallography to study structure-function questions of membrane proteins, as well as soluble proteins. Screening for two-dimensional (2D) crystals by transmission electron microscopy (EM) is the critical step in finding, optimizing, and selecting samples for high-resolution data collection by cryo-EM. Here we describe the fundamental steps in identifying both large and ordered, as well as small 2D arrays, that can potentially supply critical information for optimization of crystallization conditions.
By working with different magnifications at the EM, data on a range of critical parameters is obtained. Lower magnification supplies valuable data on the morphology and membrane size. At higher magnifications, possible order and 2D crystal dimensions are determined. In this context, it is described how CCD cameras and online-Fourier Transforms are used at higher magnifications to assess proteoliposomes for order and size.
While 2D crystals of membrane proteins are most commonly grown by reconstitution by dialysis, the screening technique is equally applicable for crystals produced with the help of monolayers, native 2D crystals, and ordered arrays of soluble proteins. In addition, the methods described here are applicable to the screening for 2D crystals of even smaller as well as larger membrane proteins, where smaller proteins require the same amount of care in identification as our examples and the lattice of larger proteins might be more easily identifiable at earlier stages of the screening.

Evaluating two-dimensional (2D) crystallization trials for the formation of ordered membrane protein arrays is a highly critical and difficult task in electron crystallography. Here we describe our approach in screening for and identifying 2D crystals of predominantly small membrane proteins in the range of 15 &#x2013; 90kDa.

Electron crystallography has evolved as a method that can be used either alternatively or in combination with three-dimensional crystallization and X-ray ...

Fluorescent Labeling of COS-7 Expressing SNAP-tag Fusion Proteins for Live Cell Imaging

SNAP-tag and CLIP-tag protein labeling systems enable the specific, covalent attachment of molecules, including fluorescent dyes, to a protein of interest in live cells. These systems offer a broad selection of fluorescent substrates optimized for a range of imaging instrumentation. Once cloned and expressed, the tagged protein can be used with a variety of substrates for numerous downstream applications without having to clone again. There are two steps to using this system: cloning and expression of the protein of interest as a SNAP-tag fusion, and labeling of the fusion with the SNAP-tag substrate of choice. The SNAP-tag is a small protein based on human O6-alkylguanine-DNA-alkyltransferase (hAGT), a DNA repair protein. SNAP-tag labels are dyes conjugated to guanine or chloropyrimidine leaving groups via a benzyl linker. In the labeling reaction, the substituted benzyl group of the substrate is covalently attached to the SNAP-tag. CLIP-tag is a modified version of SNAP-tag, engineered to react with benzylcytosine rather than benzylguanine derivatives. When used in conjunction with SNAP-tag, CLIP-tag enables the orthogonal and complementary labeling of two proteins simultaneously in the same cells.

SNAP-tag and CLIP-tag protein labeling systems enable the specific, covalent attachment of molecules, including fluorescent dyes, to a protein of interest in live cells. Once cloned and expressed, the tagged protein can be used with a variety of substrates for numerous downstream applications without having to clone again.

SNAP-tag and CLIP-tag protein labeling systems enable the specific, covalent attachment of molecules, including fluorescent dyes, to a protein of interest ...

Protein Membrane Overlay Assay: A Protocol to Test Interaction Between Soluble and Insoluble Proteins in vitro

Validating interactions between different proteins is vital for investigation of their biological functions on the molecular level. There are several methods, both in vitro and in vivo, to evaluate protein binding, and at least two methods that complement the shortcomings of each other should be conducted to obtain reliable insights. 
For an in vivo assay, the bimolecular fluorescence complementation (BiFC) assay represents the most popular and least invasive approach that enables to detect protein-protein interaction within living cells, as well as identify the intracellular localization of the interacting proteins 1,2. In this assay, non-fluorescent N- and C-terminal halves of GFP or its variants are fused to tested proteins, and when the two fusion proteins are brought together due to the tested proteins&#x2019; interactions, the fluorescent signal is reconstituted3-6. Because its signal is readily detectable by epifluorescence or confocal microscopy, BiFC has emerged as a powerful tool of choice among cell biologists for studying about protein-protein interactions in living cells 3. This assay, however, can sometimes produce false positive results. For example, the fluorescent signal can be reconstituted by two GFP fragments arranged as far as 7 nm from each other due to close packing in a small subcellular compartment, rather that due to specific interactions7.
Due to these limitations, the results obtained from live cell imaging technologies should be confirmed by an independent approach based on a different principle for detecting protein interactions. Co-immunoprecipitation (Co-IP) or glutathione transferase (GST) pull-down assays represent such alternative methods that are commonly used to analyze protein-protein interactions in vitro. However, iIn these assays, however, the tested proteins must be readily soluble in the buffer that supportsused for the binding reaction. Therefore, specific interactions involving an insoluble protein cannot be assessed by these techniques.
 Here, we illustrate the protocol for the protein membrane overlay binding assay, which circumvents this difficulty. In this technique, interaction between soluble and insoluble proteins can be reliably tested because one of the proteins is immobilized on a membrane matrix. This method, in combination with in vivo experiments, such as BiFC, provides a reliable approach to investigate and characterize interactions faithfully between soluble and insoluble proteins. In this article, binding between Tobacco mosaic virus (TMV) movement protein (MP), which exerts multiple functions during viral cell-to-cell transport8-14, and a recently identified plant cellular interactor, tobacco ankyrin repeat-containing protein (ANK) 15, is demonstrated using this technique.

Protein Membrane Overlay Assay: A Protocol to Test Interaction Between Soluble and Insoluble Proteins in vitro

Testing protein-protein interaction is indispensable for dissection of protein functionality. Here, we introduce an in vitro protein-protein binding assay to probe a membrane-immobilized protein with a soluble protein. This assay provides a reliable method to test interaction between an insoluble protein and a protein in solution.

Validating interactions between different proteins is vital for investigation of their biological functions on the molecular level.  There are several ...

Pull-down of Calmodulin-binding Proteins

Calcium (Ca2+) is an ion vital in regulating cellular function through a variety of mechanisms. Much of Ca2+ signaling is mediated through the calcium-binding protein known as calmodulin (CaM)1,2. CaM is involved at multiple levels in almost all cellular processes, including apoptosis, metabolism, smooth muscle contraction, synaptic plasticity, nerve growth, inflammation and the immune response. A number of proteins help regulate these pathways through their interaction with CaM. Many of these interactions depend on the conformation of CaM, which is distinctly different when bound to Ca2+ (Ca2+-CaM) as opposed to its Ca2+-free state (ApoCaM)3.
While most target proteins bind Ca2+-CaM, certain proteins only bind to ApoCaM. Some bind CaM through their IQ-domain, including neuromodulin4, neurogranin (Ng)5, and certain myosins6. These proteins have been shown to play important roles in presynaptic function7, postsynaptic function8, and muscle contraction9, respectively. Their ability to bind and release CaM in the absence or presence of Ca2+ is pivotal in their function. In contrast, many proteins only bind Ca2+-CaM and require this binding for their activation. Examples include myosin light chain kinase10, Ca2+/CaM-dependent kinases (CaMKs)11 and phosphatases (e.g. calcineurin)12, and spectrin kinase13, which have a variety of direct and downstream effects14.
The effects of these proteins on cellular function are often dependent on their ability to bind to CaM in a Ca2+-dependent manner. For example, we tested the relevance of Ng-CaM binding in synaptic function and how different mutations affect this binding. We generated a GFP-tagged Ng construct with specific mutations in the IQ-domain that would change the ability of Ng to bind CaM in a Ca2+-dependent manner. The study of these different mutations gave us great insight into important processes involved in synaptic function8,15. However, in such studies, it is essential to demonstrate that the mutated proteins have the expected altered binding to CaM.
Here, we present a method for testing the ability of proteins to bind to CaM in the presence or absence of Ca2+, using CaMKII and Ng as examples. This method is a form of affinity chromatography referred to as a CaM pull-down assay. It uses CaM-Sepharose beads to test proteins that bind to CaM and the influence of Ca2+ on this binding. It is considerably more time efficient and requires less protein relative to column chromatography and other assays. Altogether, this provides a valuable tool to explore Ca2+/CaM signaling and proteins that interact with CaM.

Calmodulin (CaM) pull-down assay is an effective way to investigate the interaction of CaM with various proteins. This method uses CaM-sepharose beads for efficient and specific analysis of CaM-binding proteins. This provides an important tool to explore CaM signaling in cellular function.

Calcium (Ca2+) is an ion vital in regulating cellular function through a variety of mechanisms. Much of Ca2+ signaling is mediated through the ...

Modified Yeast-Two-Hybrid System to Identify Proteins Interacting with the Growth Factor Progranulin

Progranulin (PGRN), also known as granulin epithelin precursor (GEP), is a 593-amino-acid autocrine growth factor. PGRN is known to play a critical role in a variety of physiologic and disease processes, including early embryogenesis, wound healing 1, inflammation 2, 3, and host defense 4. PGRN also functions as a neurotrophic factor 5, and mutations in the PGRN gene resulting in partial loss of the PGRN protein cause frontotemporal dementia 6, 7. Our recent studies have led to the isolation of PGRN as an important regulator of cartilage development and degradation 8-11. Although PGRN, discovered nearly two decades ago, plays crucial roles in multiple physiological and pathological conditions, efforts to exploit the actions of PGRN and understand the mechanisms involved have been significantly hampered by our inability to identify its binding receptor(s). To address this issue, we developed a modified yeast two-hybrid (MY2H) approach based on the most commonly used GAL4 based 2-hybrid system. Compared with the conventional yeast two-hybrid screen, MY2H dramatically shortens the screen process and reduces the number of false positive clones. In addition, this approach is reproducible and reliable, and we have successfully employed this system in isolating the binding proteins of various baits, including ion channel 12, extracellular matrix protein 10, 13, and growth factor14. In this paper, we describe this MY2H experimental procedure in detail using PGRN as an example that led to the identification of TNFR2 as the first known PGRN-associated receptor 14, 15.

We have modified the conventional yeast two-hybrid screening, an effective genetic tool in identifying protein interaction. This modification markedly shortens the process, reduces the workload, and most importantly, reduces the number of false positives. In addition, this approach is reproducible and reliable.

Progranulin (PGRN), also known as granulin epithelin precursor (GEP), is a 593-amino-acid autocrine growth factor. PGRN is known to play a critical role ...

Cell Tracking Using Photoconvertible Proteins During Zebrafish Development

Embryogenesis is a dynamic process that is best studied by using techniques that allow the documentation of developmental changes in vivo. The use of genetically-encoded fluorescent proteins has proven a valuable strategy for elucidating dynamic morphogenetic processes as they occur in the intact organism. During the past decade, the development of photoactivatable and photoconvertible fluorescent proteins has opened the possibility to investigate the fate of discrete subpopulations of tagged proteins1. Unlike photoactivatable proteins, photoconvertible fluorescent proteins (PCFPs) are readily tracked and imaged in their native emission state prior to photoconversion, making it easier to identify and select regions by optical inspection. PCFPs, such as Kaede2, KikGR3, Dendra4 and EosFP5, can be shifted from green to red upon exposure to UV or blue light due to a His-Tyr-Gly tripeptide sequence which forms a green chromophore that can be photoconverted to a red one by a light-catalyzed &beta;-elimination and subsequent extension of a &pi;-conjugated system3. PCFPs and their monomeric variants are useful tools for tracking cells6-10 and studying protein dynamics11-14, respectively. During recent years, PCFPs have been expressed in different animal model, such as zebrafish6, chicken7,8 and mouse9,10 for cell fate tracking. Here we report a protocol for cell-specific photoconversion of PCFPs in the living zebrafish embryo and further tracking of photoconverted proteins at later developmental stages. This methodology allows studying, in a tissue-specific manner, cell biological events underlying morphogenesis in the zebrafish animal model.

Here, we present a method for the photoactivated switch of photoconvertible fluorescent proteins (PCFPs) in the living zebrafish embryo and further tracking of photoconverted protein at specific time points during development. This methodology allows monitoring of cell biological events underlying different developmental processes in a live vertebrate organism.

Embryogenesis is a dynamic process that is best studied by using techniques that allow the documentation of developmental changes in vivo. The use of ...

The Use of Chemostats in Microbial Systems Biology

Cells regulate their rate of growth in response to signals from the external world. As the cell grows, diverse cellular processes must be coordinated including macromolecular synthesis, metabolism and ultimately, commitment to the cell division cycle. The chemostat, a method of experimentally controlling cell growth rate, provides a powerful means of systematically studying how growth rate impacts cellular processes - including gene expression and metabolism - and the regulatory networks that control the rate of cell growth. When maintained for hundreds of generations chemostats can be used to study adaptive evolution of microbes in environmental conditions that limit cell growth. We describe the principle of chemostat cultures, demonstrate their operation and provide examples of their various applications. Following a period of disuse after their introduction in the middle of the twentieth century, the convergence of genome-scale methodologies with a renewed interest in the regulation of cell growth and the molecular basis of adaptive evolution is stimulating a renaissance in the use of chemostats in biological research.

Cell growth rate is a regulated process and a primary determinant of cell physiology. Continuous culturing using chemostats enables extrinsic control of cell growth rate by nutrient limitation facilitating the study of molecular networks that control cell growth and how those networks evolve to optimize cell growth.

Cells regulate their rate of growth in response to signals from the external world. As the cell grows, diverse cellular processes must be coordinated ...

Protocols for Implementing an Escherichia coli Based TX-TL Cell-Free Expression System for Synthetic Biology

Ideal cell-free expression systems can theoretically emulate an in vivo cellular environment in a controlled in vitro platform.1 This is useful for expressing proteins and genetic circuits in a controlled manner as well as for providing a prototyping environment for synthetic biology.2,3 To achieve the latter goal, cell-free expression systems that preserve endogenous Escherichia coli transcription-translation mechanisms are able to more accurately reflect in vivo cellular dynamics than those based on T7 RNA polymerase transcription. We describe the preparation and execution of an efficient endogenous E. coli based transcription-translation (TX-TL) cell-free expression system that can produce equivalent amounts of protein as T7-based systems at a 98% cost reduction to similar commercial systems.4,5 The preparation of buffers and crude cell extract are described, as well as the execution of a three tube TX-TL reaction. The entire protocol takes five days to prepare and yields enough material for up to 3000 single reactions in one preparation. Once prepared, each reaction takes under 8 hr from setup to data collection and analysis. Mechanisms of regulation and transcription exogenous to E. coli, such as lac/tet repressors and T7 RNA polymerase, can be supplemented.6 Endogenous properties, such as mRNA and DNA degradation rates, can also be adjusted.7 The TX-TL cell-free expression system has been demonstrated for large-scale circuit assembly, exploring biological phenomena, and expression of proteins under both T7- and endogenous promoters.6,8 Accompanying mathematical models are available.9,10 The resulting system has unique applications in synthetic biology as a prototyping environment, or "TX-TL biomolecular breadboard."

Protocols for Implementing an Escherichia coli Based TX-TL Cell-Free Expression System for Synthetic Biology

This five-day protocol outlines all steps, equipment, and supplemental software necessary for creating and running an efficient endogenous Escherichia coli based TX-TL cell-free expression system from scratch. With reagents, the protocol takes 8 hours or less to setup a reaction, collect, and process data.

Ideal cell-free expression systems can theoretically emulate an in vivo cellular environment in a controlled in vitro platform.1 This is useful for ...