This study was supported by the grant from AACP New Pharmacy Faculty Research Award Program, Medical Research Foundation of Oregon New Investigator Grant, Oregon State University-Startup fund, and Pacific University, School of Pharmacy Start-up fund.

1. Preparation of Individual and Multi-drug Loaded Micelles by Solvent Casting Method
<ol>
	<li>Weigh out DTX 1 mg or EVR 1 mg or both drugs at 1 mg each for the dual drug micelles (DDM).</li>
	<li>Weigh out 15 mg of PEG2000-b-PLA1800 or PEG4000-b-PLA2200 for either individual or DDM.</li>
	<li>Dissolve the drug/ drugs and the polymer in 0.5 ml of acetonitrile and place in a 5 ml round bottom flask.</li>
	<li>Form a thin drug distributed polymer film by evaporating the drug(s)-polymer acetonitrile solution under reduced pressure using a rotary evaporator. Set the rotary evaporator to 100 rpm, the water bath temperature of 40 oC and a vacuum pressure of 260 mbar for 5 min followed by a reduction to 100 mbar for 3 more min.</li>
	<li>Rehydrate the drug-polymer film with 0.5 ml of deionized water at 50 oC and gently shake the flask to form the micelles.</li>
	<li>Filter the resulting micellar solution through a 0.2 &#181;m nylon filter to remove any un-dissolved drug or contaminants into a 1.5 ml centrifuge tube.</li>
</ol>
2. Assessment of Drug Loading and Stability in Micelles Using Reverse-phase High Performance Liquid Chromatography (RP-HPLC)
<ol>
	<li>Perform RP-HPLC analysis with a C8 column equilibriated at 40 &#176;C in an isocratic mode with a mobile phase of acetonitrile/water (62/38) containing 0.1% phosphoric acid and 1% methanol at a flow rate of 1 ml/min and an injection volume of 10 &#181;l.</li>
	<li>Dilute freshly prepared micelles (section 1) 1:100 in mobile phase prior to analyzing by RP-HPLC to determine initial drug loading. Store undiluted individual micelles and DDM at room temperature (25 oC) for 48 hr and prepare fresh 1:100 diluted samples in mobile phase to re-assess by RP-HPLC and determine drug(s) stability in micelles over 24 hr.</li>
	<li>Monitor DTX and EVR peaks at 227 and 279 nm respectively with retention times of 1.7 and 5.7 min respectively. Perform all measurements in triplicate. Present data as Mean &#177; SD drug loading.</li>
</ol>
3. Assessment of micelle Particle Size by Dynamic Light Scattering (DLS)
<ol>
	<li>Dilute freshly prepared micelles (as described in section 1) in deionized water at a ratio of 1:20 to yield a final polymer concentration of 1.5 mg/ml.</li>
	<li>Measure the intensity of He-Ne laser (633 nm) at 173&#176; to determine scattering. Perform all measurements at 25 &#176;C following pre-equilibration for 2 min.</li>
	<li>Perform all measurements in triplicate. Present data as the Mean Z-average size &#177; SD along with the polydispersity index (PDI) of the distribution.</li>
</ol>
4. Assessment of In Vitro Drug Release from Individual Micelles and DDM
<ol>
	<li>Prepare individual micelles and DDM as described in section 1. Load 2.5 ml of the micelles into a 3 ml dialysis cassette with a molecular weight cut-off (MWCO) of 7,000 g/mol. 
	NOTE: This MWCO was chosen to enable the free drug(s) along with the unassociated polymer molecules to diffuse freely out of the cassette and thereby ensure sink conditions.</li>
	<li>Place the cassettes in 2.5 L of 10 mM pH 7.4 phosphate buffer (prepared by diluting stock 200 mM solution) and change the buffer every 3 hr to ensure sink conditions. Maintain the temperature of the buffer at 37 oC throughout the duration of the experiment.</li>
	<li>At 0, 0.5, 1, 2, 3, 6, 9, 12, 24, and 48 hr, withdraw 150 &#181;l of the solution in the cassettes and replace with 150 &#181;l of fresh buffer.</li>
	<li>Analyze the samples using RP-HPLC as established in section 2 to determine the drug concentration. Curve-fit the drug(s) release data based on a simple diffusion model with a one phase exponential association using stastitical software.</li>
	<li>Calculate the time needed to reach 50% of drug release (t1/2) of each drug in individual micelles or DDM based on the curve fitting. Perform all measurements in quadruplet.</li>
</ol>

<ol>
	<li>Yokoyama, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Polymeric+micelles+as+a+new+drug+carrier+system+and+their+required+considerations+for+clinical+trials.">Polymeric micelles as a new drug carrier system and their required considerations for clinical trials.</a> Expert Opin Drug Deliv. 7, 145-158 (2010).</li><li>Shin, H. C., Alani, A. W., Rao, D. A., Rockich, N. C., Kwon, G. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Multi-drug+loaded+polymeric+micelles+for+simultaneous+delivery+of+poorly+soluble+anticancer+drugs.">Multi-drug loaded polymeric micelles for simultaneous delivery of poorly soluble anticancer drugs.</a> J Control Release. 140, 294-300 (2009).</li><li>Adams, M. L., Lavasanifar, A., Kwon, G. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Amphiphilic+block+copolymers+for+drug+delivery.">Amphiphilic block copolymers for drug delivery.</a> J Pharm Sci. 92, 1343-1355 (2003).</li><li>Oerlemans, C., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Polymeric+micelles+in+anticancer+therapy:+targeting,+imaging+and+triggered+release.">Polymeric micelles in anticancer therapy: targeting, imaging and triggered release.</a> Pharm Res. 27, 2569-2589 (2010).</li><li>Shin, H. C., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+3-in-1+polymeric+micelle+nanocontainer+for+poorly+water-soluble+drugs.">A 3-in-1 polymeric micelle nanocontainer for poorly water-soluble drugs.</a> Mol Pharm. 8, 1257-1265 (2011).</li><li>Hasenstein, J. R., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Antitumor+activity+of+Triolimus:+a+novel+multidrug-loaded+micelle+containing+Paclitaxel+Rapamycin,+and+17-AAG.">Antitumor activity of Triolimus: a novel multidrug-loaded micelle containing Paclitaxel Rapamycin, and 17-AAG.</a> Mol Cancer Ther. 11, 2233-2242 (2012).</li><li>Mazzaferro, S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Bivalent+sequential+binding+of+docetaxel+to+methyl-beta-cyclodextrin.">Bivalent sequential binding of docetaxel to methyl-beta-cyclodextrin.</a> Int J Pharm. 416, 171-180 (2011).</li><li>Iwase, Y., Maitani, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Preparation+and+in+vivo+evaluation+of+liposomal+everolimus+for+lung+carcinoma+and+thyroid+carcinoma.">Preparation and in vivo evaluation of liposomal everolimus for lung carcinoma and thyroid carcinoma.</a> Biol Pharm Bull. 35, 975-979 (2012).</li><li>Mishra, G. P., Doddapaneni, B. S., Nguyen, D., Alani, A. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Antiangiogenic+effect+of+docetaxel+and+everolimus+as+individual+and+dual-drug-loaded+micellar+nanocarriers.">Antiangiogenic effect of docetaxel and everolimus as individual and dual-drug-loaded micellar nanocarriers.</a> Pharm Res. 31, 660-669 (2014).</li><li>Xu, W., Ling, P., Zhang, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Polymeric+micelles,+a+promising+drug+delivery+system+to+enhance+bioavailability+of+poorly+water-soluble+drugs.">Polymeric micelles, a promising drug delivery system to enhance bioavailability of poorly water-soluble drugs.</a> J Drug Deliv. 2013, 340315 (2013).</li><li>Lavasanifar, A., Samuel, J., Kwon, G. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Poly(ethylene+oxide)-block-poly(L-amino+acid)+micelles+for+drug+delivery.">Poly(ethylene oxide)-block-poly(L-amino acid) micelles for drug delivery.</a> Adv Drug Deliv Rev. 54, 169-190 (2002).</li></ol>

The authors have nothing to disclose.

The use of polymeric micelles for drug delivery continues to expand due to their versatility and ability to deliver hydrophobic drugs for various disease states. Therefore, the techniques needed to prepare and characterize these formulations prior to use in cell culture or animals is a critical first step to determine the best pairing between the drug and the polymer. PEG-b-PLA are excellent amphiphilic block copolymers for drug delivery purposes. However, the block length of the hydrophilic and hydrophobic s...

Amphiphilic block copolymers with repeating structure composed of hydrophilic and hydrophobic domains can spontaneously self-assemble to form three dimensional macromolecular assemblies known as polymeric micelles. These structures have an inner hydrophobic core surrounded by a hydrophilic shell. The hydrophobic core has the ability to incorporate hydrophobic drugs either by physical entrapment through hydrophobic interactions or by chemical conjugation on to the polymer backbone.1 Many advantages exist to using these block copolymers to form micelles for drug delivery. These include incorporation of poorly soluble drugs, improving pharmacokinetics of the incorporated drugs, and the biocompatibility and/or biodegradability of the polymers makes them a safe alternate to conventional solubilizers.2 Another advantage of using polymeric micelles is their colloidal particle size, between 15&#8211;150 nm3, making them attractive for parenteral delivery. Therefore, over the last 20 years polymeric micelles have emerged as viable drug delivery systems for poorly water-soluble drugs especially for cancer therapy.3,4
Currently there are five polymeric micellar formulations for cancer therapy undergoing clinical trials.4 Four of the micelles in the clinical trials are PEG-based diblock copolymers while the last is a triblock copolymer containing polyethyleneoxide. The size of these micelles varied from 20 nm to 85 nm. The advantage of using PEG based polymers is their biocompatibility and depending on the second block can also be biodegradable. Recently new drug delivery systems based on polyethyleneglycol-block-polylactic acid (PEG-b-PLA) polymeric micelles have been developed for the concurrent delivery of multiple anticancer drugs. The PEG-b-PLA micelles are both biocompatible and biodegradable. These multi-drug loaded micelles have shown a synergistic inhibition of different cancers models in vitro and in vivo2,5,6 and fit into the current paradigm of utilizing multiple drugs in chemotherapy to prevent resistance and lowering toxicity. Therefore, there is a great deal of interest in preparing and characterizing these micellar drug delivery systems for use in cancer and other disease states.
In the work below we have outlined a step-by-step process by which such micelles can be prepared and characterized before evaluating them in disease states of interest. For the purpose of this work two poorly-soluble anti-cancer agents, docetaxel (DTX) and everolimus (EVR) have been chosen. Both DTX and EVR are poorly water-soluble compounds with intrinsic water solubilities at 1.9 and 9.6 &#181;g/ml respectively.7,8 Two PEG-b-PLA polymers with different molecular weights were used in this protocol as the building blocks for the formulated polymeric micelles, these polymers are PEG2000-b-PLA1800 (3,800 Da) and PEG4000-b-PLA2200 (6,200 Da). PEG-b-PLA micelles can therefore provide a unique platform as a nanocarrier for DTX and EVR individually and in combination. The required Reagents/Materials and Equipment needed to prepare and characterize these micelles are listed in Table 1.

<table border="0" cellpadding="0" cellspacing="0">
	<tbody>
		<tr>
			<td>PEG2000-b-PLA1800</td>
			<td>Advanced Polymer Materials, Inc</td>
			<td>6-01- PLA/2000</td>
			<td>PLA MW can be specified on ordering</td>
		</tr>
		<tr>
			<td>PEG4000-b-PLA2200</td>
			<td>Advanced Polymer Materials, Inc</td>
			<td>6-01- PLA/4000</td>
			<td>PLA MW can be specified on ordering</td>
		</tr>
		<tr>
			<td>Docetaxel</td>
			<td>LC Laboratories</td>
			<td>D-1000</td>
			<td>100 mg</td>
		</tr>
		<tr>
			<td>Everolimus</td>
			<td>LC Laboratories</td>
			<td>E-4040</td>
			<td>100 mg</td>
		</tr>
		<tr>
			<td>Acetonitrile</td>
			<td>EMD/VWR</td>
			<td>EM-AX0145-1</td>
			<td>HPLC grade; 4 L</td>
		</tr>
		<tr>
			<td>Round bottom flask&#160;</td>
			<td>Glassco/VWR</td>
			<td>89426-496</td>
			<td>5 mL</td>
		</tr>
		<tr>
			<td>RV 10 Control Rotary Evaporators</td>
			<td>IKA Works</td>
			<td>8025001</td>
			<td>Rotoevaporator</td>
		</tr>
		<tr>
			<td>Shimadzhu HPLC with DAD detector</td>
			<td>Shimadzhu</td>
			<td></td>
			<td>RP-HPLC</td>
		</tr>
		<tr>
			<td>Slide-a-lyzer dialysis casette MWCO 7000</td>
			<td>Thermo Scientific, Inc</td>
			<td>66370</td>
			<td>3 mL</td>
		</tr>
		<tr>
			<td>Phosphate buffer pH 7.4 200 mM</td>
			<td>VWR</td>
			<td>100190-870</td>
			<td>500 mL</td>
		</tr>
		<tr>
			<td>Malvern NanoZS</td>
			<td>Malvern Instruments, UK</td>
			<td></td>
			<td>DLS</td>
		</tr>
		<tr>
			<td>Nylon filter</td>
			<td>Acrodisc/VWR</td>
			<td>28143-242</td>
			<td>13 mm; 0.2&#181;M</td>
		</tr>
		<tr>
			<td>Phosphoric acid, NF</td>
			<td>Spectrum Chemical/VWR</td>
			<td>700000-626</td>
			<td>100 mL</td>
		</tr>
		<tr>
			<td>GraphPad Prism</td>
			<td><a href="http://www.graphpad.com/">www.graphpad.com</a></td>
			<td></td>
			<td>Analysis software</td>
		</tr>
		<tr>
			<td>Zorbax SB-C8 Rapid Resolution cartridge&#160;</td>
			<td>Agilent Technologies</td>
			<td>866953-906</td>
			<td>4.6 &#215;75mm, 3.5 micron</td>
		</tr>
	</tbody>
</table>

preparation and characterization of individual and multi-drug loaded physically entrapped polymeric micelles

Amphiphilic block copolymers like polyethyleneglycol-block-polylactic acid (PEG-b-PLA) can self-assemble into micelles above their critical micellar concentration forming hydrophobic cores surrounded by hydrophilic shells in aqueous environments. The core of these micelles can be utilized to load hydrophobic, poorly water soluble drugs like docetaxel (DTX) and everolimus (EVR). Systematic characterization of the micelle structure and drug loading capabilities are important before in vitro and in vivo studies can be conducted. The goal of the protocol described herein is to provide the necessary characterization steps to achieve standardized micellar products. DTX and EVR have intrinsic solubilities of 1.9 and 9.6 &#181;g/ml respectively Preparation of these micelles can be achieved through solvent casting which increases the aqueous solubility of DTX and EVR to 1.86 and 1.85 mg/ml, respectively. Drug stability in micelles evaluated at room temperature over 48 hr indicates that 97% or more of the drugs are retained in solution. Micelle size was assessed using dynamic light scattering and indicated that the size of these micelles was below 50 nm and depended on the molecular weight of the polymer. Drug release from the micelles was assessed using dialysis under sink conditions at pH 7.4 at 37 oC over 48 hr. Curve fitting results indicate that drug release is driven by a first order process indicating that it is diffusion driven.

Individual DTX or EVR micelles and DTX and EVR DDM in PEG-b-PLA micelles are successfully formulated in either PEG4000-b-PLA2200 or PEG2000-b-PLA1800 (Figure 1).
DTX, EVR, and the DDM showed similar stability in PEG4000-b-PLA2200 or PEG2000-b-PLA1800 over 48 hr (Figure 2). Initial drug loading of EVR in PEG4000-b</...

Watch this Scientific Journal Video about Preparation and Characterization of Individual and Multi-drug Loaded Physically Entrapped Polymeric Micelles at JoVE.com

Preparation and Characterization of Individual and Multi-drug Loaded Physically Entrapped Polymeric Micelles

The goal of this protocol is to describe the preparation and characterization of physically entrapped, poorly water soluble drugs in micellar drug delivery systems composed of amphiphilic block copolymers.

Amphiphilic block copolymers like polyethyleneglycol-block-polylactic acid (PEG-b-PLA) can self-assemble into micelles above their critical micellar ...

preparation-characterization-individual-multi-drug-loaded-physically

Research

JoVE Journal

Chemistry

11.2K 조회수.  Pacific University. The goal of this protocol is to describe the preparation and characterization of physically entrapped, poorly water soluble drugs in micellar drug delivery systems composed of amphiphilic block copolymers.

비디오: Preparation and Characterization of Individual and Multi-drug Loaded Physically Entrapped Polymeric Micelles

Split-and-pool Synthesis and Characterization of Peptide Tertiary Amide Library

Peptidomimetics are great sources of protein ligands. The oligomeric nature of these compounds enables us to access large synthetic libraries on solid phase by using combinatorial chemistry. One of the most well studied classes of peptidomimetics is peptoids. Peptoids are easy to synthesize and have been shown to be proteolysis-resistant and cell-permeable. Over the past decade, many useful protein ligands have been identified through screening of peptoid libraries. However, most of the ligands identified from peptoid libraries do not display high affinity, with rare exceptions. This may be due, in part, to the lack of chiral centers and conformational constraints in peptoid molecules. Recently, we described a new synthetic route to access peptide tertiary amides (PTAs). PTAs are a superfamily of peptidomimetics that include but are not limited to peptides, peptoids and N-methylated peptides. With side chains on both &#945;-carbon and main chain nitrogen atoms, the conformation of these molecules are greatly constrained by sterical hindrance and allylic 1,3 strain. (Figure 1) Our study suggests that these PTA molecules are highly structured in solution and can be used to identify protein ligands. We believe that these molecules can be a future source of high-affinity protein ligands. Here we describe the synthetic method combining the power of both split-and-pool and sub-monomer strategies to synthesize a sample one-bead one-compound (OBOC) library of PTAs.

Peptide tertiary amides (PTAs) are a superfamily of peptidomimetics that include but are not limited to peptides, peptoids and N-methylated peptides. Here we describe a synthetic method which combines&#160;both split-and-pool and sub-monomer strategies to synthesize a one-bead one-compound library of PTAs.

Peptidomimetics are great sources of protein ligands. The oligomeric nature of these compounds enables us to access large synthetic libraries on solid ...

Synthesis and Characterization of Functionalized Metal-organic Frameworks

Metal-organic frameworks have attracted extraordinary amounts of research attention, as they are attractive candidates for numerous industrial and technological applications. Their signature property is their ultrahigh porosity, which however imparts a series of challenges when it comes to both constructing them and working with them. Securing desired MOF chemical and physical functionality by linker/node assembly into a highly porous framework of choice can pose difficulties, as less porous and more thermodynamically stable congeners (e.g., other crystalline polymorphs, catenated analogues) are often preferentially obtained by conventional synthesis methods. Once the desired product is obtained, its characterization often requires specialized techniques that address complications potentially arising from, for example, guest-molecule loss or preferential orientation of microcrystallites. Finally, accessing the large voids inside the MOFs for use in applications that involve gases can be problematic, as frameworks may be subject to collapse during removal of solvent molecules (remnants of solvothermal synthesis). In this paper, we describe synthesis and characterization methods routinely utilized in our lab either to solve or circumvent these issues. The methods include solvent-assisted linker exchange, powder X-ray diffraction in capillaries, and materials activation (cavity evacuation) by supercritical CO2 drying. Finally, we provide a protocol for determining a suitable pressure region for applying the Brunauer-Emmett-Teller analysis to nitrogen isotherms, so as to estimate surface area of MOFs with good accuracy.

Synthesis, activation, and characterization of intentionally designed metal-organic framework materials is challenging, especially when building blocks are incompatible or unwanted polymorphs are thermodynamically favored over desired forms. We describe how applications of solvent-assisted linker exchange, powder X-ray diffraction in capillaries and activation via supercritical CO2 drying, can address some of these challenges.

Metal-organic frameworks have attracted extraordinary amounts of research attention, as they are attractive candidates for numerous industrial and ...

Preparation and Characterization of SDF-1&#945;-Chitosan-Dextran Sulfate Nanoparticles

Chitosan (CS) and dextran sulfate (DS) are charged polysaccharides (glycans), which form polyelectrolyte complex-based nanoparticles when mixed under appropriate conditions. The glycan nanoparticles are useful carriers for protein factors, which facilitate the in vivo delivery of the proteins and sustain their retention in the targeted tissue. The glycan polyelectrolyte complexes are also ideal for protein delivery, as the incorporation is carried out in aqueous solution, which reduces the likelihood of inactivation of the proteins. Proteins with a heparin-binding site adhere to dextran sulfate readily, and are, in turn, stabilized by the binding. These particles are also less inflammatory and toxic when delivered in vivo. In the protocol described below, SDF-1&#945; (Stromal cell-derived factor-1&#945;), a stem cell homing factor, is first mixed and incubated with dextran sulfate. Chitosan is added to the mixture to form polyelectrolyte complexes, followed by zinc sulfate to stabilize the complexes with zinc bridges. The resultant SDF-1&#945;-DS-CS particles are measured for size (diameter) and surface charge (zeta potential). The amount of the incorporated SDF-1&#945; is determined, followed by measurements of its in vitro release rate and its chemotactic activity in a particle-bound form.

Preparation and Characterization of SDF-1&amp;#945;-Chitosan-Dextran Sulfate Nanoparticles

The objective of this protocol is to incorporate SDF-1&#945;, a stem cell homing factor, into dextran sulfate-chitosan nanoparticles. The resultant particles are measured for their size and zeta potential, as well as the content, activity, and in vitro release rate of SDF-1&#945; from the nanoparticles.

Chitosan (CS) and dextran sulfate (DS) are charged polysaccharides (glycans), which form polyelectrolyte complex-based nanoparticles when mixed under ...

Synthesis and Characterization of Supramolecular Colloids

Control over colloidal assembly is of utmost importance for the development of functional colloidal materials with tailored structural and mechanical properties for applications in photonics, drug delivery and coating technology. Here we present a new family of colloidal building blocks, coined supramolecular colloids, whose self-assembly is controlled through surface-functionalization with a benzene-1,3,5-tricarboxamide (BTA) derived supramolecular moiety. Such BTAs interact via directional, strong, yet reversible hydrogen-bonds with other identical BTAs. Herein, a protocol is presented that describes how to couple these BTAs to colloids and how to quantify the number of coupling sites, which determines the multivalency of the supramolecular colloids. Light scattering measurements show that the refractive index of the colloids is almost matched with that of the solvent, which strongly reduces the van der Waals forces between the colloids. Before photo-activation, the colloids remain well dispersed, as the BTAs are equipped with a photo-labile group that blocks the formation of hydrogen-bonds. Controlled deprotection with UV-light activates the short-range hydrogen-bonds between the BTAs, which triggers the colloidal self-assembly. The evolution from the dispersed state to the clustered state is monitored by confocal microscopy. These results are further quantified by image analysis with simple routines using ImageJ and Matlab. This merger of supramolecular chemistry and colloidal science offers a direct route towards light- and thermo-responsive colloidal assembly encoded in the surface-grafted monolayer.

A protocol for the synthesis and characterization of colloids coated with supramolecular moieties is described. These supramolecular colloids undergo self-assembly upon the activation of the hydrogen-bonds between the surface-anchored molecules by UV-light.

Control over colloidal assembly is of utmost importance for the development of functional colloidal materials with tailored structural and mechanical ...

Facile Synthesis of Worm-like Micelles by Visible Light Mediated Dispersion Polymerization Using Photoredox Catalyst

Presented herein is a protocol for the facile synthesis of worm-like micelles by visible light mediated dispersion polymerization. This approach begins with the synthesis of a hydrophilic poly(oligo(ethylene glycol) methyl ether methacrylate) (POEGMA) homopolymer using reversible addition-fragmentation chain-transfer (RAFT) polymerization. Under mild visible light irradiation (&#955; = 460 nm, 0.7 mW/cm2), this macro-chain transfer agent (macro-CTA) in the presence of a ruthenium based photoredox catalyst, Ru(bpy)3Cl2 can be chain extended with a second monomer to form a well-defined block copolymer in a process known as Photoinduced Electron Transfer RAFT (PET-RAFT). When PET-RAFT is used to chain extend POEGMA with benzyl methacrylate (BzMA) in ethanol (EtOH), polymeric nanoparticles with different morphologies are formed in situ according to a polymerization-induced self-assembly (PISA) mechanism. Self-assembly into nanoparticles presenting POEGMA chains at the corona and poly(benzyl methacrylate) (PBzMA) chains in the core occurs in situ due to the growing insolubility of the PBzMA block in ethanol. Interestingly, the formation of highly pure worm-like micelles can be readily monitored by observing the onset of a highly viscous gel in situ due to nanoparticle entanglements occurring during the polymerization. This process thereby allows for a more reproducible synthesis of worm-like micelles simply by monitoring the solution viscosity during the course of the polymerization. In addition, the light stimulus can be intermittently applied in an ON/OFF manner demonstrating temporal control over the nanoparticle morphology.

This article describes a process for producing polymeric self-assembled nanoparticles using visible light mediated dispersion polymerization. Using low energy visible light to control the polymerization allows for the reproducible formation of self-assembled worm-like micelles at high solids content.

Presented herein is a protocol for the facile synthesis of worm-like micelles by visible light mediated dispersion polymerization. This approach begins ...

Anionic Polymerization of an Amphiphilic Copolymer for Preparation of Block Copolymer Micelles Stabilized by &#960;-&#960; Stacking Interactions

In this study, an amphiphilic copolymer that includes a core-forming block with phenyl groups was synthesized by living anionic polymerization of phenyl glycidyl ether (PheGE) on methoxy-polyethylene glycol (mPEG-b-PPheGE). Characterization of the copolymer revealed a narrow molecular distribution (PDI &#60; 1.03) and confirmed the degree of polymerization of mPEG122-b-(PheGE)15. The critical micelle concentration of the copolymer was evaluated using an established fluorescence method with the aggregation behavior evaluated by dynamic light scattering and transmission electronic microscopy. The potential of the copolymer for use in drug delivery applications was evaluated in a preliminary manner including in vitro biocompatibility, loading and release of the hydrophobic anti-cancer drug doxorubicin (DOX). A stable micelle formulation of DOX was prepared with drug loading levels up to 14% (wt%), drug loading efficiencies &#62; 60% (w/w) and sustained release of drug over 4 days under physiologically relevant conditions (acidic and neutral pH, presence of albumin). The high drug loading level and sustained release is attributed to stabilizing &#960;-&#960; interactions between DOX and the core-forming block of the micelles.

Anionic Polymerization of an Amphiphilic Copolymer for Preparation of Block Copolymer Micelles Stabilized by &amp;#960;-&amp;#960; Stacking Interactions

The key steps of living anionic polymerization of phenyl glycidyl ether (PheGE) on methoxy-polyethylene glycol (mPEG-b-PPheGE) are described. The resulting block copolymer micelles (BCMs) were loaded with doxorubicin 14% (wt%) and sustained release of drug over 4 days under physiologically relevant conditions was obtained.

In this study, an amphiphilic copolymer that includes a core-forming block with phenyl groups was synthesized by living anionic polymerization of phenyl ...

Synthesis of Cyclic Polymers and Characterization of Their Diffusive Motion in the Melt State at the Single Molecule Level

We demonstrate a method for the synthesis of cyclic polymers and a protocol for characterizing their diffusive motion in a melt state at the single molecule level. An electrostatic self-assembly and covalent fixation (ESA-CF) process is used for the synthesis of the cyclic poly(tetrahydrofuran) (poly(THF)). The diffusive motion of individual cyclic polymer chains in a melt state is visualized using single molecule fluorescence imaging by incorporating a fluorophore unit in the cyclic chains. The diffusive motion of the chains is quantitatively characterized by means of a combination of mean-squared displacement (MSD) analysis and a cumulative distribution function (CDF) analysis. The cyclic polymer exhibits multiple-mode diffusion which is distinct from its linear counterpart. The results demonstrate that the diffusional heterogeneity of polymers that is often hidden behind ensemble averaging can be revealed by the efficient synthesis of the cyclic polymers using the ESA-CF process and the quantitative analysis of the diffusive motion at the single molecule level using the MSD and CDF analyses.

A protocol for the synthesis and characterization of diffusive motion of cyclic polymers at the single molecule level is presented.

We demonstrate a method for the synthesis of cyclic polymers and a protocol for characterizing their diffusive motion in a melt state at the single ...

Synthesis of Plant Phenol-derived Polymeric Dyes for Direct or Mordant-based Hair Dyeing

Effective hair dyeing through in situ incubation of keratin hair with the products of fungal laccase-catalyzed polymerization of plant phenols has been previously demonstrated. However, the dyeing process takes a long time to complete compared to commercial hair-dyeing products. To overcome this bottleneck, pre-synthesized polymeric products of the oxidative reaction of Trametes versicolor laccase on catechin and catechol, either with or without mordant agents (e.g., FeSO4), were here employed to achieve permanent keratin hair dyeing in various colors and shades. The laccase action in acidic sodium acetate buffer led to a deep black coloration after coupling reactions between the plant phenols. The colored dye products were then desalted and concentrated with ultrafiltration. The dyes, with or without mordant agents, caused a significant increase in &#916;E values (i.e., color difference value) in gray human hair within 2.5 hours. In addition, different keratin colors and shades were induced depending upon the mordanting and pH changes. The dyed hair also exhibited a strong resistance to detergent treatments, indicating that our methods can give rise to permanent hair dyeing.&#160;Overall, our work has provided novel insight into developing eco-friendly hair-dyeing methods as alternatives to commercial toxic diamine-based dyes.

Here, we present a protocol to use pre-synthesized polymeric products derived from fungal laccase-catalyzed polymerization of plant phenols, either with or without mordant agents (e.g., FeSO4), to induce detergent-resistant keratin hair dyeing within 2.5 hours.

Effective hair dyeing through in situ incubation of keratin hair with the products of fungal laccase-catalyzed polymerization of plant phenols has been ...

Preparation and In Vitro Characterization of Dendrimer-based Contrast Agents for Magnetic Resonance Imaging

Paramagnetic complexes of gadolinium(III) with acyclic or macrocyclic chelates are the most commonly used contrast agents (CAs) for magnetic resonance imaging (MRI). Their purpose is to enhance the relaxation rate of water protons in tissue, thus increasing the MR image contrast and the specificity of the MRI measurements. Current clinically approved contrast agents are low molecular weight molecules that are rapidly cleared from the body. The use of dendrimers as carriers of paramagnetic chelators can play an important role in the future development of more efficient MRI contrast agents. Specifically, the increase in local concentration of the paramagnetic species results in a higher signal contrast. Furthermore, this CA provides a longer tissue retention time due to its high molecular weight and size. Here, we demonstrate a convenient procedure for the preparation of macromolecular MRI contrast agents based on poly(amidoamine) (PAMAM) dendrimers with monomacrocyclic DOTA-type chelators (DOTA &#8211; 1,4,7,10-tetraazacyclododecane-1,4,7,10-tetraacetate). The chelating unit was appended by exploiting the reactivity of the isothiocyanate (NCS) group towards the amine surface groups of the PAMAM dendrimer to form thiourea bridges. Dendrimeric products were purified and analyzed by means of nuclear magnetic resonance spectroscopy, mass spectrometry, and elemental analysis. Finally, high resolution MR images were recorded and the signal contrasts obtained from the prepared dendrimeric and the commercially available monomeric agents were compared.

Preparation and In Vitro Characterization of Dendrimer-based Contrast Agents for Magnetic Resonance Imaging

This protocol describes the preparation and characterization of a dendrimeric magnetic resonance imaging (MRI) contrast agent that carries cyclen-based macrocyclic chelates coordinating paramagnetic gadolinium ions. In a series of MRI experiments in vitro, this agent produced an amplified MRI signal when compared to the commercially available monomeric analogue.

Paramagnetic complexes of gadolinium(III) with acyclic or macrocyclic chelates are the most commonly used contrast agents (CAs) for magnetic resonance ...

Preparation and Characterization of C60/Graphene Hybrid Nanostructures

Physical thermal deposition in a high vacuum environment is a clean and controllable method for fabricating novel molecular nanostructures on graphene. We present methods for depositing and passively manipulating C60 molecules on rippled graphene that advance the pursuit of realizing applications involving 1D C60/graphene hybrid structures. The techniques applied in this exposition are geared towards high vacuum systems with preparation areas capable of supporting molecular deposition as well as thermal annealing of the samples. We focus on C60 deposition at low pressure using a homemade Knudsen cell connected to a scanning tunneling microscopy (STM) system. The number of molecules deposited is regulated by controlling the temperature of the Knudsen cell and the deposition time. One-dimensional (1D) C60 chain structures with widths of two to three molecules can be prepared via tuning of the experimental conditions. The surface mobility of the C60 molecules increases with annealing temperature allowing them to move within the periodic potential of the rippled graphene. Using this mechanism, it is possible to control the transition of 1D C60 chain structures to a hexagonal close packed quasi-1D stripe structure.

Preparation and Characterization of C60/Graphene Hybrid Nanostructures

Here we present a protocol for the fabrication of C60/graphene hybrid nanostructures by physical thermal evaporation. Particularly, the proper manipulation of deposition and annealing conditions allow the control over the creation of 1D and quasi 1D C60 structures on rippled graphene.

Physical thermal deposition in a high vacuum environment is a clean and controllable method for fabricating novel molecular nanostructures on graphene. We ...