We acknowledge the UCLA Advanced Light Microscopy/Spectroscopy Laboratory and Leica Microsystems Center of Excellence at the California NanoSystems Institute (RRID:SCR_022789) for providing two-photon microscopy. AS was supported by ISF 604-21 from the Israel Science Foundation. JH was supported by R03DE030205 and R01DE030471 from the NIH/NIDCR. AS and JH were also supported by grant 2021007 from the United States-Israel Binational Science Foundation (BSF).

All mice were maintained in pathogen-free animal facilities at the University of California Los Angeles (UCLA) or the Hebrew University of Jerusalem (HUJI). All experiments involving mice were performed according to regulations and protocols approved by the respective Institutional Animal Care and Use Committee (IACUC) (ARC-2019-013; UCLA) or (MD-23-17184-3; HUJI). A general workflow of the experimental steps is shown in Figure 2A. See the Table of Materials for details related to all instruments, reagents, and materials used in this protocol.
1. Preparation of solutions and gels
<ol>
	<li>Dissection medium: Prepare fresh DMEM/F12 with 0.5% glucose and keep it warm at 37 &#176;C until needed in step 2.4. 
	NOTE: We use DMEM/F12 without phenol red to reduce autofluorescence during live imaging.</li>
	<li>1x Culture medium: Prepare fresh medium using 50% DMEM/F12, 50% rat serum, 1x glutamine substitute, 1x MEM Non-Essential Amino Acids, 1% glucose, 0.1 mg/mL L-ascorbic acid, and 0.5% penicillin-streptomycin. Keep it warm at 37 &#176;C until needed in step 5.5. This medium is used for culturing incisor explants during live imaging. 
	NOTE: The rat serum should be of high quality and specially prepared for whole tissue culturing by researchers or from a commercial source. In particular, the blood must be centrifuged (for 5 min at 1,200 &#215; g at room temperature) before clotting begins to form. After centrifugation, the resulting fibrin clot should be squeezed and discarded33.</li>
	<li>Culture gel: The purpose of the gel is to immobilize samples during imaging and is prepared fresh.
	<ol>
		<li>Make 2% gel in DMEM/F12 by dissolving 200 mg of low melting point agarose in 10 mL of DMEM/F12 using a microwave. Keep the 2% gel at 37 &#176;C.</li>
		<li>Make 2x culture medium (without DMEM/F12) by mixing 50% rat serum, 1x glutamine substitute, 1x MEM Non-Essential Amino Acids, 1% glucose, 0.1 mg/mL L-ascorbic acid, and 0.5% penicillin-streptomycin. Warm the 2x culture medium (without DMEM/F12) to 37 &#176;C.</li>
		<li>Make 1% culture gel by mixing equal volumes of 2% gel and 2x culture medium (without DMEM/F12). Keep the 1% culture gel at 37 &#176;C until needed in step 5.1. 
		NOTE: Make sure all solutions are warm before mixing to avoid gelling. We found 1% gel to be suitable for culturing the adult mouse incisor. Gel percentage should be empirically determined if other tissues are to be cultured.</li>
	</ol>
	</li>
</ol>
2. Extraction of the adult mouse mandibles
<ol>
	<li>Euthanize mice at the desired age using standard procedures approved by the IACUC. 
	NOTE: Here we use CO2&#160;asphyxiation followed by cervical dislocation. Regulations for animal euthanasia may vary in different regions. Researchers should obtain necessary institutional approval prior to performing experiments and ensure compliance with local animal care regulations.</li>
	<li>Disinfect the mouse using 70% ethanol.</li>
	<li>Decapitate the mouse and extract the left and right mandibles.
	<ol>
		<li>Lay the mouse on its belly, then use a #9 single-edge industrial razor blade to cut at the neck region and separate the mouse head from the rest of the body. 
		NOTE: If tissues from the pharynx or the neck region are to be collected as well, decapitation should not be performed, and one can directly proceed to step 2.3.2.</li>
		<li>Turn the mouse over so its ventral side is facing up and the mandibles are easily accessible.</li>
		<li>Secure the animal&#39;s head by holding it gently between the thumb and the index finger.</li>
		<li>Use the razor blade to make a mid-sagittal incision that cuts over the skin of the lower jaw from the lower lip toward the neckline. 
		NOTE: A #15 surgical blade can also be used to make the incision and subsequent dissections (steps 2.3.6-2.3.9).</li>
		<li>As the incision is made, spread open the cut skin using the thumb and the index finger to expose the muscles and jawbone underneath.</li>
		<li>Use the razor blade to sever the masseter muscles on the buccal side of the lower jaw, such that the outside of the left and right hemimandibles are now free from muscle attachments.</li>
		<li>Sever the mylohyoid muscles along the inner side of the mandible to remove muscle attachments there.</li>
		<li>Make another incision at the mandibular symphysis that connects the two hemimandibles. Once cut, the mandible will be separated into the left and right halves.</li>
		<li>Wedge the razor blade between the mandibular condyle and the temporal mandibular joint and carefully dissect out the hemimandible from the rest of the head. 
		NOTE: We found it helpful to simultaneously pull gently on the incisor while cutting. Care should be taken to avoid breaking the mandible and damaging the soft tissues within.</li>
	</ol>
	</li>
	<li>Immediately transfer dissected mandibles to a Petri dish with the prewarmed dissection media (step 1.1) and remove the remaining muscle tissues using a #15 surgical blade. 
	NOTE: Keeping samples in cold media slows down cell activities, resulting in delayed or even failed recoveries of certain cell activities, such as proliferation or cell movement, during live imaging.</li>
</ol>
3. Isolation of the whole mouse incisors
NOTE: Further isolation of the incisor is done under a bright field dissection microscope.
<ol>
	<li>Visually identify the oval region of the mandible that covers the incisor socket and houses the apical portion of the incisor.</li>
	<li>Position the mandible so the inner (lingual) surface is facing upwards.</li>
	<li>While holding the mandible in place with a pair of serrated forceps, generate a window at the oval region by shaving off the overlying membrane bone using a #15 surgical blade, in a direction that is from the condyle towards the molars. This exposes the soft tissue of the apical incisor on the inner surface.</li>
	<li>Turn over the mandible so the outer (buccal) surface is facing upwards.</li>
	<li>Generate a window at the oval region on the outer mandible as described in step 3.3&#160;and use the tip of the scalpel to pick away any remaining bone fragments at the edge. Ensure that the apical end of the tooth is visible from both sides. 
	NOTE: Avoid excessive pressure while shaving the bones to prevent damage to the underlying soft tissue.</li>
	<li>Systematically cut away the bones surrounding the incisor to isolate the entire tooth.
	<ol>
		<li>Make a clean cut at a plane that is immediately adjacent to the apical incisor to first remove the condylar process. 
		NOTE: Be careful not to cut into the incisor.</li>
		<li>Make a second cut just posterior to the 3rd molar, but dorsal to the incisor without damaging the tooth. This removes the bone that includes the coronoid process.</li>
		<li>Serially cut from the tip of the angular process towards the incisor to gradually remove the ventral mandible in a stepwise manner. 
		NOTE: The dental epithelium and associated periodontal tissues are often stuck to the bone and easily ripped off if a large portion of the ventral bone is cut at once. To separate the bone from the incisor soft tissue, one can insert the scalpel (or a pair of sharp non-serrated forceps) between the two tissues at the apical end of the incisor and delicately slide the instrument forward.</li>
		<li>Cut away the alveolar bone with molars and any remaining bones that are still attached to the incisor.</li>
		<li>The entire incisor is now isolated. Transfer the fully dissected incisor to a dish with clean warm dissection media (step 1.1).</li>
	</ol>
	</li>
	<li>Repeat steps 3.2-3.6&#160;to isolate additional incisors as required. 
	NOTE: The maxillary/upper incisors of the mouse also maintain adult stem cells and can be used to study tooth regeneration34. Dental researchers typically focus on the lower incisors because they are more accessible and can be more easily dissected than the upper incisors. Differences between mandibular and maxillary incisor progenitor cells remain to be determined.</li>
</ol>
4.&#160;Removal of periodontal tissues to expose the incisor epithelial cervical loop
<ol>
	<li>With the whole incisor lying down on its lingual side and while holding the tooth in place with a pair of serrated forceps, use a pair of #5 fine forceps to start tucking on the periodontal tissues covering the apical incisor and the cervical loop region.</li>
	<li>Carefully peel off the periodontal tissue from the apical bud, such that the lateral side of the cervical loop (or other regions of interest) becomes visible under the scope. 
	NOTE: Care should be taken to avoid damaging the dental epithelium or detaching it from the mesenchyme. If the incisor has fluorescence signals in the region of interest, and a fluorescent dissection microscope is available, fluorescence signals can be used to help distinguish between tissue types and aid dissections. It is important to efficiently carry out sections 2-4 so samples can be quickly transferred into the culture media and adequately maintained through explant culturing (see below).</li>
</ol>
5. Tissue embedding for explant culture
<ol>
	<li>Add 500 &#181;L of warm, unsolidified culture gel to a well in a 24-well plate and quickly transfer the dissected whole incisors to the well. Swirl the plate a few times to rinse the incisors.</li>
	<li>Add 400 &#181;L of warm, unsolidified culture gel to a culture dish and transfer the rinsed incisors to the dish. 
	NOTE: We use a commercially available culture dish that is compatible with the perfusion setup. See step 6.4 for alternative options.</li>
	<li>Orient the incisor to position the cervical loop region (or other regions of interest) at the center of the dish (Figure 2A,B) and adjust the tilt of the apical incisor for the desired imaging plane. 
	NOTE: Tissue orientation should be done quickly before complete gelation.</li>
	<li>After the gel is set, use a pair of fine forceps to remove any gel on top of the region of interest so it is not covered by gel.</li>
	<li>Add a sufficient volume of warm culture media by slowly pipetting it against the edge of the dish to just cover the sample (~150 &#181;L).</li>
	<li>Move the explant culture to a 37 &#176;C cell culture incubator to allow tissue settling and adjustment to the culture condition for 1 h.</li>
</ol>
6. Timelapse microscopy of incisor explants
NOTE: In this experiment, we used an upright microscope equipped with a 25x water-dipping objective that has a numerical aperture of 1. In general, a water dipping lens with a high numerical aperture is best suited for deep tissue imaging.
<ol>
	<li>Turn on the microscope and the two-photon laser.</li>
	<li>Secure the culture dish to the stage adapter and mount the perfusion adapter ring on top (Figure 2C).</li>
	<li>Connect the stage adapter to a temperature controller set to maintain the culture at 37 &#176;C.</li>
	<li>Connect the inlet and the outlet of the adapter ring to a micro-perfusion pump and begin perfusion of the culture medium, with the perfusion speed set at 20 on the pump. This generates a slow flow (~5 mL/h) of the culture medium over the top of the samples (Figure 2C). 
	NOTE: See the Table of Materials for details about the system to maintain the tissue in a stably controlled environment. Other systems can be used as well. A combination of a 37 &#176;C heating plate and a homemade perfusion culture dish (Supplemental Figure S1) with an inlet and an outlet connected to syringe pumps can also be used.</li>
	<li>Place an Atmospheric Control Barrier Ring (ACBR) on top of the adapter ring and lower the objective through the ACBR to just make contact with the culture medium (Figure 2D).</li>
	<li>Tune the laser wavelength to 920 nm to visualize both GFP and red fluorescence (e.g., tdTomato) signals.</li>
	<li>Locate samples through eyepieces and then on the microscope&#39;s software.</li>
	<li>Set up Z-stacks, multi-position imaging, and time intervals using the software. To follow this protocol, use a z-step size of 4 &#956;m and a time interval of 5 min for 14 h. 
	NOTE: We found that a time interval of longer than 5 min is often insufficient to capture smooth cell movements and divisions.</li>
	<li>Initiate the timelapse imaging. 
	NOTE: Sample position may shift during the first hour and further adjustments may be required.</li>
	<li>Save files for downstream data processing and analyses.</li>
</ol>

Live Tracking of Dental Cells via Two-Photon Microscopy

The authors have no conflicts of interest to disclose.

Live tissue imaging is an important technique that allows us to study the dynamic processes and behaviors of cells when they are maintained in their niche environment41. Ideally, live imaging is performed in vivo with high spatiotemporal resolution. However, in vivo imaging for mammalian organs can be challenging due to tissue inaccessibility, optical opaqueness, and difficulty in immobilizing the animal or the organ for a prolonged period42. Tissue explan...

Over the past two decades, the mouse incisor has emerged as an invaluable platform for investigating the principles of adult stem cell regulation and tooth regeneration1,2. The mouse incisor grows continuously and renews itself throughout the animal&#39;s life. It does so by maintaining both epithelial and mesenchymal stem cells, which can self-renew and differentiate into different cell types of the tooth1,2. While dental epithelial stem cells give rise to ameloblasts, which secrete the enamel matrix, dental mesenchymal stem cells give rise to odontoblasts, cementoblasts, and fibroblasts, which form dentin, cementum, and periodontal ligament, respectively3,4,5,6. This constant supply of new cells maintains tissue homeostasis and allows the replacement of old cells that are lost due to masticatory wear or injuries7,8. Elucidating the cellular and molecular mechanisms that regulate the maintenance and differentiation of dental stem cells is therefore central to understanding dental regeneration, an area of growing interest.
Anatomically, a large portion of the adult mouse incisor is encased in the jawbone. While the incisal edge of the tooth is exposed, the apical end of the incisor fits within a socket and is firmly attached to the surrounding bone through periodontal ligaments and connective tissues (Figure 1A,B). The incisor&#39;s apical end is also the growth region of the tooth and maintains dental stem and progenitor cells in both the epithelial layer and the mesenchymal pulp9,10,11,12,13. Specifically, dental epithelial stem cells are maintained at the bulbous end of the epithelium, known as the apical bud, also referred to as the labial cervical loop (Figure 1C). Similar to the intestinal epithelium and the epidermis, epithelial renewal in the incisor is primarily supported by actively cycling stem cells and their highly proliferative intermediate descendants, called transit-amplifying cells14,15,16,17, both residing in the inner part of the cervical loop. However, whether the incisor epithelium contains and utilizes quiescent stem cells during regeneration remains to be determined. In contrast, both active and quiescent dental mesenchymal stem cells have been identified in the apical pulp, and the quiescent stem cells function as a reserve population that becomes activated during injury repair13,18.
Many of the discoveries on the biology of the mouse incisor renewal and regeneration have resulted from histological investigations, in which samples are obtained at distinct temporal junctures, fixed, processed, and then sectioned into micron-thin slices along a particular plane. Through detailed analysis of histological sections from different mouse models that enable lineage tracing or genetic perturbations, scientists have identified the cell lineages of different progenitor populations, as well as the genetic and signaling pathways that control incisor homeostasis and injury repair19,20,21. However, the static two-dimensional (2D) images of non-vital cells in sections cannot capture the full spectrum of cellular behaviors and spatial organizations in living tissue, such as cell shape changes, movements, and cellular kinetics. Detecting and measuring these rapid cellular changes, which occur at a timescale that is unresolvable through tissue sectioning, require a different strategy. Moreover, acquiring such information is also critical for understanding how dental cells interact with each other, react to different signaling stimuli, and self-organize to maintain tissue structures and functions.
The advent of four-dimensional (4D) deep tissue imaging using two-photon microscopy22, a technology that integrates three spatial dimensions with temporal resolution, overcomes the inherent limitations of histological analysis by enabling spatiotemporal examination of cultured tissue explants, organoids, or even tissues in situ23,24,25,26. For instance, 4D live imaging of the developing tooth epithelium has unveiled the spatiotemporal patterns of cell divisions and migrations that coordinate tissue growth, signaling center formation, and dental epithelial morphogenesis27,28,29,30,31,32. In the adult mouse incisor, 4D imaging has been recently adapted to study cellular behaviors during dental epithelial injury repair. Live imaging revealed that stratum intermedium cells in the suprabasal layer can be directly converted into ameloblasts in the basal layer to regenerate the damaged epithelium, challenging the traditional paradigm of epithelial injury repair15.
Here, we describe the dissection, culturing, and imaging of the adult mouse incisor, focusing on epithelial cells in the labial cervical loop (Figure 1). This technique preserves dental cell vitality for more than 12 h and permits live tracking of fluorescently labeled cells at single-cell resolution. This approach allows investigation of cell motion and migration as well as dynamic changes in cell shape and division orientation under normal culture conditions, or in responses to genetic, physical, and chemical perturbations.

<table border="1" fo:keep-together.within-page="1" fo:keep-with-next.within-page="always">
	<tbody>
		<tr>
			<td>24 well, flat bottom tissue culture plate</td>
			<td>Olympus plastics</td>
			<td>25-107</td>
			<td></td>
		</tr>
		<tr>
			<td>25x HC IRAPO motCORR water dipping objective</td>
			<td>Leica</td>
			<td>11507704</td>
			<td></td>
		</tr>
		<tr>
			<td>Ascorbic acid (Vitamin C)</td>
			<td>Acros Organics</td>
			<td>352685000</td>
			<td></td>
		</tr>
		<tr>
			<td>D-(+)-Glucose bioxtra&#160;</td>
			<td>Sigma Aldrich</td>
			<td>G7528</td>
			<td></td>
		</tr>
		<tr>
			<td>Delta T system&#160;</td>
			<td>Bioptechs</td>
			<td>0420-4</td>
			<td>Including temperature control, culture dishes, and perfusion setup</td>
		</tr>
		<tr>
			<td>Dissection microscope- LEICA S9E</td>
			<td>Leica</td>
			<td>LED300 SLI</td>
			<td></td>
		</tr>
		<tr>
			<td>DMEM/F12</td>
			<td>Thermo Scientific</td>
			<td>11039047</td>
			<td>Basal media without phenol red</td>
		</tr>
		<tr>
			<td>Feather surgical blade (#15)</td>
			<td>Feather</td>
			<td>72044-15</td>
			<td></td>
		</tr>
		<tr>
			<td>Fine forceps</td>
			<td>F.S.T</td>
			<td>11252-23</td>
			<td></td>
		</tr>
		<tr>
			<td>Glutamax&#160;</td>
			<td>Thermo Scientific</td>
			<td>35050-061</td>
			<td>Glutamine substitute</td>
		</tr>
		<tr>
			<td>Leica SP8-DIVE equipped with a 25X HC IRAPO motCORR water dipping objective&#160;</td>
			<td>Leica</td>
			<td>n/a</td>
			<td></td>
		</tr>
		<tr>
			<td>low-melting agarose</td>
			<td>NuSieve</td>
			<td>50080</td>
			<td></td>
		</tr>
		<tr>
			<td>non-essential amino acids (100x)</td>
			<td>Thermo Scientific</td>
			<td>11140-050</td>
			<td></td>
		</tr>
		<tr>
			<td>penicillin&#8211;streptomycin</td>
			<td>Thermo Scientific</td>
			<td>15140122</td>
			<td>10,000 U/mL&#160;</td>
		</tr>
		<tr>
			<td>Petri dish</td>
			<td>Gen Clone</td>
			<td>32-107G</td>
			<td>90 mm&#160;</td>
		</tr>
		<tr>
			<td>Rat serum</td>
			<td>Valley Biomedical</td>
			<td>AS3061SC</td>
			<td>Processed for live imaging</td>
		</tr>
		<tr>
			<td>Razor blade #9</td>
			<td>VWR</td>
			<td>55411-050</td>
			<td></td>
		</tr>
		<tr>
			<td>Scalpel handle</td>
			<td>F.S.T</td>
			<td>10003-12</td>
			<td></td>
		</tr>
		<tr>
			<td>Scissors</td>
			<td>F.S.T</td>
			<td>37133</td>
			<td></td>
		</tr>
		<tr>
			<td>serrated forceps</td>
			<td>F.S.T</td>
			<td>11000-13</td>
			<td></td>
		</tr>
		<tr>
			<td>spring scissors</td>
			<td>F.S.T</td>
			<td>91500-09</td>
			<td></td>
		</tr>
	</tbody>
</table>

using ex vivo live imaging to investigate cell divisions and movements during mouse dental renewal

The continuously growing mouse incisor is emerging as a highly tractable model system to investigate the regulation of adult epithelial and mesenchymal stem cells and tooth regeneration. These progenitor populations actively divide, move, and differentiate to maintain tissue homeostasis and regenerate lost cells in a responsive manner. However, traditional analyses using fixed tissue sections could not capture the dynamic processes of cellular movements and interactions, limiting our ability to study their regulations. This paper describes a protocol to maintain whole mouse incisors in an explant culture system and live-track dental epithelial cells using multiphoton timelapse microscopy. This technique adds to our existing toolbox for dental research and allows investigators to acquire spatiotemporal information on cell behaviors and organizations in a living tissue. We anticipate that this methodology will help researchers further explore mechanisms that control the dynamic cellular processes taking place during both dental renewal and regeneration.

Author Spotlight: Understanding Dynamic Cellular Behaviors in Adult Mouse Dental Tissue Renewal and Repairment 

Using Ex Vivo Live Imaging to Investigate Cell Divisions and Movements During Mouse Dental Renewal

To maintain the correct cellular organization during organ renewal, tissue approaching the cells move and dividing specific orientations and patterns. It is therefore important to understand the rules and regulations of these dynamic cellular events. The mouse incisor is an emerging model for adult stem cell research, and many genetic tools are available in the system to study gene functions, and to label cells for lineage tracing.Most studies to date use adult dental samples collected and fixed its specific time points, and this prevents us from examining life cell behavior. In this protocol, we describe a method to track lifestyles in the adult mouse incisor, and this technique will enable future studies that aim to understand how dynamic cell behaviors contribute to the renewal and repairment of dental tissues.

The apical region of the adult mouse incisor is encased within the mandible (Figure 1) and hence, not directly accessible for visualizing and live-tracking the progenitor cells residing within the growth region. Therefore, we have developed a method to extract the whole incisor from the jawbone and maintain it in an explant culture system for two-photon timelapse microscopy (Figure 2). Here we describe representative results that capture the dynamic process of c...

Watch this Scientific Journal Video about Understanding Dynamic Cellular Behaviors in Adult Mouse Dental Tissue Renewal and Repairment at JoVE.com

Ex vivo live imaging is a powerful technique for studying the dynamic processes of cellular movements and interactions in living tissues. Here, we present a protocol that implements two-photon microscopy to live track dental epithelial cells in cultured whole adult mouse incisors.

The continuously growing mouse incisor is emerging as a highly tractable model system to investigate the regulation of adult epithelial and mesenchymal ...

using-ex-vivo-live-imaging-to-investigate-cell-divisions-movements

Research

JoVE Journal

Developmental Biology

1.2K visualizações.  University of California Los Angeles. Para manter a organização celular correta durante a renovação do órgão, o tecido que se aproxima das células se move e divide orientações e padrões específicos. Portanto, é importante entender as regras e regulamentos desses eventos celulares dinâmicos. O incisivo de camundongo é um modelo emergente para pesquisa com células-tronco adultas, e muitas ferramentas genéticas estão disponíveis no sistema para estudar funções gênicas e marcar células para rastreamento de linha...

Vídeo: Autor em destaque: Compreendendo comportamentos celulares dinâmicos na renovação e reparo do tecido dentário de camundongos adultos 

Dissection and Isolation of Mouse Mandibular Incisors and Associated Periodontal Tissues to Expose the Incisor Epithelial Cervical Loop

To begin, turn the euthanized mouse over so its ventral side faces up and the mandibles are easily accessible. Secure the mouse's head gently between the thumb and the index finger. Using a razor blade, starting from the lower lip toward the neckline, make a mid-sagittal incision on the lower jaw skin.During the incision, use the thumb and index finger to open the cut skin, exposing the underneath muscles and jawbone. Next, sever the masseter muscles on the buccal side of the lower jaw. Sever the mylohyoid muscles along the inner side of the mandible and remove muscle attachments.Make another incision at the mandibular synthesis, connecting the two hemi-mandibles, separating them into the left and right halves. Wedge the razor blade between the mandibular condyle and the temporal mandibular joint to carefully dissect out the hemi mandible from the rest of the head. Immediately transfer the dissected mandibles to a Petri dish containing pre-warmed dissection medium.Next, under a brightfield dissection microscope, use a number 15 surgical blade to remove muscle tissues. Identify the oval region of the mandible that covers the incisor socket and houses the apical portion of the incisor. Position the mandibles such that the inner or lingual surface is facing upward.While holding the mandible with a pair of serrated forceps, using a number 15 surgical blade, shave off the overlying membrane bone from the condyle towards the molars to generate a window at the oval. This exposes the soft tissue of the apical incisor on the inner surface. Next, turn the mandible so the outer or buccal surface faces upwards.As demonstrated for the inner mandible, generate a window at the oval region on the outer mandible. Using a pair of forceps, pick away the remaining bone fragments at the edge, ensuring that the apical end of the tooth is visible from both sides. To isolate the entire tooth, make a clean cut at a plane immediately adjacent to the apical incisor to remove the condylar process.Then make a second cut just posterior to the third molar, but dorsal to the incisor, without damaging the tooth, to remove the coronary process. Serially cut from the tip of the angular process towards the incisor to gradually remove the ventral mandible. Next, cut away the alveolar bone with molars and any remaining bones that are still attached to the incisor.Transfer the fully dissected incisor to a dish containing warm dissection media. Turn on the fluorescent microscope and use the fluorescent signal from tissues to guide the removal of periodontium. Position the inner incisor on its lingual side, and using serrated forceps hold the tooth in place.Then using a pair of number five fine forceps, start tugging on the periodontal tissues, covering the apical incisor, and the cervical loop region. Carefully peel off periodontal tissues from the apical bud, such that the lateral side of the cervical loop is visible.

Periodontal Tissue Embedding and Timelapse Microscopy of Mouse Incisor Explant Cultures

To begin, add 500 microliters of warm culture gel to a well in a 24-well plate. Quickly transfer the dissected whole incisors isolated from the mouse to the well. Swirl the plate a few times to rinse the incisors.Add 400 microliters of warm culture gel to a culture dish and to transfer the rinsed incisors to the dish. Orient the incisor to position the cervical loop region at the center of the dish and adjust the tilt of the apical incisor for the desired imaging plane. Once the gel is set, using a pair of fine forceps, remove any gel on top of the region of interest.Add approximately 150 microliters of warm culture media against the edge of the dish to cover the sample. Place the explant culture at 37 degrees Celsius to allow the tissue to settle. After one hour, turn on the microscope and the two-photon laser.Secure the culture dish to the stage adapter and place the profusion adapter ring on top. Connect the stage adapter to a temperature controller to maintain the culture at 37 degrees Celsius. Connect the inlet and the outlet of the adapter ring to a microprofusion pump.Set the profusion speed to 20 and initiate the profusion of the medium over the sample. Place an ACBR on top of the adapter ring and raise the stage so the objective fits through the ACBR to make contact with the culture medium. Turn the laser wavelength to 920 nanometers to visualize GFP.After locating the sample through an eyepiece, visualize it with a microscope software, then set up Z-step size of four micrometers and a time interval of five minutes for 14 hours. Initiate the time-lapse imaging and save the subsequent files for downstream data analysis. In time-lapse microscopy of the K14-Cre;R26-rtTA;tetO-H2B-GFP cervical loop, the H2B-GFP signals were predominantly observed in the trans-amplifying region of the cervical loop, indicating active cell divisions.Further, the condensation and alignment of chromosomes at the metaphase plate in mitotic cells followed by their segregation during anaphase and into two daughter cells was observed. Most cell divisions were perpendicular or at an oblique angle relative to the basement membrane with fewer horizontal divisions parallel to the basement membrane. Cell division events were also apparent in K14-Cre;R26-mT/mG cervical loops where all epithelial cell membranes were labeled green.Mitotic cells were identified by their cell rounding and subsequent cytokinesis. In K14-Cre;R26-mT/mG cervical loops, both horizontal and vertical cell divisions were also observed.