We would like to thank the Canadian Foundation for Innovation, the British Columbia Knowledge Development Fund and the National Sciences and Engineering Research Council (NSERC) of Canada for supporting ongoing studies on low oxygen regions of coastal and open ocean waters. D.A.W. was supported by fellowships from NSERC, Killam and the TULA foundation funded Centre for Microbial Diversity and Evolution.

<ol>
<li>Set up of filtration apparatus<ol>
<li>Before filtering, first wipe away any condensation from the full bottles and weigh them </li>
<li>Place an autoclave bin on one side of the pump, and the waste flask on the other.</li>
<li>Then place a full sample bottle in the autoclave bin; however, do not remove the cap of the bottle yet.</li>
<li>Pass the tubing through the peristaltic pump so that the luer end of the tubing is in the flask. </li>
<li>Using tweezers, remove the cotton from a sterile 25 ml pipette, and attach the pipette to the other end of the tubing.</li>
</ol></li>
<li>Filtration of seawater <ol>
<li>To begin filtering seawater, open the bottle and insert the pipette. Turn on the pump and set the flow speed to 1. Watch to ensure that water is being pumped in the proper direction. </li>
<li>Allow ~100 ml of water to pass through the entire tubing. </li>
<li>Turn off the pump and attach a Sterivex filter to the male luer fitting at the free end of the tubing. </li>
<li>Continue filtering until no water is left in the bottles.</li>
</ol></li>
<li>Storage of filters<ol>
<li>To store the filters, first expel any remaining water with a 30-60 ml syringe.</li>
<li>Seal the bottom of the Sterivex filter with Parafilm. Using a pipette, add 1.8ml lysis buffer to the filter, keeping ~ 200 ul of space in the filter for later addition of reagents.</li>
<li>Then, seal the top of the Sterivex filter with a small piece of Parafilm, and label the filters with the date and sample identification.</li>
<li>Store the filters in pre-labelled 50 ml falcon tubes at -80&deg;C</li>
</ol></li>
<li>Clean up<ol>
<li>Insert the 25 ml pipette into a flask containing 0.1% HCl, and switch on the pump.</li>
<li>After the HCl wash, rinse the tubing with autoclaved water. Finally, measure and record the mass of the now empty 1L bottles in order to calculate the volume of water passed through the filter. </li>
</ol></li>
</ol>
Representative Results: Each 1 L water sample yields one Sterivix filter, which contains biomass greater than 0.22 &micro;m. This is stored in lysis buffer for subsequent DNA extraction and analysis. The final result consists of one Sterivix filter per 1-liter bottle stored in lysis buffer and ready for DNA extraction. The filter contains biomass greater than 0.22 &micro;m. Filters can be stored at -80&deg;C prior to eDNA extraction.

The authors have nothing to disclose.

It is imperative to wipe down benches and pumps with a damp towel after use to remove any lingering traces of salt water that would otherwise corrode equipment. Although the procedure is simple, the time requirement can be extensive depending on the concentration of biomass or debris in the sample being filtered.

<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="http://www.w3.org/1999/xhtml" xml:lang="en" lang="en">	
		
		<div>
		<table border="1">
		<thead>
		<tr>
		<th>Material Name</th>
		<th>Type</th>
		<th>Company</th>
		<th>Catalogue Number</th>
		<th>Comment</th>
		</tr>
		</thead>
		<tbody>
		
<tr>
<td>Peristaltic pump</td>
<td>&nbsp;</td>
<td>Masterflex (Cole Palmer)</td>
<td>77913-20, 77200-62, 77200-04</td>
<td>&nbsp;</td>
<tr>
<td>Tygon LFL tubing</td>
<td>&nbsp;</td>
<td>Masterflex (Cole Palmer)</td>
<td>06429-24</td>
<td>For filtration apparatus</td>
</tr>
<tr>
<td>Hose clamps</td>
<td>&nbsp;</td>
<td>Cole Palmer</td>
<td>0683204</td>
<td>For filtration apparatus</td>
</tr>
<tr>
<td>1/4&#x201D; x 3/16&#x201D; pipe adaptors</td>
<td>&nbsp;</td>
<td>Cole Palmer</td>
<td>31702-20</td>
<td>For filtration apparatus</td>
</tr>
<tr>
<td>Polypropylene prefilter housing</td>
<td>&nbsp;</td>
<td>ADVANTEC</td>
<td>501200</td>
<td>For filtration apparatus</td>
</tr>
<tr>
<td>Metal luer fitting (Hose end to Male luer lock)</td>
<td>&nbsp;</td>
<td>Cole Palmer</td>
<td>31507-27</td>
<td>For filtration apparatus</td>
</tr>
<tr>
<td>2&#x201C; Magnets</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>For filtration apparatus</td>
</tr>
<tr>
<td>3 port carboy caps</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>For filtration apparatus</td>
</tr>
<tr>
<td>GV 0.22 &mu;m STERIVIX filters</td>
<td>&nbsp;</td>
<td>Millipore</td>
<td>SVGV01R5</td>
<td>&nbsp;</td>
<tr>
<td>47 mm diameter 2.7 &mu;m GF/D filters</td>
<td>&nbsp;</td>
<td>Whatman</td>
<td>1823047</td>
<td>&nbsp;</td>
<tr>
<td>Lysis buffer</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>0.75 M sucrose, 40 mM EDTA, 50 mM Tris (pH 8.3)</td>
</tr>
<tr>
<td>0.1 % HCl</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>For post-filtration rinse</td>
</tr>
<tr>
<td>Autoclaved water</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>For post-filtration rinse</td>
</tr>		</tbody>
		</table>
		</div>

small volume (1-3l) filtration of coastal seawater samples

The workflow begins with the collection of coastal marine waters for downstream microbial community, nutrient and trace gas analyses. For today s demonstration samples were collected from the deck of the HMS John Strickland operating in Saanich Inlet. This video documents small volume (~1 L) filtration of microbial biomass from the water column. The protocol is an extension of the large volume sampling protocol described earlier, with one major difference: here, there is no pre-filtration step, so all size classes of biomass are collected down to the 0.22 &mu;m filter cut-off. Samples collected this way are ideal for nucleic acid analysis. The set-up, filtration, and clean-up steps each take about 20-30 minutes. If using two peristaltic pumps simultaneously, up to 8 samples may be filtered at the same time. To prevent biofilm formation between sampling trips, all filtration equipment must be rinsed with dilute HCl and deionized water and autoclaved immediately after use.

Watch this Scientific Journal Video about Small Volume 1-3L Filtration of Coastal Seawater Samples at JoVE.com

Small Volume 1-3L Filtration of Coastal Seawater Samples

This video documents small volume (~1 L) filtration of microbial biomass from the water column.

Small Volume (1-3L) Filtration of Coastal Seawater Samples

The workflow begins with the collection of coastal marine waters for downstream microbial community, nutrient and trace gas analyses. For today s ...

small-volume-1-3l-filtration-of-coastal-seawater-samples

Research

Education

JoVE Core

JoVE Journal

Analytical Chemistry

Biology

Unit 1

Introduction to Separation Methods

SCIENTISTS IN ACTION

11.1K Views.  University of British Columbia - UBC. Это видео документов небольшого объема (~ 1 л) фильтрации микробной биомассы из толщи воды.

Video: Small Volume 1-3L Filtration of Coastal Seawater Samples

Seawater Sampling and Collection

This video documents methods for collecting coastal marine water samples and processing them for various downstream applications including biomass concentration, nucleic acid purification, cell abundance, nutrient and trace gas analyses. For today's demonstration samples were collected from the deck of the HMS John Strickland operating in Saanich Inlet. An A-frame derrick, with a multi-purpose winch and cable system, is used in combination with Niskin or Go-Flo water sampling bottles. Conductivity, Temperature, and Depth (CTD) sensors are also used to sample the underlying water mass. To minimize outgassing, trace gas samples are collected first.  Then, nutrients, water chemistry, and cell counts are determined. Finally, waters are collected for biomass filtration. The set-up and collection time for a single cast is ~1.5 hours at a maximum depth of 215 meters. Therefore, a total of 6 hours is generally needed to complete the collection series described here.

This video documents methods for collecting coastal marine water samples and processing them for various downstream applications including biomass concentration, nucleic acid purification, cell abundance, nutrient and trace gas analyses.

This video documents methods for collecting coastal marine water samples and processing them for various downstream applications including biomass ...

Large Volume (20L+) Filtration of Coastal Seawater Samples

The workflow begins with the collection of coastal marine waters for downstream microbial community, nutrient and trace gas analyses. For this method, samples were collected from the deck of the HMS John Strickland operating in Saanich Inlet. This video documents large volume (&ge;20 L) filtration of microbial biomass, ranging between 0.22&mu;m and 2.7&mu;m in diameter, from the water column. Two 20L samples can be filtered simultaneously using a single pump unit equipped with four rotating heads. Filtration is done in the field on extended trips, or immediately upon return for day trips. It is important to record the amount of water passing through each sterivex filter unit. To prevent biofilm formation between sampling trips, all filtration equipment must be rinsed with dilute HCl and deionized water and autoclaved immediately after use. This procedure will take approximately 5 hours plus an additional hour for clean up.

Large Volume 20L+ Filtration of Coastal Seawater Samples

This video documents large volume (&ge;20 L) filtration of microbial biomass, ranging between 0.22&mu;m and 2.7&mu;m in diameter, from the water column.

The workflow begins with the collection of coastal marine waters for downstream microbial community, nutrient and trace gas analyses. For this method, ...

Substrate Generation for Endonucleases of CRISPR/Cas Systems

The interaction of viruses and their prokaryotic hosts shaped the evolution of bacterial and archaeal life. Prokaryotes developed several strategies to evade viral attacks that include restriction modification, abortive infection and CRISPR/Cas systems. These adaptive immune systems found in many Bacteria and most Archaea consist of clustered regularly interspaced short palindromic repeat (CRISPR) sequences and a number of CRISPR associated (Cas) genes (Fig. 1) 1-3. Different sets of Cas proteins and repeats define at least three major divergent types of CRISPR/Cas systems 4. The universal proteins Cas1 and Cas2 are proposed to be involved in the uptake of viral DNA that will generate a new spacer element between two repeats at the 5' terminus of an extending CRISPR cluster 5. The entire cluster is transcribed into a precursor-crRNA containing all spacer and repeat sequences and is subsequently processed by an enzyme of the diverse Cas6 family into smaller crRNAs 6-8. These crRNAs consist of the spacer sequence flanked by a 5' terminal (8 nucleotides) and a 3' terminal tag derived from the repeat sequence 9. A repeated infection of the virus can now be blocked as the new crRNA will be directed by a Cas protein complex (Cascade) to the viral DNA and identify it as such via base complementarity10. Finally, for CRISPR/Cas type 1 systems, the nuclease Cas3 will destroy the detected invader DNA 11,12 .
These processes define CRISPR/Cas as an adaptive immune system of prokaryotes and opened a fascinating research field for the study of the involved Cas proteins. The function of many Cas proteins is still elusive and the causes for the apparent diversity of the CRISPR/Cas systems remain to be illuminated. Potential activities of most Cas proteins were predicted via detailed computational analyses. A major fraction of Cas proteins are either shown or proposed to function as endonucleases 4.
Here, we present methods to generate crRNAs and precursor-cRNAs for the study of Cas endoribonucleases. Different endonuclease assays require either short repeat sequences that can directly be synthesized as RNA oligonucleotides or longer crRNA and pre-crRNA sequences that are generated via in vitro T7 RNA polymerase run-off transcription. This methodology allows the incorporation of radioactive nucleotides for the generation of internally labeled endonuclease substrates and the creation of synthetic or mutant crRNAs. Cas6 endonuclease activity is utilized to mature pre-crRNAs into crRNAs with 5'-hydroxyl and a 2',3'-cyclic phosphate termini.

CRISPR/Cas systems mediate adaptive immunity in Bacteria and Archaea. Many Cas proteins are proposed to act as endoribonucleases acting on crRNA precursors of varying length. Here we illustrate three different approaches to generate pre-crRNA substrates for the biochemical analysis of Cas endonuclease activity.

The  interaction of viruses and their prokaryotic hosts shaped the evolution of  bacterial and archaeal life. Prokaryotes developed several strategies to ...

A High-throughput Method for Measurement of Glomerular Filtration Rate in Conscious Mice

The measurement of glomerular filtration rate (GFR) is the gold standard in kidney function assessment. Currently, investigators determine GFR by measuring the level of the endogenous biomarker creatinine or exogenously applied radioactive labeled inulin (3H or 14C). Creatinine has the substantial drawback that proximal tubular secretion accounts for ~50% of total renal creatinine excretion and therefore creatinine is not a reliable GFR marker. Depending on the experiment performed, inulin clearance can be determined by an intravenous single bolus injection or continuous infusion (intravenous or osmotic minipump). Both approaches require the collection of plasma or plasma and urine, respectively. Other drawbacks of radioactive labeled inulin include usage of isotopes, time consuming surgical preparation of the animals, and the requirement of a terminal experiment. Here we describe a method which uses a single bolus injection of fluorescein isothiocyanate-(FITC) labeled inulin and the measurement of its fluorescence in 1-2 &mu;l of diluted plasma. By applying a two-compartment model, with 8 blood collections per mouse, it is possible to measure GFR in up to 24 mice per day using a special work-flow protocol. This method only requires brief isoflurane anesthesia with all the blood samples being collected in a non-restrained and awake mouse. Another advantage is that it is possible to follow mice over a period of several months and treatments (i.e. doing paired experiments with dietary changes or drug applications). We hope that this technique of measuring GFR is useful to other investigators studying mouse kidney function and will replace less accurate methods of estimating kidney function, such as plasma creatinine and blood urea nitrogen.

Measurement of glomerular filtration rate (GFR) is the gold standard for kidney function assessment. Here we describe a high-throughput method which allows the determination of GFR in conscious mice by using a single bolus injection, determination of fluorescein isothiocyanate (FITC)-inulin in plasma and calculation of GFR by a two-phase exponential decay model.

The measurement of  glomerular filtration rate (GFR) is the gold standard in kidney function  assessment. Currently, investigators determine GFR by ...

Rapid Isolation And Purification Of Mitochondria For Transplantation By Tissue Dissociation And Differential Filtration

Previously described mitochondrial isolation methods using differential centrifugation and/or Ficoll gradient centrifugation require 60 to 100 min to complete. We describe a method for the rapid isolation of mitochondria from mammalian biopsies using a commercial tissue dissociator and differential filtration. In this protocol, manual homogenization is replaced with the tissue dissociator&#8217;s standardized homogenization cycle. This allows for uniform and consistent homogenization of tissue that is not easily achieved with manual homogenization. Following tissue dissociation, the homogenate is filtered through nylon mesh filters, which eliminate repetitive centrifugation steps. As a result, mitochondrial isolation can be performed in less than 30 min. This isolation protocol yields approximately 2 x 1010 viable and respiration competent mitochondria from 0.18 &#177; 0.04 g (wet weight) tissue sample.

A method for rapid isolation of mitochondria from mammalian tissue biopsies is described. Rat liver or skeletal muscle preparations were homogenized with a commercial tissue dissociator and mitochondria were isolated by differential filtration through nylon mesh filters. Mitochondrial isolation time is &#60;30 min compared to 60 - 100 min using alternative methods.

Previously described mitochondrial isolation methods using differential centrifugation and/or Ficoll gradient centrifugation require 60 to 100 min to ...

Physiology Lab Demonstration: Glomerular Filtration Rate in a Rat

Measurements of glomerular filtration rate (GFR), and the fractional excretion of sodium (Na) and potassium (K) are critical in assessing renal function in health and disease. GFR is measured as the steady state renal clearance of inulin which is filtered at the glomerulus, but not secreted or reabsorbed along the nephron. The fractional excretion of Na and K can be determined from the concentration of Na and K in plasma and urine. The renal clearance of inulin can be demonstrated in an anesthetized animal which has catheters in the femoral artery, femoral vein and bladder. The equipment and supplies used for this procedure are those commonly available in a research core facility, and thus makes this procedure a practical means for measuring renal function. The purpose of this video is to demonstrate the procedures required to perform a lab demonstration in which renal function is assessed before and after a diuretic drug. The presented technique can be utilized to assess renal function in rat models of renal disease.

The purpose of this protocol is to demonstrate the principles and techniques for measuring and calculating glomerular filtration rate, urine flow rate, and excretion of sodium and potassium in a rat. This demonstration can be used to provide students with an overall conceptual understanding of how to measure renal function.

Measurements of glomerular filtration rate (GFR), and the fractional excretion of sodium (Na) and potassium (K) are critical in assessing renal function ...

Measuring Pressure Volume Loops in the Mouse

Understanding the causes and progression of heart disease presents a significant challenge to the biomedical community. The genetic flexibility of the mouse provides great potential to explore cardiac function at the molecular level. The mouse&#39;s small size does present some challenges in regards to performing detailed cardiac phenotyping. Miniaturization and other advancements in technology have made many methods of cardiac assessment possible in the mouse. Of these, the simultaneous collection of pressure and volume data provides a detailed picture of cardiac function that is not available through any other modality. Here a detailed procedure for the collection of pressure-volume loop data is described. Included is a discussion of the principles underlying the measurements and the potential sources of error. Anesthetic management and surgical approaches are discussed in great detail as they are both critical to obtaining high quality hemodynamic measurements. The principles of hemodynamic protocol development and relevant aspects of data analysis are also addressed.

This manuscript describes a detailed protocol for the collection of pressure-volume data from the mouse.

Understanding the causes and progression of heart disease presents a significant challenge to the biomedical community. The genetic flexibility of the ...

Filtration Isolation of Nucleic Acids:  A Simple and Rapid DNA Extraction Method

FINA, filtration isolation of nucleic acids, is a novel extraction method which utilizes vertical filtration via a separation membrane and absorbent pad to extract cellular DNA from whole blood in less than 2 min. The blood specimen is treated with detergent, mixed briefly and applied by pipet to the separation membrane. The lysate wicks into the blotting pad due to capillary action, capturing the genomic DNA on the surface of the separation membrane. The extracted DNA is retained on the membrane during a simple wash step wherein PCR inhibitors are wicked into the absorbent blotting pad. The membrane containing the entrapped DNA is then added to the PCR reaction without further purification. This simple method does not require laboratory equipment and can be easily implemented with inexpensive laboratory supplies. Here we describe a protocol for highly sensitive detection and quantitation of HIV-1 proviral DNA from 100 &#181;l whole blood as a model for early infant diagnosis of HIV that could readily be adapted to other genetic targets.

We describe here a simple and rapid paper-based DNA extraction method of HIV proviral DNA from whole blood detected by quantitative PCR. This protocol can be extended for use in detecting other genetic markers or using alternative amplification methods.

FINA, filtration isolation of nucleic acids, is a novel extraction method which utilizes vertical filtration via a separation membrane and absorbent pad ...

Volume Segmentation and Analysis of Biological Materials Using SuRVoS (Super-region Volume Segmentation) Workbench

Segmentation is the process of isolating specific regions or objects within an imaged volume, so that further study can be undertaken on these areas of interest. When considering the analysis of complex biological systems, the segmentation of three-dimensional image data is a time consuming and labor intensive step. With the increased availability of many imaging modalities and with automated data collection schemes, this poses an increased challenge for the modern experimental biologist to move from data to knowledge. This publication describes the use of SuRVoS Workbench, a program designed to address these issues by providing methods to semi-automatically segment complex biological volumetric data. Three datasets of differing magnification and imaging modalities are presented here, each highlighting different strategies of segmenting with SuRVoS. Phase contrast X-ray tomography (microCT) of the fruiting body of a plant is used to demonstrate segmentation using model training, cryo electron tomography (cryoET) of human platelets is used to demonstrate segmentation using super- and megavoxels, and cryo soft X-ray tomography (cryoSXT) of a mammalian cell line is used to demonstrate the label splitting tools. Strategies and parameters for each datatype are also presented. By blending a selection of semi-automatic processes into a single interactive tool, SuRVoS provides several benefits. Overall time to segment volumetric data is reduced by a factor of five when compared to manual segmentation, a mainstay in many image processing fields. This is a significant savings when full manual segmentation can take weeks of effort. Additionally, subjectivity is addressed through the use of computationally identified boundaries, and splitting complex collections of objects by their calculated properties rather than on a case-by-case basis.

Volume Segmentation and Analysis of Biological Materials Using SuRVoS Super-region Volume Segmentation Workbench

Segmentation of three-dimensional data from many imaging techniques is a major bottleneck in analysis of complex biological systems. Here, we describe the use of SuRVoS Workbench to semi-automatically segment volumetric data at various length-scales using example datasets from cryo-electron tomography, cryo soft X-ray tomography, and phase contrast X-ray tomography techniques.

Segmentation is the process of isolating specific regions or objects within an imaged volume, so that further study can be undertaken on these areas of ...

Measurement of Endothelium-Dependent Vasorelaxation in the Mouse Thoracic Aorta Using Tensometric Small Volume Chamber Myography

Small volume chamber tensometric myography is a commonly used technique to evaluate the vascular contractility of small and large blood vessels in laboratory animals and small arteries isolated from human tissue. The technique allows researchers to maintain isolated blood vessels in a tightly controlled and standardized (near-physiological) setting, with the option of adjusting to various environmental factors, while challenging the isolated vessels with different pharmacological agents that can induce vasoconstriction or vasodilation. The myograph chamber also provides a platform to measure vascular reactivity in response to various hormones, inhibitors, and agonists that may impact the function of smooth muscle and endothelial layers separately or simultaneously. The blood vessel wall is a complex structure consisting of three different layers: the intima (endothelial layer), media (smooth muscle and elastin fibers), and adventitia (collagen and other connective tissue). To gain a clear understanding of the functional properties of each layer, it is critical to have access to an experimental platform and system that would allow for a combinational approach to study all three layers simultaneously. Such an approach demands access to a semi-physiological condition that would mimic the in vivo environment in an ex vivo setting. Small volume chamber tensometric myography has provided an ideal environment to evaluate the impact of environmental cues, experimental variables, or pharmacological agonists and antagonists on vascular properties. For many years, scientists have used the tensometric myograph technique to measure endothelial function and smooth muscle contractility in response to different agents. In this report, a small volume chamber tensometric myograph system is used to measure endothelial function in the isolated mouse aorta. This report focuses on how small volume chamber tensometric myography can be used to evaluate the functional integrity of the endothelium in small segments of a large artery such as the thoracic aorta.

The present protocol describes the concepts and technical application of the tensometric myograph technique using a multi-chamber myograph system in the experimental ex vivo assessment of mouse aortic endothelial function.