This study was supported in part by the NASA Nebraska Space Grant and National Science Foundation under grant No. 0926880.

1. Preparation of the Latex Vessel
<ol>
	<li>Fix both ends of the latex vessel to barbed hose connections, which are fastened on a sturdy workbench.</li>
	<li>Measure the area of interest on latex vessel to determine the field of view. The area of interest for a stent test should be centered between the barbed hose connectors and include approximately one inch on each side of the stent in order to observe the strains outside the stented area.</li>
	<li>Record the distance from the outside edge of one barbed hose connector to the center location between the connectors, which is also the approximate center of the latex vessel. Translate the distance onto the catheter by measuring from the center of the stent up the catheter. Then mark the catheter with a marker.</li>
	<li>Remove the latex vessel from the barbed hose connectors.</li>
	<li>Prepare the latex vessel by spraying the area of interest with a stochastic pattern of white and black spray paint or marking the area of interest with random dots using permanent marker. For smaller samples and finer stochastic pattern is required.</li>
</ol>
2. In vitro Test System and Calibration of ARAMIS System
<ol>
	<li>Select the calibration panel that is slightly larger than the area of interest measured in step 1.</li>
	<li>Place the calibration panel between the barbed hose connectors at the area of interest and ensure that the area of interest is well lit.</li>
	<li>Adjust the distance between two cameras, the distance from the sample, and the camera height based on the calibration panel selected. Each calibration panel is different; therefore the ARAMIS user manual will have to be consulted to determine these distances.</li>
	<li>Open a new project in ARAMIS by selecting "File", then "New Project". Next click on the "Sensor" tab and select "Calibration", then "Full Calibration".</li>
	<li>The ARAMIS software will now walk the user through the steps to calibrate the cameras.</li>
	<li>With the lens aperture fully open, focus the camera on the calibration panel by loosening the set screw on the camera and rotating the lens. Once focused, retighten the set screw and close the aperture.</li>
	<li>Take the first image of the calibration process. Displace or rotate the calibration panel according to the demonstration on the computer, until the image is focused on the computer screen. Take the second image. Repeat this process for the remainder of the calibration images.</li>
	<li>Once all of the calibration images are taken, the ARAMIS imaging analysis software will calculate the calibration settings. The calibration process should be repeated if the calibration deviation is greater than 0.04. Any adjustments made to the focus of the camera or the distance between cameras will render the calibration process void.</li>
	<li>Remove the calibration panel and place the painted latex vessel back onto the barbed hose connectors.</li>
</ol>
3. Pretest to Avoid Excessive Background Noise
<ol>
	<li>Determine the number of frames per second that is desired for the test. Increased frames per second will produce more uniform strain results.</li>
	<li>Adjust the shutter speed to less than 1 frame per second and so that no red is displayed on the image.</li>
	<li>Take 5 images.</li>
	<li>Add start points on the image series and compute the test.</li>
	<li>While holding "ctrl", click on the center of sample to observe the background noise. If the pretest noise is above 75 microstrain the calibration process must be redone.</li>
</ol>
4. Stent Deployment
<ol>
	<li>Select the amount of images desired to take during the test. 200 images will suffice for the stent expansion.</li>
	<li>Gradually insert the catheter into the latex vessel, and using the marker indicator on the catheter to guide the stent insertion until it reaches the central location.</li>
	<li>Begin taking images with ARAMIS.</li>
	<li>For the balloon-expandable stent, gradually increase the balloon pressure to expand stent until the balloon is fully expanded; then gradually decrease the pressure of balloon to zero and the balloon is deflated and withdrawn along with the catheter.</li>
	<li>For the self -expanding stent, gradually remove the sheath until the stent is fully expanded; then gradually retract the catheter.</li>
</ol>
5. Images Analysis
<ol>
	<li>Strain history of a specific point on the vessel
	<ol>
		<li>Create a stage point by holding the "ctrl" key and clicking on the area of interest.</li>
		<li>Select the type of strain that is desired, i.e. strain in the X, Y, XY, major strain, minor strain, or Mises strain.</li>
		<li>The plot in the lower right corner will display the strain at the point selected over the duration of the test.</li>
	</ol>
	</li>
	<li>Spatial strain along a specific path of the vessel
	<ol>
		<li>Create a multistage point line by clicking on the "sections" tab, then "create section". Select a line on the image parallel to the X axis at Y equals zero. This will create a number of stage points in a line.</li>
		<li>After the multistage line is created the plot in the lower corner will display a series of lines on one plot. Each line represents the strain at one instance in time along the length of the section.</li>
	</ol>
	</li>
	<li>Creating a best fit cylinder to analyze expansion rate and radius of the vessel
	<ol>
		<li>In the upper tool bar select "primitives", then "best fit cylinder".</li>
		<li>Select a small section of the image using the "select through surface" tool on the right tool bar.</li>
		<li>The ARAMIS software will generate a three dimensional best fit cylinder.</li>
		<li>The images can then be cycled through to observe how the diameter of the latex vessel is varying.</li>
	</ol>
	</li>
	<li>Evaluating the distance between two points
	<ol>
		<li>Under the "analysis" tab click on "point to point distance".</li>
		<li>Select a length on the image that is desired for analysis by selecting two points.</li>
		<li>The images can then be cycled through to observe the change in distance between the two points over time.</li>
	</ol>
	</li>
</ol>
6. Representative Results
The stent struts expand the vessel wall outwards, strains will generally be higher around stent location. Figure 1 is an example of strain mapping during the recoil process of balloon-expandable stent, as well as major strain history at one specific point. The black dots in Figure 1 are reference points, which were used by the high-speed cameras to capture and track the displacements of these reference points on the conduit. Based on the recorded movement of reference points, the software will then be used to calculate the strains of the conduit or any other targeted object. Major strain, also referred to as the maximum principal strain, is calculated as follows:
<img alt="Equation 1" src="/files/ftp_upload/3945/3945eq1.jpg" />
It is clear that the implanted stent led to non-uniform strain distribution on the vessel surface. This could be explained by the recoil loading from ends-constrained latex conduit and the mesh structure of stent. This strain field corresponds to the initial stage of stent recoil, as identified by the red cross marker in the bottom image of Figure 1. The major strain-history curve of a specific point 10 demonstrated distinguishable stages of stent implantation. The balloon expansion occurs from approximately 10 to 12 seconds and stent recoil following the deflation of the balloon occurs between 12 and 14 seconds.
<img alt="Figure 1" src="/files/ftp_upload/3945/3945fig1.jpg" /> 
Figure 1. Experimental setup (top); non-uniform strain distribution on the stented conduit surface (middle); the major strain history at the point 10 (bottom).

<ol>
	<li>Fischman, D. L., Leon, M. B., Baim, D. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+randomized+comparison+of+coronary-stent+placement+and+balloon+angioplasty+in+the+treatment+of+coronary+artery+disease.+Stent+Restenosis+Study+Investigators.">A randomized comparison of coronary-stent placement and balloon angioplasty in the treatment of coronary artery disease. Stent Restenosis Study Investigators.</a> N. Engl. J. Med. 331, 496-501 (1994).</li><li>Abul Hasan Muhammad Bashar, T. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Mechanical+Properties+of+Various+Z-Stent+Designs:+An+Endovascular+Stent-Grafting+Perspective.">Mechanical Properties of Various Z-Stent Designs: An Endovascular Stent-Grafting Perspective.</a> Artificial Organs. 27, 714-721 (2003).</li><li>Nuutinen, J. u. h. a. -. P. e. k. k. a. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Mechanical+properties+and+in+vitro+degradation+of+bioabsorbable+self-expanding+braided+stents.">Mechanical properties and in vitro degradation of bioabsorbable self-expanding braided stents.</a> Journal of Biomaterials Science -- Polymer Edition. , 255-266 (2003).</li><li>C. Schulz, R. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Coronary+stent+symmetry+and+vascular+injury+determine+experimental+restenosis.">Coronary stent symmetry and vascular injury determine experimental restenosis.</a> Heart. 83, 462-467 (2000).</li><li>Jiménez, J. M., Davies, P. F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Hemodynamically+Driven+Stent+Strut+Design.">Hemodynamically Driven Stent Strut Design.</a> Annals of Biomedical Engineering. 1483, (2009).</li><li>Johnston, C. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+Mechanical+Properties+of+Endovascular+Stents:+An+In+Vitro+Assessment.">The Mechanical Properties of Endovascular Stents: An In Vitro Assessment.</a> Cardiovascular Engineering: An International Journal. 10, 128-135 (2010).</li><li>Mejia, J. u. a. n. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Evaluation+of+the+effect+of+stent+strut+profile+on+shear+stress+distribution+using+statistical+moments.">Evaluation of the effect of stent strut profile on shear stress distribution using statistical moments.</a> Biomedical Engineering Online. , 1-10 (2009).</li><li>. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> ARAMIS User Manual. , (2009).</li><li>Chesler, N. C., Thompson-Figueroa, J., Millburne, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Measurements+of+Mouse+Pulmonary+Biomechanics.">Measurements of Mouse Pulmonary Biomechanics.</a> Journal of Biomechanical Engineering. 126, 309-314 (2004).</li><li>de Korte, C. L., Sierevogel, M. J., Mastik, F., Strijder, C., Schaar, J. A., Velema, E., Pasterkamp, G., Serruys, P. W., van der Steen, A. F. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Identification+of+Atherosclerotic+Plaque+Components+With+Intravascular+Ultrasound+Elastography+In+Vivo+A+Yucatan+Pig+Study.">Identification of Atherosclerotic Plaque Components With Intravascular Ultrasound Elastography In Vivo A Yucatan Pig Study.</a> Circulation. 105, 1627-1630 (2002).</li></ol>

No conflicts of interest declared.

The stereo optical surface strain measurement system is used to measure the local strains over the deforming surface for both the in- and out-of-plane motions without contacting the specimen. This system uses two high-speed optical cameras to take pictures of a random contrasting pattern putting on the surface to construct accurate measurements of motions of each point, with a high accuracy of resolving surface strains.
It should be noted that the required contrasting pattern need adheres to ...

<table border="1">
	<tbody>
		<tr>
			<td>Equipment Used</td>
			<td>Company</td>
			<td>Catalogue number</td>
			<td>Comments </td>
		</tr>
		<tr>
			<td>ARAMIS Camera System</td>
			<td>GOM: Optical Measuring Techniques</td>
			<td>&nbsp;</td>
			<td>&nbsp;</td>
		</tr>
		<tr>
			<td>PALMAZ Genesis TRANSHEPATIC BILIARY STENT</td>
			<td>Cordis Corporation</td>
			<td>PG5910B</td>
			<td>Balloon-expandable stent</td>
		</tr>
		<tr>
			<td>Z-MED Balloon Dilatation Catheter</td>
			<td>B. Braun Medical Inc.</td>
			<td>PDZ336</td>
			<td>Balloon dilatation catheter</td>
		</tr>
	</tbody>
</table>

monitoring the wall mechanics during stent deployment in a vessel

Clinical trials have reported different restenosis rates for various stent designs1. It is speculated that stent-induced strain concentrations on the arterial wall lead to tissue injury, which initiates restenosis2-7. This hypothesis needs further investigations including better quantifications of non-uniform strain distribution on the artery following stent implantation. A non-contact surface strain measurement method for the stented artery is presented in this work. ARAMIS stereo optical surface strain measurement system uses two optical high speed cameras to capture the motion of each reference point, and resolve three dimensional strains over the deforming surface8,9. As a mesh stent is deployed into a latex vessel with a random contrasting pattern sprayed or drawn on its outer surface, the surface strain is recorded at every instant of the deformation. The calculated strain distributions can then be used to understand the local lesion response, validate the computational models, and formulate hypotheses for further in vivo study.

Watch this Scientific Journal Video about Monitoring the Wall Mechanics During Stent Deployment in a Vessel at JoVE.com

Monitoring the Wall Mechanics During Stent Deployment in a Vessel

Stent-induced arterial strain distributions are characterized using an optical surface strain measurement system. This visualization technique is used to gain insights into the impact of stent implantation on the host vessel.

Clinical trials have reported different restenosis rates for various stent designs1. It is speculated that stent-induced strain concentrations on the ...

monitoring-the-wall-mechanics-during-stent-deployment-in-a-vessel

Research

JoVE Journal

Bioengineering

9.2K 次观看.  University of Nebraska-Lincoln. 动脉支架诱导应变分布的特点是使用光学表面应变测量系统。这个可视化技术是用于获取到主机上的船只的影响支架植入术的见解。

视频: Monitoring the Wall Mechanics During Stent Deployment in a Vessel

Magnetic Resonance Elastography Methodology for the Evaluation of Tissue Engineered Construct Growth

Traditional mechanical testing often results in the destruction of the sample, and in the case of long term tissue engineered construct studies, the use of destructive assessment is not acceptable. A proposed alternative is the use of an imaging process called magnetic resonance elastography. Elastography is a nondestructive method for determining the engineered outcome by measuring local mechanical property values (i.e., complex shear modulus), which are essential markers for identifying the structure and functionality of a tissue. As a noninvasive means for evaluation, the monitoring of engineered constructs with imaging modalities such as magnetic resonance imaging (MRI) has seen increasing interest in the past decade1. For example, the magnetic resonance (MR) techniques of diffusion and relaxometry have been able to characterize the changes in chemical and physical properties during engineered tissue development2. The method proposed in the following protocol uses microscopic magnetic resonance elastography (&mu;MRE) as a noninvasive MR based technique for measuring the mechanical properties of small soft tissues3. MRE is achieved by coupling a sonic mechanical actuator with the tissue of interest and recording the shear wave propagation with an MR scanner4. Recently, &mu;MRE has been applied in tissue engineering to acquire essential growth information that is traditionally measured using destructive mechanical macroscopic techniques5. In the following procedure, elastography is achieved through the imaging of engineered constructs with a modified Hahn spin-echo sequence coupled with a mechanical actuator. As shown in Figure 1, the modified sequence synchronizes image acquisition with the transmission of external shear waves; subsequently, the motion is sensitized through the use of oscillating bipolar pairs. Following collection of images with positive and negative motion sensitization, complex division of the data produce a shear wave image. Then, the image is assessed using an inversion algorithm to generate a shear stiffness map6. The resulting measurements at each voxel have been shown to strongly correlate (R2&gt;0.9914) with data collected using dynamic mechanical analysis7. In this study, elastography is integrated into the tissue development process for monitoring human mesenchymal stem cell (hMSC) differentiation into adipogenic and osteogenic constructs as shown in Figure 2.

The procedure demonstrates the methodology of magnetic resonance elastography for monitoring the engineered outcome of adipose and osteogenic tissue engineered constructs through noninvasive local assessment of the mechanical properties using microscopic magnetic resonance elastography (&mu;MRE).

Traditional mechanical testing often results in the destruction of the sample, and in the case of long term tissue engineered construct studies, the use ...

Mass Cytometry: Protocol for Daily Tuning and Running Cell Samples on a CyTOF Mass Cytometer

In recent years, the rapid analysis of single cells has commonly been performed using flow cytometry and fluorescently-labeled antibodies. However, the issue of spectral overlap of fluorophore emissions has limited the number of simultaneous probes. In contrast, the new CyTOF mass cytometer by DVS Sciences couples a liquid single-cell introduction system to an ICP-MS.1 Rather than fluorophores, chelating polymers containing highly-enriched metal isotopes are coupled to antibodies or other specific probes.2-5 Because of the metal purity and mass resolution of the mass cytometer, there is no "spectral overlap" from neighboring isotopes, and therefore no need for compensation matrices. Additionally, due to the use of lanthanide metals, there is no biological background and therefore no equivalent of autofluorescence. With a mass window spanning atomic mass 103-203, theoretically up to 100 labels could be distinguished simultaneously. Currently, more than 35 channels are available using the chelating reagents available from DVS Sciences, allowing unprecedented dissection of the immunological profile of samples.6-7
Disadvantages to mass cytometry include the strict requirement for a separate metal isotope per probe (no equivalent of forward or side scatter), and the fact that it is a destructive technique (no possibility of sorting recovery). The current configuration of the mass cytometer also has a cell transmission rate of only ~25%, thus requiring a higher input number of cells.
Optimal daily performance of the mass cytometer requires several steps. The basic goal of the optimization is to maximize the measured signal intensity of the desired metal isotopes (M) while minimizing the formation of oxides (M+16) that will decrease the M signal intensity and interfere with any desired signal at M+16. The first step is to warm up the machine so a hot, stable ICP plasma has been established. Second, the settings for current and make-up gas flow rate must be optimized on a daily basis. During sample collection, the maximum cell event rate is limited by detector efficiency and processing speed to 1000 cells/sec. However, depending on the sample quality, a slower cell event rate (300-500 cells/sec) is usually desirable to allow better resolution between cells events and thus maximize intact singlets over doublets and debris. Finally, adequate cleaning of the machine at the end of the day helps minimize background signal due to free metal.

The steps necessary for daily tuning and optimization of the performance of a CyTOF mass cytometer are described. Comments on optimal sample preparation and flow rate are discussed

In recent years, the rapid analysis of single cells has commonly been performed using flow cytometry and fluorescently-labeled antibodies. However, the ...

A Versatile Automated Platform for Micro-scale Cell Stimulation Experiments

Study of cells in culture (in vitro analysis) has provided important insight into complex biological systems. Conventional methods and equipment for in vitro analysis are well suited to study of large numbers of cells (&ge;105) in milliliter-scale volumes (&ge;0.1 ml). However, there are many instances in which it is necessary or desirable to scale down culture size to reduce consumption of the cells of interest and/or reagents required for their culture, stimulation, or processing. Unfortunately, conventional approaches do not support precise and reproducible manipulation of micro-scale cultures, and the microfluidics-based automated systems currently available are too complex and specialized for routine use by most laboratories. To address this problem, we have developed a simple and versatile technology platform for automated culture, stimulation, and recovery of small populations of cells (100 - 2,000 cells) in micro-scale volumes (1 - 20 &mu;l). The platform consists of a set of fibronectin-coated microcapillaries ("cell perfusion chambers"), within which micro-scale cultures are established, maintained, and stimulated; a digital microfluidics (DMF) device outfitted with "transfer" microcapillaries ("central hub"), which routes cells and reagents to and from the perfusion chambers; a high-precision syringe pump, which powers transport of materials between the perfusion chambers and the central hub; and an electronic interface that provides control over transport of materials, which is coordinated and automated via pre-determined scripts. As an example, we used the platform to facilitate study of transcriptional responses elicited in immune cells upon challenge with bacteria. Use of the platform enabled us to reduce consumption of cells and reagents, minimize experiment-to-experiment variability, and re-direct hands-on labor. Given the advantages that it confers, as well as its accessibility and versatility, our platform should find use in a wide variety of laboratories and applications, and prove especially useful in facilitating analysis of cells and stimuli that are available in only limited quantities.

We have developed an automated cell culture and interrogation platform for micro-scale cell stimulation experiments. The platform offers simple, versatile, and precise control in cultivating and stimulating small populations of cells, and recovering lysates for molecular analyses. The platform is well suited to studies that use precious cells and/or reagents.

Study of cells in culture (in vitro analysis) has provided important insight into complex biological systems. Conventional methods and equipment for in ...

Experimental Investigation of Secondary Flow Structures Downstream of a Model Type IV Stent Failure in a 180&#176; Curved Artery Test Section

The arterial network in the human vasculature comprises of ubiquitously present blood vessels with complex geometries (branches, curvatures and tortuosity). Secondary flow structures are vortical flow patterns that occur in curved arteries due to the combined action of centrifugal forces, adverse pressure gradients and inflow characteristics. Such flow morphologies are greatly affected by pulsatility and multiple harmonics of physiological inflow conditions and vary greatly in size-strength-shape characteristics compared to non-physiological (steady and oscillatory) flows 1 - 7.
Secondary flow structures may ultimately influence the wall shear stress and exposure time of blood-borne particles toward progression of atherosclerosis, restenosis, sensitization of platelets and thrombosis 4 - 6, 8 - 13. Therefore, the ability to detect and characterize these structures under laboratory-controlled conditions is precursor to further clinical investigations.
A common surgical treatment to atherosclerosis is stent implantation, to open up stenosed arteries for unobstructed blood flow. But the concomitant flow perturbations due to stent installations result in multi-scale secondary flow morphologies 4 - 6. Progressively higher order complexities such as asymmetry and loss in coherence can be induced by ensuing stent failures vis-&#224;-vis those under unperturbed flows 5. These stent failures have been classified as &#34;Types I-to-IV&#34; based on failure considerations and clinical severity 14.
This study presents a protocol for the experimental investigation of the complex secondary flow structures due to complete transverse stent fracture and linear displacement of fractured parts (&#34;Type IV&#34;) in a curved artery model. The experimental method involves the implementation of particle image velocimetry (2C-2D PIV) techniques with an archetypal carotid artery inflow waveform, a refractive index matched blood-analog working fluid for phase-averaged measurements 15 - 18. Quantitative identification of secondary flow structures was achieved using concepts of flow physics, critical point theory and a novel wavelet transform algorithm applied to experimental PIV data 5, 6, 19 - 26.

Experimental Investigation of Secondary Flow Structures Downstream of a Model Type IV Stent Failure in a 180&amp;#176; Curved Artery Test Section

Stent implants in stenosed arterial curvatures are prone to "Type IV" failures involving the complete transverse fracture of stents and linear displacement of the fractured parts. We present a protocol for detection of secondary flow (vortical) structures in a curved artery model, downstream of clinically relevant "Type IV" stent failures.

The arterial network in the human vasculature comprises of ubiquitously present blood vessels with complex geometries (branches, curvatures and ...

Adapting the Electrospinning Process to Provide Three Unique Environments for a Tri-layered In Vitro Model of the Airway Wall

Electrospinning is a highly adaptable method producing porous 3D fibrous scaffolds that can be exploited in in vitro cell culture. Alterations to intrinsic parameters within the process allow a high degree of control over scaffold characteristics including fiber diameter, alignment and porosity. By developing scaffolds with similar dimensions and topographies to organ- or tissue-specific extracellular matrices (ECM), micro-environments representative to those that cells are exposed to in situ can be created. 
The airway bronchiole wall, comprised of three main micro-environments, was selected as a model tissue. Using decellularized airway ECM as a guide, we electrospun the non-degradable polymer, polyethylene terephthalate (PET), by three different protocols to produce three individual electrospun scaffolds optimized for epithelial, fibroblast or smooth muscle cell-culture. Using a commercially available bioreactor system, we stably co-cultured the three cell-types to provide an in vitro model of the airway wall over an extended time period.
This model highlights the potential for such methods being employed in in vitro diagnostic studies investigating important inter-cellular cross-talk mechanisms or assessing novel pharmaceutical targets, by providing a relevant platform to allow the culture of fully differentiated adult cells within 3D, tissue-specific environments.

Adapting the Electrospinning Process to Provide Three Unique Environments for a Tri-layered In Vitro Model of the Airway Wall

Advancements in biomaterial technologies enable the development of three-dimensional multi-cell-type constructs. We have developed electrospinning protocols to produce three individual scaffolds to culture the main structural cells of the airway to provide a 3D in vitro model of the airway bronchiole wall.

Electrospinning is a highly adaptable method producing porous 3D fibrous scaffolds that can be exploited in in vitro cell culture. Alterations to ...

Mammalian Cell Encapsulation in Alginate Beads Using a Simple Stirred Vessel

Cell encapsulation in alginate beads has been used for immobilized cell culture in vitro as well as for immunoisolation in vivo. Pancreatic islet encapsulation has been studied extensively as a means to increase islet survival in allogeneic or xenogeneic transplants. Alginate encapsulation is commonly achieved by nozzle extrusion and external gelation. Using this method, cell-containing alginate droplets formed at the tip of nozzles fall into a solution containing divalent cations that cause ionotropic alginate gelation as they diffuse into the droplets. The requirement for droplet formation at the nozzle tip limits the volumetric throughput and alginate concentration that can be achieved. This video describes a scalable emulsification method to encapsulate mammalian cells in 0.5% to 10% alginate with 70% to 90% cell survival. By this alternative method, alginate droplets containing cells and calcium carbonate are emulsified in mineral oil, followed by a decrease in pH leading to internal calcium release and ionotropic alginate gelation. The current method allows the production of alginate beads within 20 min of emulsification. The equipment required for the encapsulation step consists in simple stirred vessels available to most laboratories.

This video and manuscript describe an emulsion-based method to encapsulate mammalian cells in 0.5% to 10% alginate beads which can be produced in large batches using a simple stirred vessel. The encapsulated cells can be cultured in vitro or transplanted for cellular therapy applications.

Cell encapsulation in alginate beads has been used for immobilized cell culture in vitro as well as for immunoisolation in vivo. Pancreatic islet ...

Simulating the Mechanics of Lens Accommodation via a Manual Lens Stretcher

The goal of this protocol is to mimic the biomechanics of physiological accommodation in a cost-efficient, practical manner. Accommodation is achieved through the contraction of the ciliary body and relaxation of zonule fibers, which results in the thickening of the lens necessary for near vision. Here, we present a novel, simple method in which accommodation is replicated by tensing the zonules connected to the lens capsule via a manual lens stretcher (MLS). This method monitors the radial stretching achieved by a lens when subjected to a consistent force and allows for a comparison of accommodating lenses, which can be stretched, to non-accommodating lenses, which cannot be stretched. Importantly, the stretcher couples to the zonules directly, and not to the sclera of the eye, thus only requiring the lens, zonules, and ciliary body rather than the entire globe sample. This difference can significantly decrease the cost of acquiring donor cadaver lenses by about 62% compared to acquiring an entire globe.

We present an efficient method of studying lens accommodation by using a manual lens stretcher. The protocol mimics physiological accommodation by pulling the zonules connected around the lens capsule, thereby, stretching the lens.

The goal of this protocol is to mimic the biomechanics of physiological accommodation in a cost-efficient, practical manner. Accommodation is achieved ...

Nondestructive Monitoring of Degradable Scaffold-Based Tissue-Engineered Blood Vessel Development Using Optical Coherence Tomography

Engineered vascular grafts with structural and mechanical properties similar to natural blood vessels are expected to meet the growing demand for arterial bypass. Characterization of the growth dynamics and remodeling process of degradable polymer scaffold-based tissue-engineered blood vessels (TEBVs) with pulsatile stimulation is crucial for vascular tissue engineering. Optical imaging techniques stand out as powerful tools for monitoring vascularization of engineered tissue enabling high-resolution imaging in real-time culture. This paper demonstrates a nondestructive and fast real-time imaging strategy to monitor the growth and remodeling of TEBVs in long-term culture by using optical coherence tomography (OCT). Geometric morphology is evaluated, including vascular remodeling process, wall thickness, and comparison of TEBV thickness in different culture time points and presence of pulsatile stimulation. Finally, OCT provides practical possibilities for real-time observation of the degradation of polymer in the reconstructing tissues under pulsatile stimulation or not and in each vessel segment, by compared with the assessment of polymer degradation using scanning electron microscopic(SEM) and polarized microscope.

A step by step protocol for nondestructive and long-period monitoring the process of vascular remodeling and scaffold degradation in real-time culture of biodegradable polymeric scaffold-based tissue-engineered blood vessels with pulsatile stimulation using optical coherence tomography is described here.

Engineered vascular grafts with structural and mechanical properties similar to natural blood vessels are expected to meet the growing demand for arterial ...

A Tripeptide-Stabilized Nanoemulsion of Oleic Acid

We describe a method to produce a nanoemulsion composed of an oleic acids-Pt(II) core and a lysine-tyrosine-phenylalanine (KYF) coating (KYF-Pt-NE). The KYF-Pt-NE encapsulates Pt(II) at 10 wt. %, has a diameter of 107 &#177; 27 nm and a negative surface charge. The KYF-Pt-NE is stable in water and in serum, and is biologically active. The conjugation of a fluorophore to KYF allows the synthesis of a fluorescent nanoemulsion that is suitable for biological imaging. The synthesis of the nanoemulsion is performed in an aqueous environment, and the KYF-Pt-NE forms via self-assembly of a short KYF peptide and an oleic acids-platinum(II) conjugate. The self-assembly process depends on the temperature of the solution, the molar ratio of the substrates, and the flow rate of the substrate addition. Crucial steps include maintaining the optimal stirring rate during the synthesis, permitting sufficient time for self-assembly, and pre-concentrating the nanoemulsion gradually in a centrifugal concentrator.

This protocol describes an efficient method to synthesize a nanoemulsion of an oleic acids-platinum(II) conjugate stabilized with a lysine-tyrosine-phenylalanine (KYF) tripeptide. The nanoemulsion forms under mild synthetic conditions via self-assembly of the KYF and the conjugate.

We describe a method to produce a nanoemulsion composed of an oleic acids-Pt(II) core and a lysine-tyrosine-phenylalanine (KYF) coating (KYF-Pt-NE). The ...

Patterning the Geometry of Human Embryonic Stem Cell Colonies on Compliant Substrates to Control Tissue-Level Mechanics

Human embryonic stem cells demonstrate a unique ability to respond to morphogens in vitro by self-organizing patterns of cell fate specification that correspond to primary germ layer formation during embryogenesis. Thus, these cells represent a powerful tool with which to examine the mechanisms that drive early human development. We have developed a method to culture human embryonic stem cells in confined colonies on compliant substrates that provides control over both the geometry of the colonies and their mechanical environment in order to recapitulate the physical parameters that underlie embryogenesis. The key feature of this method is the ability to generate polyacrylamide hydrogels with defined patterns of extracellular matrix ligand at the surface to promote cell attachment. This is achieved by fabricating stencils with the desired geometric patterns, using these stencils to create patterns of extracellular matrix ligand on glass coverslips, and transferring these patterns to polyacrylamide hydrogels during polymerization. This method is also compatible with traction force microscopy, allowing the user to measure and map the distribution of cell-generated forces within the confined colonies. In combination with standard biochemical assays, these measurements can be used to examine the role mechanical cues play in fate specification and morphogenesis during early human development.

Extracellular matrix ligands can be patterned onto polyacrylamide hydrogels to enable the culture of human embryonic stem cells in confined colonies on compliant substrates. This method can be combined with traction force microscopy and biochemical assays to examine the interplay between tissue geometry, cell-generated forces, and fate specification.

Human embryonic stem cells demonstrate a unique ability to respond to morphogens in vitro by self-organizing patterns of cell fate specification that ...