Video: Thyristor Rectifier Circuit with Zero and Non-Zero Firing Angle

Thyristor Rectifier

Genel Bakış

Source: Ali Bazzi, Department of Electrical Engineering, University of Connecticut, Storrs, CT.

Similar to diodes, thyristors, also called silicon controlled rectifiers (SCRs), pass current in one direction from the anode to cathode, and block current flow in the other direction. However, current passage can be controlled through a "gate" terminal, which requires a small current pulse to turn on the thyristor so it can start conducting.

Thyristors are four-layer devices, composed of alternating layers of n-type and p-type material, thereby forming PNPN structures with three junctions. The thyristor has three terminals; with the anode connected to the p-type material of the PNPN structure, the cathode connected to the n-type layer, and the gate connected to the p-type layer nearest the cathode.

The objective of this experiment is to study a controlled thyristor-based half-wave rectifier at different conditions, and understand how different timings of the gate pulse affect the DC output voltage.

Prosedür

ATTENTION: During this experiment, do not touch any part of the circuit while energized. Do NOT ground the VARIAC.

For this experiment, the variable transformer (VARIAC) at a low frequency of 60 Hz and peak of 35 V is used as the main AC source.

1. Setup

Before starting, connect the differential probe to one scope channel.
1. Set the button on the differential probe to 1/20 (or 20X) attenuation.
On the sc

Log in or to access full content. Learn more about your institution’s access to JoVE content here

Sonuçlar

The AC input voltage waveform is chopped until the firing angle. Important relationships of the average output voltage and firing angles for different SCR rectifiers with input V_in= V₀cos(ωt) are:

• Single SCR and R load: <V_out>=V₀[1+cos(α)]/(2π) (2)

Log in or to access full content. Learn more about your institution’s access to JoVE content here

Başvuru ve Özet

SCR's were common in older DC power supplies that required a variable DC output voltage from an AC input. By adjusting the resistor R₂ in the above circuit, it is possible to adjust the average V_out and therefor an adjustable DC power supply results. SCRs are not common any more in DC power supplies as they switch at the input line frequency (typically 50 or 60 Hz), and new power supplies switch at 10 s or 100 s of kHz which makes filtering the output voltage to extract the DC

Log in or to access full content. Learn more about your institution’s access to JoVE content here

Etiketler

Thyristor Silicon Controlled Rectifier SCR Light Dimmers Motor Speed Controllers Voltage Regulators Diode Anode Cathode Gate Current Flow Latching Threshold Rectify AC Power PNPN Structure Circuit Load

ATTENTION: During this experiment, do not touch any part of the circuit while energized. Do NOT ground the VARIAC.

For this experiment, the variable transformer (VARIAC) at a low frequency of 60 Hz and peak of 35 V is used as the main AC source.

1. Setup

Before starting, connect the differential probe to one scope channel.
1. Set the button on the differential probe to 1/20 (or 20X) attenuation.
On the scope channel menu, set the probe to be at 10X unless 20X is available for the differential probe. If 10X is chosen, manually multiply any measurements or results by two to reach the 20X desired.
To setup the VARIAC, make sure the VARIAC output (looks like a regular receptacle) is not connected to any cable.
1. Keep the VARIAC OFF and make sure its knob is set to zero.
2. Slowly adjust the VARIAC knob to around 15% output.
Before connecting the differential probe to the circuit, tie the probe's terminals together and adjust its measured waveform on the screen to show zero offset voltage.
Connect the output cable to the VARIAC, and the differential voltage probe across the VARIAC output banana plugs.
1. Turn the VARIAC ON.
2. Slightly adjust the VARIAC to achieve 35V peak.
Take a copy of V_in to use for reference. Show two to five fundamental cycles.
Turn the VARIAC OFF. Do not adjust its knob setting for the rest of the experiment.

2. Half-Wave Rectifier SCR Circuit with Resistive Load and Zero Firing Angle

The main rectifier component is the SCR (S), which is a TYN058. The load resistor (R) is 51 Ω. The SCR control circuit is enclosed in the dotted box of Fig. 1.
The control circuit uses diodes (1N4004), a 1 kΩ resistor (R₁), a control resistor that is manually changed (R₂), and a ceramic (no polarity) 1 µF capacitor (C).
1. Make sure the SCR and diode polarities are correct. The dash on the diode is at the cathode while the SCR pin assignment is shown in Fig. 2.
On the proto board, build the circuit shown in Fig. 1. Use a short circuit instead of R₂.
Connect the differential voltage probe across the load resistor to observe the output voltage, V_out.
Turn the VARIAC ON.
Adjust the time base on the scope to show V_outfor the same number of fundamental cycles that were captured for V_in. Make a copy of the waveforms.
1. Measure the average or mean V_out.
2. Zoom in between the SCR turn-off point and the next SCR turn-on point. Measure the time difference using the scope cursors. Make a copy of the waveform.
Keep the differential probe connection and other circuit connections the same for the next part.
Turn OFF the VARIAC. Do NOT change the VARIAC voltage setting.

Figure 2: Pin assignment of the SCR.

3. Half-Wave Rectifier SCR Circuit with Resistive Load and Non-Zero Firing Angle

Two different resistors will be used as R₂. The values should be between 100 and 1000 Ω. The resistance can read the resistance color code, or measured with a digital multimeter.

Angle Setting #1 (small R₂)
1. Remove the short circuit, which was previously used instead of R₂.
2. Connect the small resistance value for R₂.
3. Turn the VARIAC ON.
4. Adjust the time base on the scope to show V_out for the same number of fundamental cycles captured for V_in. Make a copy of the waveforms.
5. Measure the average or mean V_out.
6. Zoom in between the SCR turn-off point and the next SCR turn-on point. Measure the time difference using the scope cursors. Make a copy of the waveform.
7. Keep the differential probe connection and other circuit connections the same for the next part.
8. Turn OFF the VARIAC. Do NOT disassemble the circuit or change the VARIAC voltage setting.
Angle Setting #2 (small R₂)
1. Replace R₂ with the larger value resistor.
2. Turn the VARIAC ON.
3. Adjust the time base on the scope to show V_out for the same number of fundamental cycles captured for V_in. Make a copy of the waveforms.
4. Measure the average or mean V_out.
5. Zoom in between the SCR turn-off point and the next SCR turn-on point. Measure the time difference using the scope cursors. Make a copy of the waveform. The mean value should be what is expected from this equation:
  <V_out>=V₀[1+cos(α)]/(2π) (1)
  which is slightly less than half the peak voltage of the input.
6. Turn OFF the VARIAC. Disassemble the circuit and return the VARIAC setting to zero.

Atla...

0:06

Overview

1:19

Principles of the Thyristor Rectifier

3:36

Equipment Setup

5:45

Half-Wave Rectifier Thyristor Circuit with Zero Firing Angle

7:01

Half-Wave Rectifier Thyristor Circuit with Non-zero Firing Angle

8:29

Results

9:06

Applications

10:08

Summary

Bu koleksiyondaki videolar:

article

Now Playing

Thyristor Rectifier

Electrical Engineering

17.4K Görüntüleme Sayısı

article

Electrical Safety Precautions and Basic Equipment

Electrical Engineering

144.5K Görüntüleme Sayısı

article

Characterization of Magnetic Components

Electrical Engineering

15.0K Görüntüleme Sayısı

article

Introduction to the Power Pole Board

Electrical Engineering

12.4K Görüntüleme Sayısı

article

DC/DC Boost Converter

Electrical Engineering

56.7K Görüntüleme Sayısı

article

DC/DC Buck Converter

Electrical Engineering

21.1K Görüntüleme Sayısı

article

Flyback Converter

Electrical Engineering

13.2K Görüntüleme Sayısı

article

Single Phase Transformers

Electrical Engineering

20.1K Görüntüleme Sayısı

article

Single Phase Rectifiers

Electrical Engineering

23.4K Görüntüleme Sayısı

article

Single Phase Inverter

Electrical Engineering

17.9K Görüntüleme Sayısı

article

DC Motors

Electrical Engineering

23.3K Görüntüleme Sayısı

article

AC Induction Motor Characterization

Electrical Engineering

11.6K Görüntüleme Sayısı

article

VFD-fed AC Induction Machine

Electrical Engineering

6.9K Görüntüleme Sayısı

article

AC Synchronous Machine Synchronization

Electrical Engineering

21.5K Görüntüleme Sayısı

article

AC Synchronous Machine Characterization

Electrical Engineering

14.2K Görüntüleme Sayısı

Telif Hakkı © 2020 MyJove Corporation. Tüm hakları saklıdır