This work was supported by AAUW international fellowship to Adeola Adewola, NIH/NCRR (U42RR023245) to Jose Oberholzer, and The Chicago Diabetes Project.

A. Microfabrication of 3-layer microfluidic perifusion device
Bottom Well Master Protocol (150 &mu;m deep wells)
<ol>
 <li>Clean the wafer using a razor blade if needed. Clean with Acetone, Methanol, and IPA. Perform plasma treatment at 50 Watts for 30 s.</li>
 <li>Spin SU8-100 @ 2000 rpm. [Step 1: 500 rpm, 10 s, 100 rpm/s, Step 2: 2000 rpm, 30 s, 300 rpm/s]. [NOTE: do not hold the wafer with tweezers after spinning SU8]</li>
 <li>Soft bake the wafer at 65 &deg;C for 20 min and at 95 &deg;C for 50 min. </li>
 <li>The wafer is exposed to UV light through a desired mask. Dose for 150 &mu;m height is 650 mJ/cm2.</li>
 <li>Post exposure bake the wafer at 65 &deg;C for 1 min and at 95 &deg;C for 12 min. </li>
 <li>Develop the wafer in SU8 developer for 15 min.</li>
</ol>
Microchannel Master Protocol (500 &mu;m deep wells)
<ol>
 <li>Clean the wafer using a razor blade if needed. Clean with Acetone, Methanol, and IPA. Perform plasma treatment at 50 Watts for 30 s.</li>
 <li>Spin SU8-2150 @ 1000 rpm. [Step 1: 500 rpm, 10 s, 100 rpm/s, Step 2: 1000 rpm, 30 s, 300 rpm/s].</li>
 <li>Soft bake the wafer at 65 &deg;C for 15 min and at 95 &deg;C for 2 hrs and 30 min. </li>
 <li>The wafer is exposed to UV light through a desired mask. Exposure dose for 650 &mu;m height is 685 mJ/cm2.</li>
 <li>Post exposure bake the wafer at 65 &deg;C for 5 min and at 95 &deg;C for 35 min. </li>
 <li>Develop the wafer in SU8 developer for 20-30 min.</li>
</ol>
PDMS solution preparation
<ol>
 <li>Polydimethylsiloxane (PDMS) solution is prepared by thoroughly mixing 10 parts of silicone elastomer with 1 part of curing agent of a standard Sylgard 184 kit.</li>
 <li>The bubbles generated in the PDMS solution during the mixing process are removed using a vacuum desiccator.</li>
 <li>The bubble-free PDMS solution is slowly dispensed onto the SU8 masters and an empty Petri dish for the third layer. </li>
 <li>The temperature of the hot plate is set to 75 &deg;C and the PDMS is cured at this temperature for 2 hrs</li>
 <li>Inlets, outlets and exchange wells are punched out using the appropriate size hole puncher.</li>
 <li>The layers are bonded together on a glass slide (size 0.1 mm) using a handheld plasma device.</li>
</ol>
B. Experimental setup
<ol>
 <li>Flow 70 % ethanol through the micro-device to sterilize. Flow DI water to wash out the ethanol. Perfuse 50 ml of 0.5 %BSA through the device to prevent non specific adsorption of insulin to the microchannel walls.</li>
 <li>The glucose ramp gradient and other related gradients generated by LabView software that communicates with the syringe pumps are tested to make sure the gradients are stable.</li>
 <li>25-30 mice islets were incubated with 5 &mu;M Fura-2/AM (a calcium indicator, Molecular probes, CA) and 2.5 &mu;M Rhodamine 123 (Rh123, a mitochondrial potentials indicator, Sigma, MO) for 30 min at 37 &deg;C in Krebs-Ringer buffer (KRB) containing 2 mM glucose </li>
 <li>The mice islets are carefully pipetted into microfluidic perifusion device through the inlet port. </li>
 <li>The microfluidic network is then setup by connecting the inlet to the syringe pumps using Tygon tubing and a Y-connector and the outlet to fraction collector. The device sits on a heating stage (37 &deg;C) on the microscope and the inlet tubing is heated on a hotplate to keep the temperature of the chamber and solution at 37 &deg;C. </li>
 <li>Immediately after setup, the mice islets are perifused with KRB containing 2 mM glucose for 10 min and then a glucose ramp (2mM 25mM) for 25 min. </li>
 <li>Time-lapse images are collected and analyzed every 15 s by SimplePCI software. The perifusate is also collected every minute using a fraction collector to analyze the insulin secretion using ELISA kit.</li>
 </ol>
Representative Results
Mouse islets were perifused with a linear gradient of 2-25 mM glucose. As shown in Figure 1, calcium influx and insulin secretion are triggered after about 13 minutes of perifusion, corresponding to 6 mM glucose. Changes in Mitochondrial potentials are seen earlier as expected, at about 11 minutes. This data demonstrates the advantage of using this microfluidic network to characterize islet physiology.
<img src="/files/ftp_upload/1649/1649fig1.jpg" alt="Figure 1" /> Figure 1. Physiological responses to islet cell stimulation.

<ol>
	<li>Mohammed, J. S., Wang, Y., Harvat, T. A., Oberholzer, J., Eddington, D. T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Microfluidic+device+for+multimodal+characterization+of+pancreatic+islets.">Microfluidic device for multimodal characterization of pancreatic islets.</a> Lab Chip. 9, 97-106 (2009).</li></ol>

Traditional islet perifusion systems (macroscale and microscale) have some limitations including complex of setup and design, high technical requirements, and difficulty to create user-prescribed chemical gradients in the system. The microfluidic perifusion system described here overcomes these limitations with simple geometry of design and fabrication. More important, this system can be integrated with fluorescence imaging approach that provide as a unique tool to study islet physiology. The system demonstrated with hig...

<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="http://www.w3.org/1999/xhtml" xml:lang="en" lang="en">	
		
		<div>
		<table border="1">
		<thead>
		<tr>
		<th>Material Name</th>
		<th>Type</th>
		<th>Company</th>
		<th>Catalogue Number</th>
		<th>Comment</th>
		</tr>
		</thead>
		<tbody>
		
<tr>
<td>60ml Syringes</td>
<td>&nbsp;</td>
<td>BD</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<tr>
<td>Fura-2 fluorescence dye</td>
<td>&nbsp;</td>
<td>Molecular Probes Inc.</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<tr>
<td>Rhodamine123 Fluorescence dye</td>
<td>&nbsp;</td>
<td>Molecular Probes Inc.</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<tr>
<td>Glucose</td>
<td>&nbsp;</td>
<td>Sigma</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<tr>
<td>Bovine Serum Albumin</td>
<td>&nbsp;</td>
<td>Sigma</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<tr>
<td>30" Silicone tubings</td>
<td>&nbsp;</td>
<td>Cole Palmer</td>
<td>&nbsp;</td>
<td>1/16 x 1/8in</td>
</tr>
<tr>
<td>1.5ml Eppendorf tubes</td>
<td>&nbsp;</td>
<td>Fisher</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<tr>
<td>Y-connectors</td>
<td>&nbsp;</td>
<td>Cole Palmer</td>
<td>&nbsp;</td>
<td>1/16&#x201D; &amp; 4mm</td>
</tr>
<tr>
<td>Syringe connectors</td>
<td>&nbsp;</td>
<td>Cole Palmer</td>
<td>&nbsp;</td>
<td>female luer plug 1/16&#x201D;</td>
</tr>
<tr>
<td>Straight connectors</td>
<td>&nbsp;</td>
<td>Cole Palmer</td>
<td>&nbsp;</td>
<td>1/16&#x201D;</td>
</tr>
<tr>
<td>Elbow connector</td>
<td>&nbsp;</td>
<td>Cole Palmer</td>
<td>&nbsp;</td>
<td>1/16&#x201D;</td>
</tr>
<tr>
<td>Havard syringe pump</td>
<td>&nbsp;</td>
<td>Harvard Apparatus</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<tr>
<td>Perifusion device</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<tr>
<td>Hot plate</td>
<td>&nbsp;</td>
<td>PMC</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<tr>
<td>Thermometer</td>
<td>&nbsp;</td>
<td>Omega Engineering Inc.</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<tr>
<td>Fraction collector</td>
<td>&nbsp;</td>
<td>Gibson</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<tr>
<td>Pippettor</td>
<td>&nbsp;</td>
<td>Fisher</td>
<td>&nbsp;</td>
<td>&nbsp;</td>
<tr>
<td>Inverted epiflorescence microscope</td>
<td>&nbsp;</td>
<td>Olympus</td>
<td>IX71</td>
<td>&nbsp;</td>
<tr>
<td>Charge-coupled device</td>
<td>&nbsp;</td>
<td>QImaging</td>
<td>&nbsp;</td>
<td>Retiga-SRV, Fast 1394</td>
</tr>		</tbody>
		</table>
		</div>

a multi-parametric islet perifusion system within a microfluidic perifusion device

A microfluidic islet perifusion device was developed for the assessment of dynamic insulin secretion of multiple islets and simultaneous fluorescence imaging of calcium influx and mitochondrial potential changes. The device consists of three layers: first layer contains an array of microscale wells (500 &mu;m diameter and 150 &mu;m depth) that help to immobilize the islets while exposed to flow and maximize the exposed surface area of the islets; the second layer contains a circular perifusion chamber (3 mm deep, 7 mm diameter); and the third layer contains an inlet-mixing channel that fans out before injection into the perifusion chamber (2 mm in width, 19 mm in length, and 500 &mu;m in height) for optimizing the mixing efficiency prior to entering the perifusion chamber. The creation of various glucose gradients including a linear, bell shape, and square shapes also can be created in the microfluidic perifusion network and is demonstrated.

Watch this Scientific Journal Video about A Multi-Parametric Islet Perifusion System within a Microfluidic Perifusion Device at JoVE.com

A Multi-Parametric Islet Perifusion System within a Microfluidic Perifusion Device

A microfluidic islet perifusion device was developed for the assessment of dynamic insulin secretion of multiple islets and simultaneous fluorescence imaging of calcium influx and mitochondrial potential changes.

A microfluidic islet perifusion device was developed for the assessment of dynamic insulin secretion of multiple islets and simultaneous fluorescence ...

a-multi-parametric-islet-perifusion-system-within-microfluidic

Research

JoVE Journal

Biology

11.8K Views.  University of Illinois, Chicago. A microfluidic islet perifusion device was developed for the assessment of dynamic insulin secretion of multiple islets and simultaneous fluorescence imaging of calcium influx and mitochondrial potential changes. 

Video: A Multi-Parametric Islet Perifusion System within a Microfluidic Perifusion Device

Murine Pancreatic Islet Isolation

Fabrication of a Microfluidic Device for the Compartmentalization of Neuron Soma and Axons

In this video, we demonstrate the technique of soft lithography with polydimethyl siloxane (PDMS) which we use to fabricate a microfluidic device for culturing neurons. Previously, a silicon wafer was patterned with the design for the neuron microfluidic device using SU-8 and photolithography to create a master mold, or what we simply refer to as a "master". Next, we pour the silicon polymer PDMS on top of the master which is then cured by heating the PDMS to 80&deg;C for 1 hour. The PDMS forms a negative mold of the device. The PDMS is then carefully cut and lifted away from the master. Holes are punched where the reservoirs will be and the excess PDMS trimmed away from the device. Nitrogen is used to blow away any excess debris from the device. At this point the devices are now ready for use and can either bonded to corning No. 1 cover glass with a plasma sterilizer/cleaner or can be reversibly bound to the cover glass by simply placing the device on top of the cover glass. The reversible bonding of the device to glass is covered in a separate video and requires first that the device be sterilized either with 70% ethanol or by autoclaving. Plasma treating sterilizes the devices so no further treatment is necessary. It is, however, important, when plasma-treating the devices, to add liquid to the devices within 10 minutes of the plasma treatment while the surfaces are still hydrophilic. Waiting longer than 10 minutes to add liquid to the device makes it difficult for the liquid to enter the device. The neuron devices are typically plasma-bound to cover glass and 0.5 mg/ml poly-L-lysine (PLL) in pH 8.5 borate buffer is immediately added to the device. After a minimum of 3 hours incubating with PLL, the devices are washed with dH2O water a minimum of 3 times with at least 15 minutes between each wash. Next, the water is removed and fresh media is added to the device. At this point the device is ready for use. It is important to remember at this point to never remove all the media from the device. Always leave media in the main channel.

In this video we demonstrate the technique of soft lithography with polydimethyl siloxane (PDMS) which we use to farbricate a microfluidic device for culturing neurons.

In this video, we demonstrate the technique of soft lithography with polydimethyl siloxane (PDMS) which we use to fabricate a microfluidic device for ...

A Microfluidic Device with Groove Patterns for Studying Cellular Behavior

We describe a microfluidic device with microgrooved patterns for studying cellular behavior. This microfluidic platform consists of a top fluidic channel and a bottom microgrooved substrate. To fabricate the microgrooved channels, a top poly(dimethylsiloxane) (PDMS) mold containing the impression of the microfluidic channels was aligned and bonded to a microgrooved substrate. Using this device, mouse fibroblast cells were immobilized and patterned within microgrooved substrates (25, 50, 75, and 100 &mu;m wide). To study apoptosis in a microfluidic device, media containing hydrogen peroxide, Annexin V, and propidium iodide was perfused into the fluidic channel for 2 hours. We found that cells exposed to the oxidative stress became apoptotic. These apoptotic cells were confirmed by Annexin V that bound to phosphatidylserine at the outer leaflet of the plasma membrane during the apoptosis process. Using this microfluidic device with microgrooved patterns, the apoptosis process was observed in real-time and analyzed by using an inverted microscope containing an incubation chamber (37&deg;C, 5% CO2). Therefore, this microfluidic device incorporated with microgrooved substrates could be useful for studying the cellular behavior and performing high-throughput drug screening.

We describe a protocol for the fabrication of microfluidic devices that can enable cell capture and culture. In this approach patterned microstructures such as grooves within microfluidic channels are used to create low shear stress regions within which cell can dock.

We describe a microfluidic device with microgrooved patterns for studying cellular behavior.  This microfluidic platform consists of a top fluidic channel ...

A Gradient-generating Microfluidic Device for Cell Biology

 The fabrication and operation of a gradient-generating microfluidic device for studying cellular behavior is described.  A microfluidic platform is an enabling experimental tool, because it can precisely manipulate fluid flows, enable high-throughput experiments, and generate stable soluble concentration gradients.  Compared to conventional gradient generators, poly(dimethylsiloxane) (PDMS)-based  microfluidic devices can generate stable concentration gradients of growth factors with well-defined profiles.  Here, we developed simple gradient-generating microfluidic devices with three separate inlets.  Three microchannels combined into one microchannel to generate concentration gradients.  The stability and shape of growth factor gradients were confirmed by fluorescein isothyiocyanate (FITC)-dextran with a molecular weight similar to epidermal growth factor (EGF).  Using this microfluidic device, we demonstrated that fibroblasts exposed to concentration gradients of EGF migrated toward higher concentrations.  The directional orientation of cell migration and motility of migrating cells were quantitatively assessed by cell tracking analysis.  Thus, this gradient-generating microfluidic device might be useful for studying and analyzing the behavior of migrating cells.

We describe a protocol for the microfabrication of the gradient-generating microfluidic device that can generate spatial and temporal gradients in well-defined microenvironment. In this approach, the gradient-generating microfluidic device can be used to study directed cell migration, embryogenesis, wound healing, and cancer metastasis.

 The fabrication and operation of a gradient-generating microfluidic device for studying cellular behavior is described.  A microfluidic platform is an ...

Preparing E18 Cortical Rat Neurons for Compartmentalization in a Microfluidic Device

In this video, we demonstrate the preparation of E18 cortical rat neurons. E18 cortical rat neurons are obtained from E18 fetal rat cortex previously dissected and prepared. The E18 cortex is, upon dissection, immediately dissociated into individual neurons. It is possible to store E18 cortex in Hibernate E buffer containing B27 at 4&deg;C for up to a week before the dissociation is performed. However, there will be a drop in cell viability. Typically we obtain our E18 Cortex fresh. It is transported to the lab in ice cold Calcium free Magnesium free dissection buffer (CMFM). Upon arrival, trypsin is added to the cortex to a final concentration of 0.125%. The cortex is then incubated at 37&deg;C for 8 minutes. DMEM containing 10% FBS is added to the cortex to stop the reaction. The cortex is then centrifuged at 2500 rpm for 2 minutes. The supernatant is removed and 2 ml of Neural Basal Media (NBM) containing 2% B27 (vol/vol) and 0.25% Glutamax (vol/vol) is added to the cortex which is then re-suspended by pipetting up and down. Next, the cortex is triturated with previously fire polished glass pipettes, each with a successive smaller opening. After triturating, the cortex is once again centrifuged at 2500 rpm for 2 minutes. The supernatant is then removed and the cortex pellet re-suspended with 2 ml of NBM containing B27 and Glutamax. The cell suspension is then passed through a 40 um nylon cell strainer. Next the cells are counted. The neurons are now ready for loading into the neuron microfluidic device.

In this video we demonstrate the preparation of E18 Cortical Rat Neurons.

In this video, we demonstrate the preparation of E18 cortical rat neurons. E18 cortical rat neurons are obtained from E18 fetal rat cortex previously ...

Cell Capture Using a Microfluidic Device

Assessing Neural Stem Cell Motility Using an Agarose Gel-based Microfluidic Device

While microfluidic technology is reaching a new level of maturity for macromolecular assays, cell-based assays are still at an infant stage1. This is largely due to the difficulty with which one can create a cell-compatible and steady microenvironment using conventional microfabrication techniques and materials. We address this problem via the introduction of a novel microfabrication material, agarose gel, as the base material for the microfluidic device. Agarose gel is highly malleable, and permeable to gas and nutrients necessary for cell survival, and thus an ideal material for cell-based assays. We have shown previously that agarose gel based devices have been successful in studying bacterial and neutrophil cell migration2. In this report, three parallel microfluidic channels are patterned in an agarose gel membrane of about 1mm thickness. Constant flows with media/buffer are maintained in the two side channels using a peristaltic pump. Cells are maintained in the center channel for observation. Since the nutrients and chemicals in the side channels are constantly diffusing from the side to center channel, the chemical environment of the center channel is easily controlled via the flow along the side channels. Using this device, we demonstrate that the movement of neural stem cells can be monitored optically with ease under various chemical conditions, and the experimental results show that the over expression of epidermal growth factor receptors (EGFR) enhances the motility of neural stem cells. Motility of neural stem cells is an important biomarker for assessing cells aggressiveness, thus tumorigenic factor3. Deciphering the mechanism underlying NSC motility will yield insight into both disorders of neural development and into brain cancer stem cell invasion.

We demonstrate that the over expression of epidermal growth factor receptors (EGFR) enhances the motility of neural stem cells(NSCs) using a novel agarose gel based microfluidic device. This technology can be readily adaptable to other mammalian cell systems where cell sources are scarce, such as human neural stem cells, and the turn around time is critical.

While microfluidic technology is reaching a new level of maturity for macromolecular assays, cell-based assays are still at an infant stage1. This is ...

A Multi-compartment CNS Neuron-glia Co-culture Microfluidic Platform

We present a novel multi-compartment neuron co-culture microsystem platform for in vitro CNS axon-glia interaction research, capable of conducting up to six independent experiments in parallel for higher-throughput. We developed a new fabrication method to create microfluidic devices having both micro and macro scale structures within the same device through a single soft-lithography process, enabling mass fabrication with good repeatability.
The multi-compartment microfluidic co-culture platform is composed of one soma compartment for neurons and six axon/glia compartments for oligodendrocytes (OLs). The soma compartment and axon/glia compartments are connected by arrays of axon-guiding microchannels that function as physical barriers to confine neuronal soma in the soma compartment, while allowing axons to grow into axon/glia compartments. OLs loaded into axon/glia compartments can interact only with axons but not with neuronal soma or dendrites, enabling localized axon-glia interaction studies. The microchannels also enabled fluidic isolation between compartments, allowing six independent experiments to be conducted on a single device for higher throughput.
Soft-lithography using poly(dimethylsiloxane) (PDMS) is a commonly used technique in biomedical microdevices. Reservoirs on these devices are commonly defined by manual punching. Although simple, poor alignment and time consuming nature of the process makes this process not suitable when large numbers of reservoirs have to be repeatedly created. The newly developed method did not require manual punching of reservoirs, overcoming such limitations. First, seven reservoirs (depth: 3.5 mm) were made on a poly(methyl methacrylate) (PMMA) block using a micro-milling machine. Then, arrays of ridge microstructures, fabricated on a glass substrate, were hot-embossed against the PMMA block to define microchannels that connect the soma and axon/glia compartments. This process resulted in macro-scale reservoirs (3.5 mm) and micro-scale channels (2.5 &mu;m) to coincide within a single PMMA master. A PDMS replica that served as a mold master was obtained using soft-lithography and the final PDMS device was replicated from this master.
Primary neurons from E16-18 rats were loaded to the soma compartment and cultured for two weeks. After one week of cell culture, axons crossed microchannels and formed axonal only network layer inside axon/glia compartments. Axons grew uniformly throughout six axon/glia compartments and OLs from P1-2 rats were added to axon/glia compartments at 14 days in vitro for co-culture.

We developed a novel multi-compartment neuron co-culture microsystem platform for in vitro CNS axon-glia interaction research. The platform is capable of conducting up to six independent experiments in parallel and was fabricated using a newly developed macro/micro hybrid fabrication method.

We present a novel multi-compartment neuron co-culture microsystem platform for in vitro CNS axon-glia interaction research, capable of conducting up to ...

A Microfluidic Device for Quantifying Bacterial Chemotaxis in Stable Concentration Gradients

Chemotaxis allows bacteria to approach sources of attractant chemicals or to avoid sources of repellent chemicals. Bacteria constantly monitor the concentration of specific chemoeffectors by comparing the current concentration to the concentration detected a few seconds earlier. This comparison determines the net direction of movement. Although multiple, competing gradients often coexist in nature, conventional approaches for investigating bacterial chemotaxis are suboptimal for quantifying migration in response to concentration gradients of attractants and repellents. Here, we describe the development of a microfluidic chemotaxis model for presenting precise and stable concentration gradients of chemoeffectors to bacteria and quantitatively investigating their response to the applied gradient. The device is versatile in that concentration gradients of any desired absolute concentration and gradient strength can be easily generated by diffusive mixing. The device is demonstrated using the response of Escherichia coli RP437 to gradients of amino acids and nickel ions.

This protocol describes the development of a microfluidic device for investigating bacterial chemotaxis in stable concentration gradients of chemoeffectors.

Chemotaxis allows bacteria to approach sources of attractant chemicals or to avoid sources of repellent chemicals. Bacteria constantly monitor the ...

A Method for Mouse Pancreatic Islet Isolation and Intracellular cAMP Determination

Uncontrolled glycemia is a hallmark of diabetes mellitus and promotes morbidities like neuropathy, nephropathy, and retinopathy. With the increasing prevalence of diabetes, both immune-mediated type 1 and obesity-linked type 2, studies aimed at delineating diabetes pathophysiology and therapeutic mechanisms are of critical importance. The &#946;-cells of the pancreatic islets of Langerhans are responsible for appropriately secreting insulin in response to elevated blood glucose concentrations. In addition to glucose and other nutrients, the &#946;-cells are also stimulated by specific hormones, termed incretins, which are secreted from the gut in response to a meal and act on &#946;-cell receptors that increase the production of intracellular cyclic adenosine monophosphate (cAMP). Decreased &#946;-cell function, mass, and incretin responsiveness are well-understood to contribute to the pathophysiology of type 2 diabetes, and are also being increasingly linked with type 1 diabetes. The present mouse islet isolation and cAMP determination protocol can be a tool to help delineate mechanisms promoting disease progression and therapeutic interventions, particularly those that are mediated by the incretin receptors or related receptors that act through modulation of intracellular cAMP production. While only cAMP measurements will be described, the described islet isolation protocol creates a clean preparation that also allows for many other downstream applications, including glucose stimulated insulin secretion, [3H]-thymidine incorporation, protein abundance, and mRNA expression.

Assaying in vitro &#946;-cell function using isolated mouse islets of Langerhans is an important component in the study of diabetes pathophysiology and therapeutics. While many&#160;downstream applications are available, this protocol specifically describes the measurement of intracellular cyclic adenosine monophosphate (cAMP) as an essential parameter determining &#946;-cell function.

Uncontrolled glycemia is a hallmark of diabetes mellitus and promotes morbidities like neuropathy, nephropathy, and retinopathy. With the increasing ...

Methods Article

A Multi-Parametric Islet Perifusion System within a Microfluidic Perifusion Device